Operating instructions Commercial freezer Read the operating instructions before switching on for the first time Page 14 GB 7082 263-01 GGPv
Content Description of the appliance.................................................... 14 Safety instructions and warnings............................................ 15 Disposal notes......................................................................... 15 Noise emissions from the appliance....................................... 15 Range of appliance use........................................................... 16 Climate rating........................................................................
Safety instructions and warnings • To prevent injury or damage to the unit, the appliance should be unpacked and set up by two people. • In the event that the appliance is damaged on delivery, contact the supplier immediately before connecting to the mains. • To guarantee safe operation, ensure that the appliance is set up and connected as described in these operating instructions. • Disconnect the appliance from the mains if any fault occurs. Pull out the plug, switch off or remove the fuse.
Range of appliance use The appliance is suited only for cooling food. The appliance is not suited for storing and cooling pharmaceuticals, blood plasma, laboratory preparations or similar substances and products subject to the Medical Devices Directive 2007/47/EC. Any misuse of the appliance may result in damage to or spoilage of the stored goods. Furthermore, the appliance is unsuited for use in areas exposed to an explosion hazard.
GB Equipment GGPv 1490 Safety lock GGPv 6590 The lock is equipped with a safety mechanism. Locking the appliance • Insert the key as shown by arrow 1. • Turn the key 180° (2). To unlock the appliance, the same procedure must be repeated in the same order. GGPv 1490 equipment 1 Insert the grid shelves. 2 Install the foot pedal opener. Fit the supplied shelf rails to the right and left of the vertical bar.
Operating and control elements Setting the language Note: the preset language is English. If this is the language which should remain, the following procedure is not necessary.
GB Main menu Press the Menu 04 Programs = preset storage programs button. Use buttons and to select one of the menu items. Menu 01 Setpoint = setting the temperature If the appliance is to be used for special purposes, different storage programs can be set. The storage climate inside the appliance will then be adjusted to the intended use (temperature, humidity).
Menu 05 Alarm = list of alarms The alarm events are saved and can be called up if required. Calling up the saved alarm events The following alarm can be rectified immediately: Door Open Temp. - - °C When the door is open, the above indication and the standard indication flash alternately. After 240 seconds, the audible warning signal sounds. Cancel the audible warning signal by pressing button the appliance door. . Close The following alarm events require the stored items to be checked: 1.
GB Menu 06 Settings = settings on the control electronics Settings 06 Display Settings 01 Service These settings can only be carried out by the customer service department. Settings 02 Language Setting the display language. See paragraph "Setting the language". Settings 03 Clock Setting Setting the time and date. Setting for permanent display light.
Product sensor (available accessory) The temperature may be measured or recorded at any point in the interior using the product sensor. Remove the plug! 1. Feed the sensor through the opening in the compressor compartment and position inside the appliance. Seal the opening with sealant. 2. Undo the screw on the underside of the front panel. Tilt the front panel upwards. Product sensor settings • Connect the appliance to the mains - the display reads OFF.
GB Adjusting the alarm delay > A14= 0 Min. P Alarm Delay > A14= Use buttons and Save by pressing the Cleaning the dust filter Clean the dust filter at least twice per year! Remove the plug! 0 Min. 0 Min. flashes 1. Remove the dust filter by lifting upwards. to select the desired setting. 2. Clean the dust filter with water and detergent. button. 3. Reinstall the dust filter. Return to the standard indication by pressing the button.
Changing over door hinges GGPv 6590 Door hinges should only be changed by a trained expert. Changing the door hinges must be done by two people. 4. Remove the hinge components from the hinge bracket. Bearing ring Brass washer Hinge bushing 1. Open door by about 90°. Important note The door must be opened 90° before the lower hinge bracket is removed. This will hold the self-closing mechanism that is integrated into the door in the required position for installation.
GB 8. Keeping door open at 90°, suspend in top square pin. WARNING! It is essential that the door is open at an angle of 90° during installation. If the door is installed in the closed position, this will lead to destruction of the self-closing mechanism on the first opening and closing of the door. Important As a result of its heavy weight, the door must be held secure by one person. 11. Screw hinge bracket into place. Installation of the foot pedal opener for the lefthand hinged door 9.