Design Guide 2011 Fully Integrated Models 24" and 48"
Welcome Liebherr's engineering excellence in Germany provides the largest selection of freezers, refrigerators and wine refrigerators worldwide. Liebherr appliances consistently specializes in the manufacturing of high quality freezers and refrigerators. With more than 300 basic models, we have the widest selection in the world. Liebherr appliances feature premium quality, numerous innovative product ideas and advanced design.
Introduction LIEBHERR WARRANTY PLAN FULL TWO YEAR WARRANTY - For two years from the date of original purchase, your Liebherr Warranty covers all parts and labor to repair or replace any part of the product which proves to be defective in materials or workmanship. FULL FIVE YEAR WARRANTY - For five years from the date of original purchase, your Liebherr Warranty covers all parts and labor to repair or replace any components that prove to be defective in materials or workmanship in the sealed system.
Contents General Remarks Safety Warnings I Electrical Requirements & Safety II IceMaker (if equipped) III Area Requirements IV Safety Regulations V Fully Integrated Models 24" and 48" Models HC 1001 / HC 1050, SBS 20H0 HC 1011 / HC 1060, SBS 20H1 1 Ventilation Requirements 3 Kitchen Cabinet Base Grille 4 Unit Dimensions 5 Kitchen Cabinet Doors 6 Definition of the Door Panel Heights 7 HF 851 / H
General Remarks I. Safety Warnings PLEASE READ AND FOLLOW THESE INSTRUCTIONS This design guide contains Warning and Caution statements. This information is important for safe and efficient installation. This design guide is not replacing the use and care manual which contains important information on how to use Liebherr appliances. Always read and follow all Warning and Caution statements! indicates a hazardous situation, which if not avoided, will result in death or serious injury.
General Remarks II. Electrical Requirements & Safety III. IceMaker (if equipped) A 115 Volt, 60 Hz, 15 Amp (20 Amp for side-by-side installation) fused electrical supply is required. Connect an undercounter wine cabinet to a 115 VAC, 10 amp (15 Amp for side-by-side installations) circuit that is controlled by a circuit breaker or fuse. We recommend using a dedicated circuit for these appliances to prevent electrical overload.
General Remarks IV. Area Requirements V. Safety Regulations Verify the following: • Floors can support refrigerator’s weight plus approximately 1200 pounds (544 kg) of food weight. Not all Liebherr products are designed for 1200 pounds (544 kg) of food. Some units are smaller and total weights may vary. The appliance complies with UL250 and CAN/CSA-C 22,2 No. 63 and is designed to cool, freeze, store food as well as make ice (if equipped). It is designed as a household appliance.
Fully Integrated HC 1001/HC 1050 - SBS 20H0, HC 1011/HC 1060 - SBS 20H1, HF 851/HRB 1110 - SBS 19H0 24" and 48" Models: HC 1001 / HC 1050, SBS 20H0 HC 1011 / HC 1060, SBS 20H1 Integrated units are the most stylish option available - they're totally out of sight, fully concealed behind a cabinet door. Installed in a tall kitchen cupboard, the refrigerator door simply opens in unison with the cupboard door. HC 1001 / HC 1011 Energy Star: Energy consumption p. a.
Fully Integrated HC 1001/HC 1050 - SBS 20H0, HC 1011/HC 1060 - SBS 20H1, HF 851/HRB 1110 - SBS 19H0 SBS 20H0 (HC 1001 & HC 1050) Energy Supply: Total capacity: Refrigerator: Freezer: Ice cube capacity: Ice cube stock: Climate Rating: Door hinges: 115V/60Hz/360W 18.6 cu ft (532 L) 14.0 cu ft (400 L) 4.6 cu ft (132 L) 2.2 lbs./24h 3.3 lbs.
Fully Integrated HC 1001/HC 1050 - SBS 20H0, HC 1011/HC 1060 - SBS 20H1, HF 851/HRB 1110 - SBS 19H0 Ventilation Requirements This is a fully integrated refrigerator-freezer which means that it is fully enclosed by a kitchen cabinet. This type of cabinet must be carefully constructed using the correct dimensions and it must provide suitable ventilation to ensure proper appliance operation. B - Side view Kitchen Cabinet Airflow 1.
Fully Integrated HC 1001/HC 1050 - SBS 20H0, HC 1011/HC 1060 - SBS 20H1, HF 851/HRB 1110 - SBS 19H0 Kitchen Cabinet Base Grille Ventilation through the cabinet base at the bottom can be achieved by installing the provided ventilation grille (3) or via a ventilation opening of at least 31 in.² (200 cm²). When using the provided ventilation grille (3), please proceed as follows: - In the cabinet base, cut out a ventilation opening that is 1723/32 in. (450 mm) in width and 2-7/32 in. (56 mm) in height.
Fully Integrated HC 1001/HC 1050 - SBS 20H0, HC 1011/HC 1060 - SBS 20H1, HF 851/HRB 1110 - SBS 19H0 Unit Dimensions 5 A 21-7/32" (539 mm) B 69-21/32" (1769,5 mm) C 21-15/16" (557 mm) D 69-3/4" - 70-3/8" (1772 - 1788 mm) E min 22" (560 mm) max 22-3/4" (578 mm) G 21-21/32" (550 mm) H 1-1/2" (38 mm) J 27-3/8" (695 mm) K 24-3/4" (629 mm) L max. 3/4" (19 mm) M 9-21/32" (245 mm) Follow the distance M to the wall to allow the drawers to be pulled out properly.
Fully Integrated HC 1001/HC 1050 - SBS 20H0, HC 1011/HC 1060 - SBS 20H1, HF 851/HRB 1110 - SBS 19H0 Kitchen Cabinet Doors Designing the Kitchen Cabinet Doors You will need two doors for the kitchen cabinet, one on top for the refrigerator compartment, and one on the bottom for the freezer compartment. In general, the doors have these characteristics: • The width of the cabinet doors depends on the kitchen style and the size of the gaps between the door panels of the cabinetry.
Fully Integrated HC 1001/HC 1050 - SBS 20H0, HC 1011/HC 1060 - SBS 20H1, HF 851/HRB 1110 - SBS 19H0 Definition of the Door Panel Heights: 1. Start with the lower door of the freezer compartment: The freezer door height is 24-24/32" (629 mm). In order to cover the lower part of the appliance, increase the height of the panel to 27-23/64" (695 mm). 2. To cover the face side of the floor board (a) add the thickness of the floor board (usually 3/4" (19 mm)).
Fully Integrated HC 1001/HC 1050 - SBS 20H0, HC 1011/HC 1060 - SBS 20H1, HF 851/HRB 1110 - SBS 19H0 Cabinet Doors Appliance (The numbers in brackets are mm) The gap between refrigerator and freezer door must lie within the crosshatched area.
Fully Integrated HC 1001/HC 1050 - SBS 20H0, HC 1011/HC 1060 - SBS 20H1, HF 851/HRB 1110 - SBS 19H0 24" and 48" Models: HF 851 / HRB 1110, SBS 19H0 Integrated units are the most stylish option available - they're totally out of sight, fully concealed behind a cabinet door. Installed in a tall kitchen cupboard, the refrigerator door simply opens in unison with the cupboard door. HF 851 Energy Star: Energy consumption p. a.
Fully Integrated HC 1001/HC 1050 - SBS 20H0, HC 1011/HC 1060 - SBS 20H1, HF 851/HRB 1110 - SBS 19H0 SBS 19H0 (HF 851 & HRB 1110) Energy Supply: Total capacity: Refrigerator: Freezer: Ice cube capacity: Ice cube stock: Climate Rating: Door hinges: 115V/60Hz/360W 18.4 cu ft (524 L) 10,8 cu ft (307 L) 7,6 cu ft (217 L) 2.2 pd./24h 3.3 pd.
Fully Integrated HC 1001/HC 1050 - SBS 20H0, HC 1011/HC 1060 - SBS 20H1, HF 851/HRB 1110 - SBS 19H0 Ventilation Requirements This is a fully integrated refrigerator-freezer which means that it is fully enclosed by a kitchen cabinet. This type of cabinet must be carefully constructed using the correct dimensions and it must provide suitable ventilation to ensure proper appliance operation. B - Side view Kitchen Cabinet Airflow 1.
Fully Integrated HC 1001/HC 1050 - SBS 20H0, HC 1011/HC 1060 - SBS 20H1, HF 851/HRB 1110 - SBS 19H0 Kitchen Cabinet Base Grille Ventilation through the cabinet base at the bottom can be achieved by installing the provided ventilation grille (3) or via a ventilation opening of at least 31 in.² (200 cm²). When using the provided ventilation grille (3), please proceed as follows: - In the cabinet base, cut out a ventilation opening that is 1723/32 in. (450 mm) in width and 2-7/32 in. (56 mm) in height.
Fully Integrated HC 1001/HC 1050 - SBS 20H0, HC 1011/HC 1060 - SBS 20H1, HF 851/HRB 1110 - SBS 19H0 Unit Dimensions A 21-7/32" (539 mm) B 69-21/32" (1769,5 mm) C 21-15/16" (557 mm) D 69-3/4" - 70-3/8" (1772 - 1788 mm) E min 22" (560 mm) max 22-3/4" (578 mm) F 21-21/32" (550 mm) G 1-1/2" (38 mm) J 66-1/2" (1689,9 mm) K max. 3/4" (19 mm) L 9-21/32" (245 mm) Follow the distance L to the wall to allow the drawers to be pulled out properly.
Fully Integrated HC 1001/HC 1050 - SBS 20H0, HC 1011/HC 1060 - SBS 20H1, HF 851/HRB 1110 - SBS 19H0 Kitchen cabinet setup for the water filter The water filter module is supplied with the appliance. It should be installed near the appliance in the cabinet, for example, in the adapter cabinet above the appliance. To connect the filter to the appliance, it may be necessary to make an opening (C) in the floor of the adapter cabinet through which the hoses will be routed.
Fully Integrated HC 1001/HC 1050 - SBS 20H0, HC 1011/HC 1060 - SBS 20H1, HF 851/HRB 1110 - SBS 19H0 Kitchen Cabinet Doors Designing the Kitchen Cabinet Doors You will need two doors for the kitchen cabinet, one for the refrigerator compartment, and one for the freezer compartment. In general, the doors have these characteristics: • The width of the cabinet doors depends on the kitchen style and the size of the gaps between the door panels of the cabinetry.
Fully Integrated HC 1001/HC 1050 - SBS 20H0, HC 1011/HC 1060 - SBS 20H1, HF 851/HRB 1110 - SBS 19H0 Definition of the Door Panel Heights: 1 Cabinet door 2 Appliance door The height of the cabinet door is calculated as follows: Total cabinet height (i. e., 69-21/32 in. (1769.5 mm)) plus the thickness of the cover plate and floor plate Fig. 9 (a) (usually 3/4 in. (19 mm))/ 69-21/32 in. + 3/4 in. + 3/4 in. = 71-5/32 in. ( 1769.5 mm + 19 mm + 19 mm = 1807.
Design Guide 2011