Design Guide Fully Integrated Models 24" and 48" Release 07 2015
Welcome Liebherr is one of the World’s leading Manufacturers of Premium Refrigeration. For more than 60 years, Liebherr has specialized in developing and manufacturing first class refrigerators and freezers as well as wine cabinets. We focus on performance and efficiency as well as keeping food fresher longer. Produced in Austria and Germany, Liebherr has a full line of premium models tailored specifically for the North American marketplace to fit any design vision you have for your kitchen.
Introduction LIEBHERR WARRANTY PLAN FULL TWO YEAR WARRANTY - For two years from the date of original purchase, your Liebherr Warranty covers all parts and labor to repair or replace any part of the product which proves to be defective in materials or workmanship. FULL FIVE YEAR WARRANTY - For five years from the date of original purchase, your Liebherr Warranty covers all parts and labor to repair or replace any components that prove to be defective in materials or workmanship in the sealed system.
Contents General Remarks I. Safety Warnings........................................................................................................................................ 7 II. Electrical Requirements & Safety........................................................................................................... 8 III. IceMaker (if equipped)............................................................................................................................ 8 IV. Area Requirements.........
General Remarks I. Safety Warnings PLEASE READ AND FOLLOW THESE INSTRUCTIONS This design guide contains Warning and Caution statements. This information is important for safe and efficient installation. This design guide is not replacing the use and care manual which contains important information on how to use Liebherr appliances. Always read and follow all Warning and Caution statements! indicates a hazardous situation, which if not avoided, will result in death or serious injury.
General Remarks II. Electrical Requirements & Safety III. IceMaker (if equipped) Circuit has to be grounded and protected by a circuit breaker or fuse. Single installation: Side-by-side installation: • 115 volt • 115 volt • 60 hz • 60 hz • 15 amp • 20 amp The icemaker is located in the freezer compartment. The appliance must be level for the icemaker to function properly. If you have hard water, we recommend you install a water softener.
General Remarks IV. Area Requirements V. Safety Regulations Verify the following: • Floors can support refrigerator’s weight plus approximately 1200 pounds (544 kg) of food weight. Not all Liebherr products are designed for 1200 pounds (544 kg) of food. Some units are smaller and total weights may vary. The appliance complies with UL250 and CAN/CSA-C 22,2 No. 63-93 (HF 851, HRB 1110) and respectively CAN/CSA-C22.2 No.
Fully Integrated 24" Model: HC 1030, HC 1050B, HC 1070, HC 1080, HC 1021/ HCB 1060, SBS 6613 24" Model: HC 1030, HC 1050B, HC 1070, HC 1080, HC 1021/ HCB 1060, SBS 6613 Integrated units are the most stylish option available - they're totally out of sight, fully concealed behind a cabinet door. Installed in a tall kitchen cupboard, the refrigerator door simply opens in unison with the cupboard door. HC 1030 Energy Star: certified Energy consumption p. a.
Fully Integrated 24" Model: HC 1030, HC 1050B, HC 1070, HC 1080, HC 1021/ HCB 1060, SBS 6613 HC 1070 Energy Star: certified Energy consumption p. a.
Fully Integrated 24" Model: HC 1030, HC 1050B, HC 1070, HC 1080, HC 1021/ HCB 1060, SBS 6613 HC 1021 Energy Star: certified Energy consumption p. a.: 395* kWh respectively 395** kWh Energy Supply: 115V/60Hz Total capacity: 9.39 cu ft (266 L) Refrigerator: 6.
Fully Integrated 24" Model: HC 1030, HC 1050B, HC 1070, HC 1080, HC 1021/ HCB 1060, SBS 6613 SBS 6613 (HC1021 & HCB 1060) Energy Supply: 115V/60Hz Total capacity: 18.10 cu ft (513 L) Refrigerator: 10.90 cu ft (309 L) BioFresh: 2.4 cu ft (68 L) Freezer: 4.8 cu ft (132 L) Ice cube capacity: 1.7 lb/24h Ice cube stock: 3.
Fully Integrated 24" Model: HC 1030, HC 1050B, HC 1070, HC 1080, HC 1021/ HCB 1060, SBS 6613 Ventilation Requirements This is a fully integrated refrigerator-freezer which means that it is fully enclosed by a kitchen cabinet. This type of cabinet must be carefully constructed using the correct dimensions and it must provide suitable ventilation to ensure proper appliance operation. NOTICE If the following ventilation dimensions are not observed the compressor will be damaged.
Fully Integrated 24" Model: HC 1030, HC 1050B, HC 1070, HC 1080, HC 1021/ HCB 1060, SBS 6613 Kitchen Cabinet Base Grille Location Of The Electrical Outlet Ventilation through the cabinet base at the bottom can be achieved by installing the provided ventilation grille (3) or via a ventilation opening of at least 31 in.² (200 cm²). When using the provided ventilation grille (3), please proceed as follows: - In the cabinet base, cut out a ventilation opening that is 1723/32 in.
Fully Integrated 24" Model: HC 1030, HC 1050B, HC 1070, HC 1080, HC 1021/ HCB 1060, SBS 6613 Unit Dimensions A 21-7/16" (544 mm) B 69-11/16" (1770 mm) C 22" (559 mm) D 69-3/4" - 70-3/8" (1772 - 1788 mm) E min 22" (560 mm) max 22-3/4" (578 mm) G 21-5/8" (550 mm) H 1-5/8" (40 mm) J 27-3/8" (695 mm) K 24-3/4" (629 mm) L max.
Fully Integrated 24" Model: HC 1030, HC 1050B, HC 1070, HC 1080, HC 1021/ HCB 1060, SBS 6613 Kitchen Cabinet Doors Designing the Kitchen Cabinet Doors You will need two doors for the kitchen cabinet, one on top for the refrigerator compartment, and one on the bottom for the freezer compartment. In general, the doors have these characteristics: • The width of the cabinet doors depends on the kitchen style and the size of the gaps between the door panels of the cabinetry.
Fully Integrated 24" Model: HC 1030, HC 1050B, HC 1070, HC 1080, HC 1021/ HCB 1060, SBS 6613 Definition of the Door Panel Heights 1. Start with the lower door of the freezer compartment: The freezer door height is 24-24/32" (629 mm). In order to cover the lower part of the appliance, increase the height of the panel to 27-3/8" (695 mm). 2. To cover the face side of the floor board (a) add the thickness of the floor board (usually 3/4" (19 mm)).
Fully Integrated HC 1030, HC 1050B, HC 1070, HC 1080, HC 1021/ HCB 1060, SBS 6613 HC 1030, HC 1050B, HC 1070, HC 1080, HC 1021/ HCB 1060, SBS 6613 (The numbers in brackets are mm) Cabinet Doors Appliance (a) The base of the cabinet can be thickened to raise the the top of the lower door panel to counter height. Lower panel will have to be increased in length by the same amount. The gap between refrigerator and freezer door must lie within the crosshatched area.
Fully Integrated HC 1030, HC 1050B, HC 1070, HC 1080, HC 1021/ HCB 1060, SBS 6613 Kitchen cabinet setup for the water filter The water filter module can be purchased from your Liebherr retailer or distributor for the models HC 1050B, HC 1080 and HCB 1060. It should be installed near the appliance in the cabinet, for example, in the adapter cabinet above the appliance.
Fully Integrated HC 1030, HC 1050B, HC 1070, HC 1080, HC 1021/ HCB 1060, SBS 6613 21
Fully Integrated 24" Model: HC 1000B, HC 1001B 24" Model: HC 1000B, HC 1001B Integrated units are the most stylish option available - they're totally out of sight, fully concealed behind a cabinet door. Installed in a tall kitchen cupboard, the refrigerator door simply opens in unison with the cupboard door. HC 1000B Energy Star: certified Energy consumption p. a.
Fully Integrated 24" Model: HC 1000B, HC 1001B 23
Fully Integrated 24" Model: HC 1000B, HC 1001B Ventilation Requirements This is a fully integrated refrigerator-freezer which means that it is fully enclosed by a kitchen cabinet. This type of cabinet must be carefully constructed using the correct dimensions and it must provide suitable ventilation to ensure proper appliance operation. NOTICE If the following ventilation dimensions are not observed the compressor will be damaged. B - Side view Cabinet Refrigerator Kitchen Cabinet Airflow 1.
Fully Integrated Kitchen Cabinet Base Grille 24" Model: HC 1000B, HC 1001B Location Of The Electrical Outlet Ventilation through the cabinet base at the bottom can be achieved by installing the provided ventilation grille (3) or via a ventilation opening of at least 31 in.² (200 cm²). When using the provided ventilation grille (3), please proceed as follows: - In the cabinet base, cut out a ventilation opening that is 1723/32 in. (450 mm) in width and 2-7/32 in. (56 mm) in height.
Fully Integrated 24" Model: HC 1000B, HC 1001B Unit Dimensions A 21-7/16" (544 mm) B 69-11/16" (1770 mm) C 21-1/4" (540 mm) D 69-3/4" - 70-3/8" (1772 - 1788 mm) E min 22" (560 mm) max 22-3/4" (578 mm) G 21-5/8" (550 mm) H 1-5/8" (40 mm) J 26-3/8" (669 mm) K 24-3/4" (629 mm) L max. 3/4" (19 mm) M 6-11/16" (170 mm) 1 Power cord 2 Level 3 Fish line for power cord 4 3" of the cabinet needs to be finished as it can be seen when th door is open.
Fully Integrated 24" Model: HC 1000B, HC 1001B Kitchen Cabinet Doors Designing the Kitchen Cabinet Doors You will need two doors for the kitchen cabinet, one on top for the refrigerator compartment, and one on the bottom for the freezer compartment. In general, the doors have these characteristics: • The width of the cabinet doors depends on the kitchen style and the size of the gaps between the door panels of the cabinetry. Generally, a 1/8” vertical gap between the cabinet doors is recommended.
Fully Integrated Definition of the Door Panel Heights 1. Start with the lower door of the freezer compartment: The freezer door height is 24-24/32" (663 mm). In order to cover the lower part of the appliance, increase the height of the panel to 26-3/8" (669 mm). 2. To cover the face side of the floor board (a) add the thickness of the floor board (usually 3/4" (19 mm)). Thus, the minimum height of the freezer door panel is: 26-3/8" + 3/4" = 27-1/8" (669 mm + 19 mm = 688 mm) 3.
Fully Integrated 24" Model: HC 1000B, HC 1001B HC 1000B, HC 1001B (The numbers in brackets are mm) Cabinet Doors Appliance (a) The base of the cabinet can be thickened to raise the the top of the lower door panel to counter height. Lower panel will have to be increased in length by the same amount. The gap between refrigerator and freezer door must lie within the crosshatched area.
Fully Integrated 24" and 48" Models: HF 861 / HRB 1120, SBS 70I4 24" and 48" Models: HF 861 / HRB 1120, SBS 70I4 Integrated units are the most stylish option available - they're totally out of sight, fully concealed behind a cabinet door. Installed in a tall kitchen cupboard, the refrigerator door simply opens in unison with the cupboard door. HF 861 Energy Star: certified Energy consumption p. a.: 439 kWh Energy Supply: 115V/60Hz Total capacity: 7.
Fully Integrated 24" and 48" Models: HF 861 / HRB 1120, SBS 70I4 SBS 70I4 (HF 861 & HRB 1120) Energy Supply: Total capacity: Refrigerator: Freezer: Ice cube capacity: Ice cube stock: Climate Rating: Door hinges: 115V/60Hz 18.62 cu ft (528 L) 10.86 cu ft (308 L) 7.76 cu ft (220 L) 1.7 lb/24h 3.
Fully Integrated 24" and 48" Models: HF 861 / HRB 1120, SBS 70I4 Ventilation Requirements This is a fully integrated refrigerator-freezer which means that it is fully enclosed by a kitchen cabinet. This type of cabinet must be carefully constructed using the correct dimensions and it must provide suitable ventilation to ensure proper appliance operation. NOTICE If the following ventilation dimensions are not observed the compressor will be damaged.
Fully Integrated Kitchen Cabinet Base Grille 24" and 48" Models: HF 861 / HRB 1120, SBS 70I4 Location Of The Electrical Outlet Ventilation through the cabinet base at the bottom can be achieved by installing the provided ventilation grille (3) or via a ventilation opening of at least 31 in.² (200 cm²). When using the provided ventilation grille (3), please proceed as follows: - In the cabinet base, cut out a ventilation opening that is 1723/32 in. (450 mm) in width and 2-7/32 in. (56 mm) in height.
Fully Integrated 24" and 48" Models: HF 861 / HRB 1120, SBS 70I4 Unit Dimensions A 21-7/16" (544 mm) B 69-11/16" (1770mm) C 22" (559 mm) D 69-3/4" - 70-3/8" (1772 - 1788 mm) E min 22" (560 mm) max 22-3/4" (578 mm) F 21-5/8" (550 mm) G 1-5/8" (40 mm) J 66-1/2" (1689,9 mm) K max. 3/4" (19 mm) L 9-21/32" (245 mm) 1 Power cord 2 Level 3 Fish line for power cord 4 3" of the cabinet needs to be finished as it can be seen when th door is open.
Fully Integrated 24" and 48" Models: HF 861 / HRB 1120, SBS 70I4 Kitchen cabinet setup for the water filter The water filter module is supplied with the appliance (only available for HF 861). It should be installed near the appliance in the cabinet, for example, in the adapter cabinet above the appliance. To connect the filter to the appliance, it may be necessary to make an opening (C) in the floor of the adapter cabinet through which the hoses will be routed.
Fully Integrated 24" and 48" Models: HF 861 / HRB 1120, SBS 70I4 Kitchen Cabinet Doors Designing the Kitchen Cabinet Door You will need one door for the kitchen cabinet. In general, the door has these characteristics: • The width of the cabinet door depends on the kitchen style and the size of the gaps between the door panels of the cabinetry. Generally, a 1/8 in. (3 mm) vertical gap between the door panels is recommended. • The door should be at least 5/8 in.
Fully Integrated 24" and 48" Models: HF 861 / HRB 1120, SBS 70I4 Definition of the Door Panel Heights 1 Cabinet door 2 Appliance door The height of the cabinet door is calculated as follows: Total cabinet height (i. e., 70-3/8 in. (1788 mm)) plus the thickness of the cover plate and floor plate Fig. 9 (a) (usually 3/4 in. (19 mm)): 70-3/8 in. + 3/4 in. + 3/4 in. = 71-7/8 in.
Design Guide Release 07 2015
