Design Guide

36" Monolith Refrigerator
Available Accessories
· Stainless steel door panel
· Monolith brushed aluminum square handle
· Monolith stainless steel round handle
· Monolith brushed aluminum soft-edge handle
· Stainless steel Toe Kick
· Reverse door kit
See pages 42–43 for available accessories
for single units and Side-by-Side combinations.
MRB 3600
* Estimated energy cost will depend on utility rates and use. Estimated energy cost
based on a national average electricity cost of 12 cents per KWh.
** Noise output – according to EN 60704-3.
*** Please contact your Liebherr Authorized Dealer for door reversal.
20 21
36"
Inset
A = 15 3/4" (400 mm)
B = 1/2" (12.5 mm)
C = 37 7/8" (962 mm)
Frameless
A = 16" (406 mm)
B = 1/2" (12.5 mm)
C = 38 3/8" (975 mm)
Dimension A = without
mounted door handle
IMPORTANT!
Stated minimum height dimensions include
when the leveled feet are fully inserted.
Height can be increased by a maximum of
1" (26 mm) by turning the adjust able feet.
When the appliance is fitted in the recess,
the appliance must be raised by turning the
adjustable feet so that the appliance top
has contact with the anti-tipping bracket.
This results in a 4" (102 mm) Toe Kick height.
Product Dimensions
A
Cabinet depth frameless installation style = 25" (635 mm)
Cabinet depth inset installation style = 25" (635 mm) +
panel thickness
B
At this point the power cord exits from the appliance rear.
3/4" (19 mm) from the left and 5" (127 mm) from the
floor. Free length of the power cord is 98" (2.5 m).
C
The appliance has a recess in this area for cable and
waterline laying. 1" (25 mm) in depth and 5 1/2"
(140 mm) in height over the whole width of the appliance.
D
This surface is visible when the appliance door is open.
Designed finish is required.
E1, E2
Depending on the appliance, the anti-tipping bracket is
positioned at the top (E1) or base (E2) of the appliance
and must be secured to the wall or to the floor, please
refer to the installation manual for more information.
36" recess
Inset installation style
H = 79 7/8" (2029 mm)
W = 35 3/4" (908 mm)
Frameless installation style
H = 80" (2032 mm) Add overlapping
dimension to the panel on the top.
W = 36" (914 mm) Add overlapping
dimension to the panel on both sides.
Panel thickness: Min. 5/8" (16 mm)* / Max. 1" (25.4 mm)
Panel and handle weight: Max. 88 lbs. (40 kg)
Individual Toe Kick
Cut out Dimensions
Door Panel Dimensions
and dimensions of free length for power
Continuous Toe Kick
84"
(2134 mm)
4"
(102 mm)
36"
(914 mm)
A
B
13 3
2 /16" - 4
/16"
(72 - 106 mm)
3"
(76 mm)
3"
(76 mm)
DD
C
E1
E2
84"
(2134 mm)
36"
(914 mm)
A
B
3"
(76 mm)
3"
(76 mm)
DD
C
E1
E2
W
H
~
8.8 ft (2400 mm)
~
5 ft (1550 mm)
* If a shaker style panel is used, which is thinner than the minum panel thickness, shorter screws than those supplied in the accessory pack must be used.
C
260
31 *
39 **
18.9 (535)
8.3 (236)
4
3
2 / 1 with LED lighting
InfinitySwipe
+36 °F to +45 °F (+2 °C to +7 °C)
automatic
InfinityLight
InfinitySpring
yes
right, reversible ***
83 3/4" / 35 11/16" / 24"
212.6 / 90.6 / 61
84" / 36" / 25"
213.4 / 91.4 / 63.5
438.7 (199)
115/60
Energy consumption (kWh / y)
Estimated Yearly Energy Cost in US $
Sound rating dB(A)
Refrigerator capacity cu.ft. (l)
BioFresh / BioFresh-Plus comp. cu.ft. (l)
Number of shelves
Number of door racks
Number of BioFresh drawers / BioFresh-Plus drawers
Electronic control
Refrigerator temperature range °F (°C)
Defrost type
Interior light
Internal Water Dispenser
Water fi lter
Door hinges
Product dimensions
in inch H / W / D
in cm H / W / D
Cut out dimensions
in inch H / W / D
in cm H / W / D
Net weight lbs. (kg)
Voltage V / Hz
35
11
/
16" (906 mm)