Installation Instructions For NoFrost Combined Refrigerator-Freezers with IceMaker CBS 1360 7085 549-00
Important Please Read and Follow these Instructions These instructions contain Danger, Warning and Caution notes. This information is important for safe and efficient installation and operation. Always read and comply with all Danger, Warning and Caution notes! DANGER! Danger indicates a hazard which will cause serious injury or death if precautions are not followed. WARNING! Warning indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Safety Disposal of Old Appliance DANGER! Risk of child entrapment. Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous – even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents. Electrical Safety Connect this appliance to a 15 amp or 20 amp, 110120 VAC, circuit which is grounded and protected by a circuit breaker or fuse.
Planning Information Appliance Dimensions Overall height of the appliance can be increased by a maximum of 5/8” (see Leveling the appliance).
Planning Information Cabinet Opening Dimensions The appliance can be used freestanding or semi built-in. If semi built-in, please consider the cabinet opening dimensions. This is where the power cord extends from the back of the appliance. The water line lead out position can be within the shaded area. Free length of the power cord = 98 inch (2500 mm). IMPORTANT Do not install the shut-off valve behind the appliance.
Installation Unit Venting Leveling the Appliance Do not restrict the air flow. The ventilation opening can either be directly over the appliance , above the cabinet and below the ceiling or through a vent installed in a soffit . 1 2 3 IMPORTANT The clear ventilation cross-section must be at least 31 in² (200 cm²) from the lower ventilation opening right to the upper one. The section below the freezer door and the floor must not be covered.
Blocking For Safety Mounting the anti tipping device WARNING! Tip over hazard! The anti tipping bracket must be mounted to prevent the appliance from tipping when the fully stocked door is opened. IMPORTANT Be sure that there is no plumbing or electrical wiring located in this area which screws or drills could damage. 1. Mark the center of the appliance on the back wall. 2. Mount the anti tipping bracket. Center line of appliance.
Ice Maker Safety Instructions and Warnings • Do not install the water connection while the combined refrigerator-freezer is connected to an electrical outlet. • The connection to the water supply may only be made by a trained and licensed plumber. • All equipment and devices used to supply the water to the appliance must comply with the current regulations for your geographical area. WARNING! Water Connection Adapter IMPORTANT Only use the supplied adapter for connection to the solenoid valve.
Ice Maker Connection to the Water Supply 1. Move the appliance towards the final position and leave enough space to work behind. 2. Remove the cover from the solenoid valve. 5. Screw the adapter onto the solenoid valve. 6. Move the power supply line to the area of the electrical outlet. WARNING! 3. Connect the water line to the adapter in the respective configuration, depending on the type of water line used. The figure shows the configuration with a copper line as an example.
Reversing Door Hinges Changing Over Door Hinges Door hinges should only be changed by a trained expert. Changing over the door hinges requires two people. 1. Open top door, pry off door cover and pivot to the left. 5. 4. 4. Pull the left-hand side of the cover approx. 1/4" (6 mm) towards you. 1. 5. Remove pin. 2. 3. 2. Let door cover hang down. 3. Slide red safety bracket over the hinge. 6. 6. Open top door wide and remove covers. 7.
Reversing Door Hinges IMPORTANT The door must now be held secure by another person. 9. 13. 8. 8. Disconnect the connector and pull the cable out of the guide. 13. Open bottom door, pry off door cover. 9. Remove cover from upper door mounting and unscrew door. 15. 16. 11. 10. 14. 14. Pivot door cover to the left. 10. Transfer fastener for soft stop mechanism to the opposite side. 15. Slide red safety bracket over the hinge. 16. Remove pin. 11. Transfer cover plate to the opposite side. 12. 17. 17.
Reversing Door Hinges IMPORTANT The door must now be held secure by another person. 25. 18. 19. 26. 18. Pull out middle hinge pin. 19. Remove bottom door. 24. 24. Tilt appliance slightly backwards and unscrew the adjustable foot. 25. Remove the hinge pin. 26. Unscrew hinge bracket. 20. 21. 180° 22. 20. Unscrew hinge bracket. 21. Transfer cover plate to the opposite side. 27. Transfer fastener for soft stop mechanism on hinge bracket to the opposite side. 27. 28.
Reversing Door Hinges 36. 35. Both doors 31. 35. Remove screw. 31. Tilt appliance slightly backwards, insert pin and attach using the adjustable foot. 36. Pivot soft stop mechanism outwards on the left, pull to the left and remove. 32. 33. 32. Release pressure plates at the front 1 and pull them backwards to remove 2. 33. Transfer door handle and plugs to the opposite side. Both doors 33. 34. 34. Transfer panels of both door covers to the opposite side. 37. 37.
Reversing Door Hinges 39. 44. 44. Click cover into place. 39. Insert middle hinge pin. 46. 45. 45. Disconnect the connector. 40. 40. Slide door cover over soft stop mechanism hinge. 46. Using a screwdriver, push out the hinge from underneath and remove it from the door complete with the cable. 47. 41. 42. 47. Using a screwdriver, push out the plug from underneath and transfer it to the opposite side. 43. 41. Move soft stop mechanism hinge to the fastener and insert pin. 48. 49. 42.
Reversing Door Hinges 56. 50. 57. 55. 55. Pull the right-hand side of the cover approx. 1/4" (6 mm) towards you. 50. Suspend top door on hinge pin. For this, the door must be open at least 90°. 56. Move soft stop mechanism hinge to the fastener and insert pin. 57. Remove red safety bracket. IMPORTANT The door must now be held secure by another person. 51. 58. 58. Pivot door cover to the left and click into place on the door. 52. 59. 51. Secure door with screws and click cover into place. 52.
For Service in the U.S. Liebherr Service Center Toll Free: 1-866-LIEBHER or 1-866-543-2437 Email: Service-appliances.us@liebherr.com PlusOne Solutions, Inc. 3501 Quadrangle Blvd, Suite 120 Orlando, FL 32817 For Service in Canada Liebherr Service Center Toll Free: 1-888-LIEBHER or 1-888-543-2437 www.euro-parts.ca EURO-PARTS CANADA 39822 Belgrave Road Belgrave, Ontario, N0G 1E0 Phone: (519) 357-3320 Fax: (519) 357-1326 *708554900* w w w. l i e b h e r r - a p p l i a n c e s .
