Power Strips Quick-Start Guide

ManualsBrandsLiebert ManualsSurge ProtectorPower Strips

LIEBERT MP™ ADVANCED POWER STRIPS

QUICK-START GUIDE: OPENCOMMS EM OR MP ADVANCED ACCESS SERVER

SAVE THESE IMPORTANT SAFETY INSTRUCTIONS

This manual contains important safety instructions. Read all safety, installation and operating

instructions before installing the Liebert MP Advanced Power Strip or Access Server. Adhere to all

warnings on the unit and in this manual. Follow all operating and user instructions. Individuals

without previous training can install and operate this equipment.

The Liebert MP Advanced Power Strip and Access Server are not intended for use with life support or

other designated critical devices. Maximum load must not exceed that shown on the Liebert MP

Advanced Power Strip or Access Server rating label. The Liebert MP Advanced Power Strip and

Access Server are designed for data processing equipment. If uncertain, consult your local dealer or

Liebert representative.

Operate the Liebert MP Advanced Power Strip and Access Server in an indoor environment only in an

ambient temperature range of 32°F to +104°F (0°C to +40°C). Install it in a clean environment, free

from conductive contaminants, moisture, flammable liquids, gases and corrosive substances.

Never block or insert any object into the Liebert MP Advanced Power Strip or Access Server.

DO NOT CONNECT equipment that could overload the Liebert MP Advanced Power Strip or Access

Server.

Refer to the Liebert MP Advanced Power Strip and Access Server user manual, SL-20815, to deter-

mine the electrical ratings and specifications of your Liebert MP Advanced Power Strip or Access

Server. It is imperative that the power supply and connections match the specifications of the power

strip or access server being installed.

WARNING

Opening or removing the cover of MP Advanced Power Strips or Access Servers may expose

you to lethal voltages within the unit.

Observe all cautions and warnings in this manual. Failure to do so may result in serious

injury or death. Do not attempt to service this product yourself. Refer all service to qualified

service personnel. Never work alone.

WARNING

The Liebert MP Advanced Power Strip and Access Server contain no user serviceable parts.

Under no circumstances attempt to gain internal access due to risk of electric shock or burn.

Do not continue to use the Liebert MP Advanced Power Strip or Access Server if the LED

panel or monitoring interface indicators are not in accordance with these operating

instructions. Refer all faults to your local dealer or Liebert representative.

CAUTION

Connecting your Liebert MP Advanced Power Strip, Access Server or rack equipment to a

power supply with an incorrect rating in either voltage, amperes or phase may damage the

connected equipment and your Liebert MP Advanced Power Strip or Access Server.

If you have questions about the power supply connections, contact your local Liebert

representative or Liebert Technical Support at 1-800-222-5877.

CAUTION

Shut down and unplug all equipment in your rack enclosure before beginning to connect the

equipment to your Liebert MP Advanced Power Strip or Access Server.

Summary of content (6 pages)

PAGE 1
LIEBERT MP™ ADVANCED POWER STRIPS QUICK-START GUIDE: OPENCOMMS EM OR MP ADVANCED ACCESS SERVER SAVE THESE IMPORTANT SAFETY INSTRUCTIONS This manual contains important safety instructions. Read all safety, installation and operating instructions before installing the Liebert MP Advanced Power Strip or Access Server. Adhere to all warnings on the unit and in this manual. Follow all operating and user instructions. Individuals without previous training can install and operate this equipment.
PAGE 2
When connecting the rack equipment to the Liebert MP Advanced Power Strip’s receptacles, arrange cables and connections to avoid tangling and crisscrossing the power cables. For power management purposes, record the receptacle where each piece of equipment is connected. Receptacles on the Liebert MP Advanced Power Strip have a numerical designation. Liebert MP Advanced Power Strips with more than one circuit are named with numbers and letters.
PAGE 3
ASSIGN AN IP ADDRESS NOTE These steps must be done on the same network segment where the OpenComms EM is connected. If your network uses static IP addresses and your computer has a Windows operating system, follow the steps below. Otherwise, consult the OpenComms EM user manual (SL-28210). 1. Obtain an IP address for the OpenComms EM from your network administrator. 2. Insert the OpenComms EM CD in your computer’s CD drive. 3. Click on the Start button, then on Run, then Browse to the file IPSET.
PAGE 4
CONFIGURATION WITH LIEBERT MP ADVANCED ACCESS SERVER Liebert MP Advanced Power Strip (MP-C5120) Mounting Bracket on either side EIA-232 POWER 1 3 5 8 EIA-232 Port 2 4 6 8 EIA-232 Port - Connect to Power Strip EIA-232 Port MP-DS74 Card With Configurable Communication Ports Ethernet Port Liebert MP Advanced Access Server (MP-S5138) 100-240VAC ?????????? 0.21-0.
PAGE 5
SET THE IP ADDRESS 1. Select “1” to set the IP Address for Module 1. Enter an IP address (below). The address must be unique on your system (obtain this from your network administrator). 2. Press Enter to return to the Network Port Configuration menu. Enter IP address 3. Choose “2” to set the Subnet Mask for your system (obtain this from your network administrator). SET THE GATEWAY ADDRESS 1.
PAGE 6
Liebert Corporation 1050 Dearborn Drive P.O. Box 29186 Columbus, OH 43229 Telephone: 1-800-877-9222 Facsimile: 1-614-841-6022 www.liebert.com © 2006 Liebert Corporation All rights reserved throughout the world. Specifications subject to change without notice. ® Liebert and the Liebert logo are registered trademarks of Liebert Corporation. All names referred to are trademarks or registered trademarks of their respective owners. SL-20812 (01/06) Rev.