Installation Instructions Refrigerators and freezers, built-in R 1410/ RB 1410/ F 1051 280815 7084602 - 02
General safety information Contents - The socket must be easily accessible so that 1 General safety information........................... 2 2 Setting up the appliance............................... 2 3 Planning information..................................... 4 4 Cabinet Opening Dimensions...................... 7 5 Air circulation in the kitchen cabinet........... 7 6 Door swing clearance................................... 8 7 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.
Setting up the appliance NOTICE Risk of damage caused by condensation Installing the appliance next to any other refrigerator or freezer can cause condensation or damage to the Liebherr appliance. u Do not install this appliance next to any other refrigerator or freezer except another Liebherr model. Liebherr models are designed to allow side-by-side installation. They are equipped with a heating system to eliminate condensation when refrigerators or freezers are installed side-by-side.
Planning information 3 Planning information unit installation 4 Fig.
Planning information Fig. 2 Side-by-side installation: SBS 241, SBS246, SBS 243 Fig.
Planning information Fig. 4 Side-by-side installation: SBS 246 and SBS 241 with 80” or 84” ventilation grille Fig.
Cabinet Opening Dimensions 4 Cabinet Opening Dimensions Fig. 7 Side-by-side installation: The door must be able to be opened at least 90° to allow the drawers to be pulled out properly. If the door opening angle is 90° it may be difficult to remove the drawers due to the door racks. If the appliance will be installed in a corner please leave a gap of at least 3-3/4 in. (95 mm) from the wall. Fig.
Door swing clearance Fig. 8 - An effective ventilation cross-section of at least 31 in2 (200 cm2) per unit must be present at the air intake Fig. 8 (1) and air outlet Fig. 8 (2). - The upper ventilation cross-section can be set up directly above the appliance with an optional ventilation grille Fig. 8 (2), near the ceiling above a cabinet Fig. 8 (3) or as an air vent in an intermediate ceiling Fig. 8 (4). Fig. 9 - There must be an air shaft (unobstructed) with a minimum depth of 1-1/2 in.
Door swing clearance Fig.
Door swing clearance Fig.
Door swing clearance Fig.
Door swing clearance Fig.
Changing the door hinges 7 Changing the door hinges You can reverse the door hinges, if necessary: Make sure you have the following tools on hand: q Torx 25 q Torx 15 q Screwdriver q Cordless screwdriver, if necessary q Another person to help with the installation, if necessary 7.1 Remove soft stop mechanism (top) WARNING Risk of injury if the soft stop mechanism contracts! If the locking device is not fitted, the soft stop mechanism contracts during disassembly and can jam your fingers.
Changing the door hinges NOTICE Risk of damage! If the door seal is damaged the door may not close properly and the level of cooling is insufficient. u Do not damage the door seal with the screwdriver! u Release panel Fig. 18 (1) using slotted screwdriver and remove. w The panel hangs above the damper bracket. Fig. 20 u Close the door. u Pull cover Fig. 20 (10) forward and then upwards to remove. u Lift off cover Fig. 20 (11). Fig. 19 u Push panel forward over the damper bracket Fig.
Changing the door hinges u Unscrew bearing part Fig. 21 (28), turn it 180° and tighten Fig. 21 (29). u Remove the bearing pin Fig. 21 (27), move it to the other side along with the bearing disc and bearing ring Fig. 21 (26) and secure tightly to 3 lb-ft (4 Nm) . u Using a cordless screwdriver if necessary, tightly secure Fig. 21 (21) the bearing bracket Fig. 21 (20) on the new hinge side again by applying a screw torque of 3 lb-ft (4 Nm) . First fit the lower center screw, then the other screws. 7.
Water connection 7.8 Fitting soft stop mechanism (top) u Snap panel Fig. 26 (1) into place on the door. u Turn cover Fig. 16 (6) 180° from the handle side, place it on top from the outside and snap into place. 7.9 Aligning the door u Unscrew center screw on lower part of bearing bracket Fig. 21 (20). u Align the doors flush with the appliance housing using the two oblong holes in the lower bearing bracket Fig. 21 (20) as a guide if needed. Fig. 25 u Loosen cover Fig. 25 (9) from the panel Fig.
Anti-tip device - All devices and equipment used to supply water must comply with the regulations in force in the respective country. - The solenoid valve is located at the bottom of the back of the appliance. It has a metric R3/4 connecting thread. 9 Anti-tip device The screws for fastening the anti-tip device are not supplied with the appliance. Appropriate screws must be used for the material (wood, concrete, etc.) in which the safety device is mounted.
Single unit installation Fig. 32 Fig. 29 The accessories kit 9900302 may be required depending on the height of the recess. (see 4) u Fit retaining plate Fig. 32 (1) to the lower part of the handle side by inserting two screws Fig. 32 (2) into the pre-cut holes. u Slide installation strip Fig. 32 (3) into the retaining plate Fig. 32 (1) from above. u Push second retaining plate Fig. 32 (4) onto the installation strip Fig. 32 (3) from above and screw to the center of the side wall.
Single unit installation u Position ventilation grille Fig. 33 (10) over the installation contour Fig. 33 (5) and align it such that the holes in ventilation grille and installation contour are above each other. u Screw ventilation grille Fig. 33 (10) to installation contour Fig. 33 (5)from below using three screws Fig. 33 (11). Install end strip: NOTICE* Risk of damage due to leaking water! u When pushing the appliance into the recess ensure that the water connection does not kink or become damaged. Fig.
Side-by-side installation Fig. 39 Fig. 37 If a water filter is used: u Insert water filter (see 13) .* If no water filter is used: u Fit lower ventilation grille Fig. 37 (32) flush with the floor such that the rubber lip is at the top. It is held in place via magnets. u If necessary set the door opening angle (see 12) . 11 Side-by-side installation The appliance with the ice maker must be on the left when viewed from the front, the refrigerator unit on the right.
Side-by-side installation Fig. 44 u Glue spacer Fig. 44 (72) onto the lower part of the side wall on the handle side, approximately 1.5 in. (40 mm) as measured inwards from the front edge of the appliance. Fig. 45 Fig. 42 u Position the appliances next to each other with a gap of approximately 13/32 '' (10 mm) such that they are flush at the front. u Open the door. NOTICE Risk of damage to the castors.
Side-by-side installation Fig. 48 Fig. 46 u Secure upperconnecting element Fig. 46 (11) using two screws Fig. 46 (12). Make preliminary holes (optional) or use a cordless screwdriver. u Clip on cover panel Fig. 46 (13). u Push appliances together at the bottom and realign if necessary. u Insert long carriage bolt Fig. 48 (73). u Push washer Fig. 48 (74) and nut Fig. 48 (75) onto the screw. Tighten nut until the spacer Fig. 48 (72) is touching the opposite side wall. u Fit strip Fig.
Side-by-side installation Fig. 50 u Open the door. u Position end strip Fig. 50 (30) over the installation contour Fig. 42 (14) and align it such that the holes in ventilation grille and installation contour are above each other. u Screw end strip Fig. 50 (30) to installation contour from below using four screws Fig. 50 (31). Secure side installation strip: Fig. 52 Fig. 51 u Remove adhesive tape from the side installation strip Fig. 51 (3). u Push installation strip Fig.
Adjusting the door opening angle u Release panel Fig. 54 (1) using slotted screwdriver and remove. w The panel hangs above the damper bracket. Fig. 53 If a water filter is used: u Insert the water filter (see 13) .* If no water filter is used: u Fit lower ventilation grille Fig. 52 (54) flush with the floor such that the rubber lip is at the top. It is held in place via magnets. u If necessary set the door opening angle (see 12) .
Installing the water filter Fig. 57 u Fit opening limiter (90°) Fig. 57 (21) supplied: insert it into the soft stop mechanism from the side and push in until it audibly snaps into place. Re-attaching the soft stop mechanism: u Hook panel Fig. 59 (1) into the damper bracket Fig. 59 (4) such that the detent hooks are pointing inwards and the front side is facing the appliance. u Push on cover Fig. 59 (5) from the outside (A) and pivot over the bearing part Fig. 59 (8) (B). u Place cover Fig.
Connecting the appliance NOTICE Leakage water may damage the system! u Do not install this system on hot water lines. The maximum operating temperature of the water in this system is 100 °F (37.7 °C). u This system MUST be installed and used in compliance with federal and local installation regulations. u Do not install under water hammer conditions. A water hammer arrestor must be used to prevent water hammering. If you are unsure how to check these conditions, consult a professional installer.
Connecting the appliance - The Power Plug must be easily accessible so that the appliance can be disconnected from the mains quickly in an emergency. It must not be behind the back of the appliance. - The top of the electric outlet must be located within 82-5/8 in. (2100 mm) from the top of the base in the cabinet.
For Service in the U.S.: Liebherr Service Center Toll Free: 1-866-LIEBHER or 1-866-543-2437 Service-appliances.us@liebherr.com PlusOne Solutions, Inc. 3501 Quadrangle Blvd, Suite 120 Orlando, FL 32817 For Service in Canada: Liebherr Service Center Toll Free: 1-888-LIEBHER or 1-888-543-2437 www.euro-parts.ca EURO-PARTS CANADA 39822 Belgrave Road Belgrave, Ontario, N0G 1E0 Phone: (519) 357-3320 Fax: (519) 357-1326 www.liebherr-appliances.com Part No.
