User Manual

ManualsBrandsLiberty Pumps ManualsPumpsD3696-Series

IMPORTANT:

Prior to installation, record Model, Serial Number, and

Code Number from pump nameplate for future reference.

MODEL ________________________

SERIAL ______________________

CODE ______________________

INSTALLATION

DATE _______________________

Installation Manual

7353000E

Features:

 36” Diameter Fiberglass Tank

 Available in 48”, 60”, 72”, 84”, and 96” heights

 LSG Single or LSGX 2 Stage 2HP Grinder Pumps

 Factory Installed Guide Rail System

 Quick Tree™ pre-mounted float system

 NEMA 4X Junction Box

 NEMA 4X Duplex Alternating Control Panel

Contents

1. General Information

2. Precautions / Pre-Installation

3. Installation Instructions

4. Maintenance & Troubleshooting

5. GR20 Assembly

D3600- Series Duplex Grinder Systems

7000 Apple Tree Avenue

Bergen, NY 14416

Phone: (800) 543-2550

Fax: (585) 494-1839

www.libertypumps.com

Summary of content (6 pages)

PAGE 1
Installation Manual 7353000E D3600- Series Duplex Grinder Systems Features:  36” Diameter Fiberglass Tank  Available in 48”, 60”, 72”, 84”, and 96” heights  LSG Single or LSGX 2 Stage 2HP Grinder Pumps  Factory Installed Guide Rail System  Quick Tree™ pre-mounted float system  NEMA 4X Junction Box  NEMA 4X Duplex Alternating Control Panel Contents 1. General Information 2. Precautions / Pre-Installation 3. Installation Instructions 4. Maintenance & Troubleshooting 5.
PAGE 2
1 General Information GRINDER PUMP SPECIFICATIONS MODEL H P VOLTAGE PHASE FULL LOAD AMPS LOCKED ROTOR AMPS THERMAL OVERLOAD TEMP STATOR WINDING CLASS SHUT-OFF HEAD CORD LENGTH FT DISCHARGE LSG202A 2 208/230 1 15 53 135˚C 275°F B 108’ 25 1-1/4” LSG202M 2 208/230 1 15 53 135˚C 275°F B 108’ 25 1-1/4” LSG202M-C* 2 208/230 1 15 53 135˚C 275°F B 108’ 35 1-1/4” LSG203M 2 208/230 3 10.6 61 N/A B 108’ 25 1-1/4” LSG204M 2 440/460 3 5.
PAGE 3
Pre-installation checklist: 1. Inspect the unit upon arrival to ensure that there is no shipping damage. Pay careful attention to the condition of the fiberglass basin, control floats, pump guide rail brackets, and control panel. Notify the carrier immediately if there is any damage. 4. Check to ensure that your power source is adequate to handle the pump amperage as noted above and on the pump nameplate. Ensure that the electrical supply circuit is equipped with fuses or breakers of the proper capacity.
PAGE 4
Control Panel: 4. Risk of Electric shock: This pump is supplied with a grounding conductor. To reduce the risk of electric shock, be certain that it is connected only to a properly grounded earth wire. All electrical circuitry should be installed in accordance with the National Electric Code (NEC) and all applicable local codes or ordinances. The control panel that is an integral part of this complete unit is supplied with its own separate Installation/Operation/Maintenance manual.
PAGE 5
GR20 Quick Disconnect Assembly GR20 Assembly The GR20 quick disconnect assembly provided with your grinder package system is designed to allow easy installation and removal of the pump. When installed correctly it will seal and provide a means to lift the pump without disconnecting any of the discharge piping. Please ensure that installation is done as per the diagrams below. ENSURE THAT GROMMET IS PROPERLY INSTALLED INSTALL 3/8X16 HEX BOLTS HERE.
PAGE 6
3 Year Limited Warranty Liberty Pumps, Inc. warrants that pumps of its manufacture are free from all factory defects in material and workmanship for a period of 3 years from the date of purchase. The date of purchase shall be determined by a dated sales receipt noting the model and serial number of the pump. The dated sales receipt must accompany the returned pump if the date of return is more than 3 years from the "CODE" (date of manufacture) number noted on the pump nameplate.