Use and Care Manual

-
Follow all Federal, State and local electrical, fire and
building codes and ordinances when installing the
receptacle and / or the appliance.
-
In some communities, a wall switch is required to turn
power to the appliance ON and OFF.
-
To reduce the risk of fire, electric shock, or personal
injury, installation work and electrical wiring must be
done by a qualified electrician in accordance with all
applicable codes and standards, including fire-rated
construction.
-
The socket must be easily accessible so that the appli-
ance can be disconnected from the mains quickly in an
emergency. It must not be behind the back of the appli-
ance.
4.11 Switching on the appliance
Note
u
To switch on the entire appliance, only the freezer
compartment needs to be switched on.
Switch on the appliance 2 hours before loading
with frozen food for the first time.
Do not load frozen foods until the temperature
display reads 0 °F (-18 °C).
4.11.1 Switching on the freezer compart-
ment
u
Press On/Off button, freezer compartment Fig. 3 (13) .
w
The fridge compartment temperature display shows the
current temperature in the interior.
w
The freezer compartment temperature display and the
Alarm symbol will flash until the temperature is cold
enough. If the temperature is greater than 32 °F (0 °C),
flashing dashes will appear; if the temperature is lower
than this, the current temperature will flash on the
display.
w
Whenever "DEMO" appears on the display, the appli-
ance is running in demonstration mode. Contact the
customer service department.
4.11.2 Switching on the fridge compartment
u
Press Fridge compartment On/Off button
Fig. 3 (3) .
w
The interior light comes on when the door is opened.
w
The temperature display flashes. The fridge compart-
ment is switched on.
5 Operation
5.1 Temperature display unit
The temperature display can be changed from °F to °C.
5.1.1 To change the unit
u
Activate setting mode: Press SuperFrost button
Fig. 3 (14) for about 5 seconds.
w
S is displayed in the temperature display.
w
The Menu symbol Fig. 3 (19) lights up.
u
Using Freezer compartment Up button
Fig. 3 (11) / Freezer compartment Down button
Fig. 3 (12) select °.
u
To confirm: Briefly press SuperFrost button
Fig. 3 (14) .
u
Using Freezer compartment Up button
Fig. 3 (11) / Freezer compartment Down button
Fig. 3 (12) select °F or °C.
u
To confirm: Briefly press SuperFrost button
Fig. 3 (14) .
u
To exit setting mode: Press Freezer compartment
On/Off button Fig. 3 (13) .
-or-
u
Wait 5 minutes.
w
The temperature is again displayed in the temperature
display.
5.2 Brightness of the temperature
display
You can adapt the brightness of the temperature display
to the light conditions in the room in which it is installed.
If the door is open or the control panel is used the temper-
ature indicator lights up at maximum brightness. About 1
minute after the door is closed or no button has been
pressed on the control panel, the temperature display
goes back to the set brightness.
5.2.1 Setting the brightness
The brightness can be set between h0 (minimum lumi-
nosity) and h5 (maximum luminosity).
u
To activate setting mode: Press SuperFrost button
Fig. 3 (14) for about 5 seconds.
w
S is shown on the display.
w
The Menu symbol
Fig. 3 (19) lights up.
u
Press Freezer compartment Up button Fig. 3 (11) or
Freezer compartment Down button Fig. 3 (12) to select
h.
u
To confirm: Briefly press SuperFrost button Fig. 3 (14) .
u
To set the display brighter: Press Freezer
compartment Up button Fig. 3 (11) .
u
To set the display darker: Press Freezer
compartment Down button Fig. 3 (12) .
u
To confirm: Press SuperFrost button
Fig. 3 (14) .
w
The brightness is set to the new value.
u
To deactivate setting mode: Press Freezer compart-
ment On/Off button Fig. 3 (13) .
-or-
u
Wait 5 minutes.
w
The temperature is again displayed in the temperature
display.
Operation
17