Installation Instructions For Wine Cooler MW 18.. / MW 24..
Important Table of Contents Page Please Read and Follow these Instructions.................. 2 Note to the Installer......................................................... 2 Important Safety Information.......................................... 3 R600a Refrigerant.......................................................... 4 Disposal of Old Appliance.............................................. 4 Disposal of Packaging Material...................................... 4 Electrical Safety.....................
Safety Important Safety Information • WARNING: Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction. • WARNING: Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer. • WARNING: Do not damage the refrigerant circuit. • WARNING: The power cord must not be damaged while installing the appliance.
Safety • Any repairs and work on the appliance should only be performed by the customer service department or other trained personnel. The same applies to changing the power cord. • Only perform repair and other work on the appliance when the plug has visibly been disconnected. • Only install, connect, and dispose of the appliance as described in this Use and Care Manual. • In the event of a fault, pull out the plug or switch off the fuse.
Safety Electrical Safety Connect this appliance to a 15 amp or 20 amp, 110120 VAC circuit which is grounded and protected by a circuit breaker or fuse. We recommend using a dedicated circuit for this appliance to prevent circuit overload and the chance of interruption to the appliance. This appliance is equipped with a three-prong (grounding) polarized plug for your protection against possible shock hazards.
Planning Information Appliance Dimensions MW 18.. MW 24.. Stated minimum height dimensions include when the levelled feet are fully inserted. Width will increase by 1/4" (6.5 mm) when mounting strips are installed. Door Swing Clearance MW 18.. (top view) MW 24.. Inset installation style A = 8 1/4" (210 mm) B = 1/2" (12.5 mm) C = 19 7/8" (505 mm) Inset installation style A = 10 3/4" (273 mm) B = 1/2" (12.5 mm) C = 25 7/8" (658 mm) Frameless installation style A = 8 1/2" (216 mm) B = 1/2" (12.
Planning Information Cabinet Opening Dimensions Continuous toe kick Individual toe kick A Cabinet depth frameless installation style = 25" (635 mm) Cabinet depth inset installation style = 25" (635 mm) plus panel thickness B This is the point where the power cord exits from the appliance rear. 3/4" (19 mm) from the left and 5" (127 mm) from the floor. Free length of the power cord is 98" (2.5 m).
Planning Information Panel Dimensions 18" recess Inset installation style H = 79 7/8" (2029 mm) W = 17 3/4" (451 mm) H = 58 7/8" (1495 mm) W = 11" (280 mm) Frameless installation style H = 80" (2032 mm) plus overlapping of the panel on the top W = 18" (457 mm) plus overlapping of the panel on both sides Minimum panel thickness = 5/8" (16 mm) Maximum panel thickness = 1" (25 mm) Maximum panel weight = 55 lbs (25 kg) 24" recess Inset installation style H = 79 7/8" (2029 mm) W = 23 3/4" (603 mm) H = 58 7/8" (
Unpacking Unpacking Tx™ 20 1. Cut the straps and remove them. Tx™ 20 2. Press in the lug, tear or cut the carton on the edge and remove it. 3. Remove all styrofoam packing material from the sides and top. MW 18.. anti tipping device 7. Remove the rear transportation safety components and anti-tipping device. MW 24.. 4. Remove the box with mounting parts. Remove the packed cover strips and support strips from the appliance rear. WARNING! Risk of injury and damage. 5. Remove the ventilation grille.
Unpacking Alternative possibility: Tilt the appliance slightly sideways. Cut off the marked area from the pallet. or Slide a two-wheeled cart between the appliance and packaging. Restrain the appliance to the cart with straps. Tilt the appliance onto the cart. Place the appliance carefully on the floor.
Standard Accessories Standard Accessories Ventilation grille Divider for ventilation duct in the toe kick area Top cover for the door panel attachment bracket MW 18.. Retaining screws for installation 8 pcs. 20 pcs. 16 pcs. Tx™ 15 MW 24.. 2 pcs. 10 mm wrench Tx™ 10 or Tx™ 15 22 pcs. MW 18.. 24 pcs. MW 24.. Appliance cover strips for the gap between appliance and recess Depth adjustment aid 4 pcs. Tx™ 15 Door stop SmartDeviceBox Includes component for smartphone connectivity 2 pcs. 2 pcs.
Blocking for Safety Mounting the anti tipping device in cabinets deeper than 24" - Figure 1- 2 To ensure the compressor mounting plate reaches the anti tipping bracket in cabinets deeper than 24", a wooden spacer must be mounted between the appliance back and the wall. The anti tipping bracket will be fastened to the floor downwards and to the spacer backwards. WARNING! Be sure the wooden spacer is fastened securely to the floor.
Blocking for Safety Mounting the anti tipping device on concrete floors - Figure 4 - 5 Secure the appliance in place so it does not tip forward when the fully stocked door is opened. The anti tipping bracket is provided with the appliance. 1. Mark the center line of the appliance on the back wall. Align the anti tipping bracket center to this line. Wall WARNING! Be sure that there is no plumbing or electrical wiring located in this area which screws or drills could damage. 2.
Blocking Safety for Appliance Installation Move the appliance towards the final position and leave enough space to work behind. Route the power cord towards the electrical outlet. IMPORTANT Complete the installation before switching on the device. Tx™ 10 Apply the appliance cover strips to the left and right front edge of the appliance housing, align in height with the top profile and screw into place. The strip is transparent so the designed mounting holes on the appliance housing are visible.
Installation Recess top view Slide the appliance into the recess. Move the power cord and appliance at the same time to avoid damage. Remove the transit supports using the Torx 25 key. DANGER! Risk of death or serious injury due to appliance tipping. Align the appliance in depth. X = Recess front to appliance housing front (not cover strip) Do not open the appliance door before the height adjustment is finished and the antitipping bracket supports the appliance.
Installation Measure the distance. Inset installation style From the bottom of the recess to the center of the attachment bracket boreholes Mount the ventilation grille with the grille segments tilted down. Remove the depth adjustment aid before fastening the appliance in the recess. Frameless installation style From the top of the recess to the center of the attachment bracket boreholes Fasten the appliance in the recess through the appliance cover strips using eight screws 4 x 14 for each side.
Installation Remove the attachment bracket from the door. Nuts are required again later. IMPORTANT Door handles should be mounted now because the side support strips will cover the mounting holes. Only use countersunk screws for handle mounting. Fit the attachment bracket on the panel. Tx™ 15 The holes should be countersunk. The screw heads should be flush with the panel. Fit the divider for the ventilation duct using two screws 4 x 19. Fit cover.
Installation IMPORTANT If the door has to be limited to a 90° opening angle, it must be done before the panel is mounted onto the appliance door. See chapter “Important Note for Changing over Door Hinges or Limiting the Hinges to a 90° Opening Angle” on page 21. Open the appliance door. Place the door panel on the top adjusting bolts and align in the centre. Align the panel in its vertical position if necessary. Loosen the hex nuts and turn the adusting bolts with the Torx 15 key provided.
Installation Align the panel in its depth at the bottom. Loosen the screws, align the panel and tighten the screws. Use the Torx 20 key provided. Fasten the panel through the bottom attachment bracket with two screws 4 x 14. IMPORTANT For installation, only pull out the magnetic seal at one of the marked screw positions (there are 9 on each side 200 mm apart). Never remove the magnetic seal in full.
Installation Adjust the brackets to the thickness of the toe kick panel. Click cover into place. Remove the backing foil and affix the toe kick panel. Check that there is no gap between the appliance air divider and the door air divider. IMPORTANT There will be a gap if the ventilation grille is fitted incorrectly.
Installation Please note in case of removing appliance from the recess If the appliance has to be removed from the recess again, please make sure you take account of the following. 1. Unload the appliance. 2. Disconnect the appliance from the power source. 3. Remove the mounted front panel from the appliance door. 4. Lower the appliance using the height adjustment unit. 5. Mount the transit supports with two screws for each support using a Torx 25 key.
For Service in the U.S. Liebherr Service Center Toll Free: 1-866-LIEBHER or 1-866-543-2437 Email: Service-appliances.us@liebherr.com PlusOne Solutions, Inc. 3501 Quadrangle Blvd, Suite 120 Orlando, FL 32817 For Service in Canada Liebherr Service Center Toll Free: 1-888-LIEBHER or 1-888-543-2437 www.euro-parts.ca EURO-PARTS CANADA 39822 Belgrave Road Belgrave, Ontario, N0G 1E0 Phone: (519) 357-3320 Fax: (519) 357-1326 *708588200* w w w. l i e b h e r r - a p p l i a n c e s .
