Operation Manual

u
Remove the cover Fig. 6 (27) .*
u
Fully retract the adjustable-height foot Fig. 6 (22) .
u
If necessary, tip the appliance back a little with the assistance
of a second person for removal of the bearing pin.
u
Pull out the bearing pin Fig. 6 (22) downwards and forwards.
In so doing, pay attention to the hinge bush Fig. 6 (20) .
u
Unscrew the turn hinge Fig. 6 (23) (2 Torx 25) Fig. 6 (24) .
u
Unscrew the bearing part Fig. 6 (26) (1 Torx 25), Fig. 6 (28) .
u
Carefully lift off and transfer the cover Fig. 6 (25) on the handle
side.
u
Screw down the turn hinge Fig. 6 (23) on the new hinge side,
possibly with the aid of a cordless screwdriver, through the
outer oblong hole and round hole.
Note
u
If necessary, e.g. to make up for any unevenness in the floor,
the second oblong hole can be used instead of the round hole
for the screw fitting.
u
Tip the appliance back a little
again and re-insert the bear-
ing pin Fig. 7 (22) . The notch
has to point forwards.
u
Place the cover Fig. 6 (27) on
the opposite side.*
Fig. 7
CAUTION
Risk of injury if the door tips!
u
The safety lock (21) has to engage with the turn hinge at the
side so that the bearing pin and therefore the door are se-
cured.
u
u
Snap the safety lock (21) onto the turn hinge again.
u
Put on the hinge bush Fig. 6 (20) .
4.1.5 Transferring the handles
u
Disengage the spring clip Fig. 8 (31) from the upper door and
transfer it to the new hinge side.
u
Lift the stoppers Fig. 8 (30) out of the door bearing bushes and
transfer them.
Fig. 8
u
Detach the door handles Fig. 8 (32) , stoppers Fig. 8 (33) and
pressure plates Fig. 8 (34) and transfer to the opposite side.
u
When fitting the pressure plates at the opposite side, pay at-
tention that they engage properly.
4.1.6 Fitting the lower door
u
Place the lower door from above onto the lower bearing pin
Fig. 6 (22) .
u
Close the door.
u
Place the plastic cap Fig. 5 (10) back onto the middle turn
hinge Fig. 5 (13) .
u
Place the middle bearing pin Fig. 5 (11) in the lower door, on
the new hinge side, through the middle turn hinge Fig. 5 (13) .
4.1.7 Fitting the upper door
u
Place the upper door on the middle bearing pin
Fig. 5 (11) .
u
Insert the upper turn hinge Fig. 4 (3) in the door on the new
hinge side.
u
Screw down the upper turn hinge (2 Torx 25) Fig. 4 (4) . Pos-
sibly make preliminary holes with a bradawl or use a cordless
screwdriver.
u
Apply the cover Fig. 4 (1) and cover Fig. 4 (2) to the opposite
side from the outside and snap them into place.
4.1.8 Aligning the doors
u
Transfer the middle screw of the lower turn hinge
Fig. 6 (23)
into the free oblong hole.
u
If necessary, align the doors to the appliance housing by way
of the two oblong holes in the lower turn hinge Fig. 6 (23) and
middle turn hinge Fig. 5 (13) .
u
Tighten the screws.
4.2 Water connection
WARNING
Danger of electric shock!
u
Disconnect the appliance by unplugging it before you connect
it to the water line.
u
Shut off the water supply before you connect the water feed
lines of the IceMaker.
u
The connection to the drinking water system may be carried
out only by a qualified gas fitter and plumber.
WARNING
Risk of poisoning!
u
The water quality has to comply with the drinking water ordi-
nance of the respective country (e.g. 98/8
u
The IceMaker serves exclusively for making ice cubes in
household quantities and has to be operated with water suit-
able for the purpose.
Putting into operation
5