Model #713 US patent #’s 9,422,132 & 10,150,645 ™ Revolution Owner’s Manual VISIT OUR WEBSITE: WWW.LIBERTYGARDENPRODUCTS.COM OR CALL US TOLL FREE AT 1-866-820-5805 LIBERTY GARDEN PRODUCTS, INC.
PRE-ASSEMBLY Estimated Assembly Time : 10 minutes (not including mounting the hose reel) TOOLS REQUIRED: AA AA. Allen wrench (Supplied) Pliers Adjustable wrench Drill HARDWARE INCLUDED CC BB BB. Allen bolts (2) DD CC. Lock nuts (2) DD. Allen screw (1) Note: Hardware not shown to actual size. The wall mounting hardware is NOT included with this unit. Check with the retailer or visit a hardware store to purchase. PARTS LIST A. Crank handle (1) B. Leader hose (1) C. Base shelf (1) D.
This hose reel must be mounted to a solid masonry wall or to wall studs TI P : Remember to use the correct size and quantity of hardware to properly support the total weight of the unit. A standard 100' length of garden hose weighs approximately 15 lbs. F illed with water the additional weight can exceed 20 lbs. The mounting hardware must be able to support the combined weight of the unit, garden hose, plus water. INSTALLATION 1 . B R IC K OR M A S ONR Y A NC H OR S L E E V E S : 2 .
ASSEMBLY 1 2 Attach the hose reel (D) to the base shelf (C) by hanging the reel on the small slot located at the front of the base. Line up the holes in the hose reel (D) with the base shelf (C) and insert long Allen bolts (BB). C C FIGURE 1 FIGURE 2 BB D D FIGURE 3 3 C Tighten Allen bolts (BB) with the supplied Allen wrench (AA). At the same time using fingers, screw on lock nuts (CC) to secure base shelf (C) to hose reel (D).
ASSEMBLY 4 FIGURE 4 A Align the holes in the crank handle (A) with the crank handle shaft on the hose reel (D). Insert the short Allen screw (DD) into the crank handle and tighten with supplied Allen wrench (AA). AA A 5 6 DD Attach leader hose (B) to swivel connector on the hose reel (D). Attach end of leader hose to water source. Attach your garden hose to the hose connector on the hose reel (D). The hose is now ready to wind around the spool. The Revolution holds up to 150 ft.
OPERATING INSTRUCTIONS 1 2 Pull up on handle knob located on the base shelf (C) then rotate hose reel (D) to one of the twenty-four locking positions. C FIGURE 1 Pull up on the handle knob located on the base shelf (C) and turn the locking pin to the up position. The Revolution rotating hose reel will now turn a full 360 degrees. D FIGURE 2 FIGURE 3 C 3 4 C Release the handle on the base shelf (C) and lock unit into one of the desired positions.
CARE INSTRUCTIONS Leaks Your hose reel is manufactured with the finest quality components available. All components are manufactured to rigorous quality standards not common in other consumer grade hose reels available today. When you install your hose reel, be sure the hose washers are in place and all fittings are secure. DO NOT OVER TIGHTEN as you might damage the components. If you live in more temperate climates, be sure to drain the unit of any residual water before storing.
CURING A LEAKING SWIVEL Problem: Your new Revolution rotating hose reel is leaking at the swivel. Solution: It is normal for the swivel to leak slightly until the O-rings are wet and have seated. If the leaking continues, you don’t need to take the reel back to the store. This is a simple problem and is easily fixed by a few simple procedures. 1. If the leader hose is attached to the swivel, unscrew the hose and look inside the swivel. 2.
WARRANTY Our guarantee is as functional and straight-forward as our products. Since we design and build our products to provide you with many years of satisfaction, all Liberty™ products are guaranteed against defects in materials and workmanship. In the unlikely event that a problem arises as a result of a defect in our materials or workship, we will promptly repair or replace the item at our expense. All we require is that you contact us first and we'll take it from there.