Installation instructions

6.4 Cleaning the IceMaker*
Fig. 32
The IceMaker has to be switched on.
u
Pull out the drawer and remove the ice cubes.
u
Clean the drawer with warm water and mild washing-up liquid.
u
When the drawer is pulled out, hold down the On/Off button
(about 10 seconds).
w
After about 1 s the LED goes out, the IceMaker is switched off.
w
After about 10 s the LED flashes for about 60 s.
u
Slide in the drawer while the LED is flashing.
w
The ice-cube tray of the IceMaker turns to a skew position.
u
Remove the drawer.
u
Clean the ice cube tray with warm water. If necessary, use mild
washing-up liquid. Then rinse.
Switch the IceMaker on again.
u
Press the ON/OFF button until the LED shines, then slide in
the drawer.
w
The IceMaker starts producing ice cubes.
If washing-up liquid was used:
u
throw away the first three loads of ice cubes to get rid of any
remaining washing-up liquid.
6.5 Customer service
First check whether you can correct the fault yourself by refer-
ence to the list (see Malfunction). If this is not the case, please
contact the customer service whose address is given in the
enclosed customer service list.
WARNING
Risk of injury if repair work is not carried out professionally!
u
Have any repairs to and intervention in the appliance and
mains power cable, which are not expressly mentioned in the
(see Maintenance) carried out by the customer service only.
u
Read the appliance
designation
Fig. 33 (1) , service
No. Fig. 33 (2) and
serial No. Fig. 33 (3) off
the type plate located
inside the appliance
on the left-hand side.
Fig. 33
u
Notify the customer service, specifying the fault, appliance
designation Fig. 33 (1) , service No. Fig. 33 (2) and serial No.
Fig. 33 (3) .
w
This will help us to provide you with a faster and more accurate
service.
u
Keep the appliance closed until the customer service arrives.
w
The food will stay cool longer.
u
Pull out the mains plug (not by pulling the connecting cable)
or switch off the fuse.
7 Malfunction
Your appliance is designed and manufactured for a long life span
and reliable operation. If a malfunction nonetheless occurs
during operation, check whether it is due to a handling error. In
this case you will have to be charged for the costs incurred, even
during the warranty period. You may be able to rectify the
following faults yourself:
Appliance does not work.
→
The appliance is not switched on.
u
Switch on the appliance.
→
The power plug is not properly inserted in the wall socket.
u
Check power plug.
→
The fuse of the wall socket is not in order.
u
Check fuse.
The compressor runs for a long time.
→
The compressor switches to a low speed when little cold is
needed. Although the running time is increased as a result,
energy is saved.
u
This is normal in energy-saving models.
→
SuperFrost is activated.
u
The compressor runs for longer in order to rapidly cool the
food. This is normal.
→
SuperCool is activated.
u
The compressor runs for longer in order to rapidly cool the
food. This is normal.
Excessive noise.
→
Speed-controlled* compressors may produce varying
running noise due to different speed steps.
u
The sound is normal.
A bubbling and gurgling noise.
→
This noise comes from the refrigerant flowing in the refriger-
ation circuit.
u
The sound is normal.
A quiet clicking noise.
→
The noise is produced whenever the refrigeration unit (motor)
automatically switches on or off.
u
The sound is normal.
A hum. It is briefly a little louder when the refrigeration unit
(the motor) switches on.
→
The refrigeration increases automatically when the Super-
Frost, function is activated, fresh food has just been placed
in the appliance or the door has been left open for a while.
u
The sound is normal.
→
The refrigeration increases automatically when the Super-
Cool function is activated, fresh food has just been placed in
the appliance or the door has been left open for a while.
u
The sound is normal.
→
The ambient temperature is too high.
u
Solution: (see 1.2)
Vibratory noise.
→
The appliance is not standing firmly on the floor. As a result,
adjoining units or objects are set into vibration by the running
refrigeration unit.
u
Move bottles and containers apart.
Flow sound at the soft stop mechanism.
→
The noise is produced when the door is opened and closed.
u
The sound is normal.
The temperature display indicates: F0 to F5.
→
There is a fault.
u
Contact the customer service (see Maintenance).
The temperature display indicates: nA
→
The freezer temperature rose too high over the last hours or
days due to a power failure or power interruption. When the
power interruption is over, the appliance will continue to
operate in the last temperature setting.
Malfunction
16