Operating instructions BioFresh fridge/freezer 20190819 7088079 - 00 SBNes
Appliance at a glance 1 Appliance at a glance Contents 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 Appliance at a glance............................................ Description of appliance and equipment.................. Appliance range of use............................................. Conformity................................................................ Product data............................................................. External dimensions of the appliance....................... Saving energy........
Appliance at a glance The appliance is only suitable for cooling food 1.5 External dimensions of the appliproducts in a domestic or household-like envi- ance ronment. This includes, for example, use: - in staff kitchens, bed and breakfast establishments, - by guests in country houses, hotels, motels and other accommodation, - for catering and similar services in the wholesale trade. All other types of use are not permitted.
General safety information - Use the holiday function if you intend to be away for an extended period . 1.7 Example of food arrangement Fig. 3 1.8 Smart device The appliance is ready for integration into a smart home and for extended services. Other options can be selected with a SmartDeviceBox. This is activated via the MyLiebherr customer portal. You will find more information about availability and pre-requisites and the individual options on the website www.smartdevice.liebherr.com.
Controls and displays - Do not misuse the plinth, drawers, doors etc. 3 Controls and displays as a step or for support. This applies particularly to children. 3.1 Home screen Danger of food poisoning: - Do not consume food which has been stored too long. Danger of frostbite, numbness and pain: - Avoid lasting skin contact with cold surfaces or refrigerated/frozen food or take protective steps, e.g. wear gloves. Do not consume ice cream, water ice or ice cubes immediately and do not consume them too cold.
Putting into operation 3.3 Navigation Touch the menu to access the individual options. An audible signal sounds after confirming an option or a setting. The display switches to the home screen. The appliance is operated using the following symbols: Standby: Switches the appliance or temperature zone on. Menu: Messages: There are active error messages and reminders. 3.5 Appliance options You can select or set the following options; explanations and setting options, (see 5) : Symbol Calls up options.
Putting into operation 4.2 Installing the appliance q The floor of the installation site must be horizontal and even. q Do not install the appliance in direct sunlight, next to an oven, radiator or similar. WARNING Fire hazard due to dampness! If live parts or the mains lead become damp this may cause short circuits. u The appliance is designed for use in enclosed areas. Do not operate the appliance outdoors or in areas where it is exposed to splash water or damp conditions.
Putting into operation Note u Clean the appliance (see 6.4) . If the appliance is installed in a very damp environment, condensate may form on the outside of the appliance. u Always see to good ventilation at the installation site. 4.
Putting into operation CAUTION Crushing hazard by joint folding up! u Engage safety device. u Engage the locking device in the opening. Fig. 12 u Undo the soft stop mechanism screw with a T15 screwdriver approx. 14 mm. Fig. 12 (1) u Insert a screwdriver behind the soft stop mechanism on the handle side and rotate forwards. Fig. 12 (2) u Remove the soft stop mechanism. Fig. 12 (3) 4.3.2 Remove the bottom soft stop mechanism Fig. 15 u Remove the bearing bracket cover and push it along the hinge. Fig.
Putting into operation Fig. 19 u Carefully remove the grey cable from the guide in the door. Fig. 19 (1) u Press the tab upwards. Fig. 19 (2) u Carefully remove the plug. Fig. 19 (3) u u u u Fig. 17 Undo the screw on the soft stop mechanism about 14 mm with a T15 screwdriver. Fig. 17 (1) Insert the screwdriver on the handle side behind the soft stop mechanism. Turn the unit forwards. Fig. 17 (2) Remove the unit. Fig. 17 (3) Set aside the soft stop mechanism. Fig. 20 u Press the tab. Fig.
Putting into operation 4.3.6 Moving the upper bearing parts to the other side CAUTION Risk of injury if the door tips! u Take good hold of the door. u Set down the door carefully. u Carefully remove the protective cover. Fig. 21 (1) u Undo the bolt a little with a T15 screwdriver. Fig. 21 (2) u Hold the door and remove the bolts with your fingers. Fig. 21 (3) u Lift the door and set it aside. u Carefully lift the plugs out of the door bearing bush with a slotted screwdriver and remove. Fig. 21 (4) 4.3.
Putting into operation u u u w u u Click the cover into place. Fig. 28 (3) Position the screw with a T25 screwdriver. Fig. 28 (4) Position the upper bearing bracket. Fig. 28 (5) Place the pins in the provided screw holes. Tighten the screw. Fig. 28 (4) Insert the screw with a T25 screwdriver and tighten. Fig. 28 (6) 4.3.7 Moving the central bearing parts to the other side Fig. 26 u Insert the cable mirror inverted. w The black mark must be positioned on the edge of the cable holder.
Putting into operation u Undo the screws with a T25 screwdriver and remove the bearing bracket Fig. 30 (3) u Underside of door faces upwards: Turn the door. u Pull out the guide bush: Press the tab with a slotted screwdriver and, at the same time, insert the slotted screwdriver under the guide bush. Fig. 32 (1, 2) u Slide the guide bush included in the scope of supply to the other side of the housing. Fig. 32 (3) u Upper side of door faces upwards: Turn the door. 4.3.
Putting into operation u Carefully lift up the plugs with a slotted screwdriver and remove them. Fig. 35 (1) u Position the door from above onto the lower bearing pins. Fig. 35 (2) u Insert the centre bearing pin through the centre bearing bracket into the lower door. Make sure that the catch mechanism is pointing to the rear. Fig. 35 (3) u Insert the plugs again on the other side of the door. Fig. 35 (4) 4.3.12 Fitting the upper door u w u u w Fig. 34 Position the handle on the other side. Fig.
Putting into operation u Insert the holder with its cable into the opening. Fig. 36 (5) u Press the holder downwards until the tab clicks into place. 4.3.15 Fit the bottom soft stop mechanism Fig. 36 (6) u Insert the plugs. Fig. 36 (7) 4.3.13 Fitting the cable connection Fig. 37 u Engage the plug above the upper bearing bracket and carefully place the cable strands into the channel. Fig. 37 (1) u Carefully position the grey cable in the guide above the top bearing bracket. Fig. 37 (2) Fig.
Putting into operation 4.3.16 Fit the top soft stop mechanism u u w u Fig. 41 Slide the soft stop mechanism on the bearing bracket side at an angle into the slot as far as the limit stop. Fig. 41 (1) Slide the unit in fully. The unit is positioned correctly when the rib on the soft stop mechanism is in the guide in the housing. Tighten the screw with the T15 screwdriver. Fig. 41 (2) Fig. 43 u Position the bearing bracket and engage. If necessary push apart carefully. Fig. 43 (1) u Position the panel.
Putting into operation - The water must be connected to the appliance via a cold water pipe that can withstand the operating pressure and complies with hygiene standards. Use the stainless steel hose supplied (length 1.5 m). Do not reuse old hoses. A 3 m hose is available as an optional extra. This must be professionally installed. A filter with a seal is located in the hose connector.
Putting into operation A [mm] B [mm] C [cm2] D [mm] E [mm] 665 65 Min. 300 Min. 50 Min. 46 x x If wall spacers are used, the dimensions increase by 15 mm (see 4.2) . The dimensions apply for an opening angle of 90 °. Spacing angles will vary according to the opening angle. You can purchase a kit to limit the door opening angle to 90° on soft closing appliances. Please contact our customer service team. The appliance can be built into kitchen units. A top cupboard Fig.
Control w The appliance is switched on. w The appliance is set to the displayed temperatures. This is shown by down arrows. If the screen is black: u Touch the screen. w The standby symbol appears on the whole screen. u Press the standby symbol. w The appliance is switched on. The display switches to the home screen. w The appliance is set to the displayed temperatures. This is shown by down arrows. 4.8.
Control - The internal light is off. 5.4.5 Storage times 5.3.1 Switching SabbathMode on. Guidelines for storage periods at low humidity 0 °C u Press menu. u Press the navigation arrow until SabbathMode is displayed. u Press ON. w SabbathMode is switched on. Only the SabbathMode symbol appears on the screen. SabbathMode switches off automatically after 120 hours if it has not already been switched off manually. The display switches to the home screen.
Control Red currants up to 7 days Cherries, sweet up to 14 days Kiwis up to 80 days Switching off HydroCool u Press menu. u Press the navigation arrows until HydroCool is displayed. u Press OFF. w HydroCool is off. Peaches up to 13 days 5.4.
Control u To remove the humidity control plate: Having removed the drawers, carefully draw the plate forwards and lower it for removal. u Inserting the humidity control plate: Insert the plate from below into the front and back bracket and push back until it clicks into place. 5.4.11 Shelf You can remove and disassemble the shelf above the BioFresh compartments for cleaning. The shelf is prevented from being pulled out accidentally by pull out stops. Each drawer can hold a max. of 25 kg of frozen food.
Control Switching off SuperFrost u Press menu. u Press the navigation arrow until SuperFrost is displayed. u Press OFF. w SuperFrost is switched off. Fig. 56 Setting a higher temperature: u Press plus. Setting a lower temperature: u Press minus. The minus symbol is greyed out when the coldest temperature is selected. The plus symbol is greyed out if it is pressed again after selecting the hottest temperature. The standby symbol is displayed on the screen. u Confirm the required temperature with OK.
Control Using freezer packs u Put the fully frozen freezer packs on the frozen food in the top front section of the freezer compartment. 5.5.10 IceMaker The IceMaker is located in the top drawer of the freezer on the left-hand side. Make certain that the following conditions are met: - The appliance is level. - The appliance is connected. - The freezer compartment is switched on. - The IceMaker is connected to the water supply. Producing ice cubes The production capacity depends on the freezer temperature.
Maintenance u Press OFF. w The ice cube tray moves to the operating position. The IceMaker switches on. w The IceMaker symbol appears in the menu field instead of the IceMaker holiday function symbol. Switching off the IceMaker If no ice cubes are required, the IceMaker can be switched off independently of the freezer compartment. When the IceMaker is switched off, the drawer of the IceMaker can also be used for freezing and storing food. u Cleaning the IceMaker (see 6.5) . u Press Menu.
Malfunctions NOTICE Incorrect cleaning damages the appliance! u Do not use cleaning agents in concentrated form. u Do not use any scouring or abrasive sponges or steel wool. u Do not use any sharp or abrasive cleaning agents, nor any that contain sand, chloride or acid. u Do not use chemical solvents. u Do not damage or remove the type plate on the inside of the appliance. It is important for the customer service. u Do not pull off, bend or damage cables or other components.
Malfunctions error. In this case you will have to be charged for the costs incurred, even during the warranty period. You may be able to rectify the following faults yourself: Appliance does not work. → The appliance is not switched on. u Switch on the appliance. → The power plug is not properly inserted in the wall socket. u Check power plug. → The fuse of the wall socket is not in order. u Check fuse. → The appliance plug does not fit the appliance properly. u Check the appliance plug.
Messages WARNING Danger of injury by LED lamp! The light intensity of the LED lighting corresponds to risk group RG 2. If the cover is defective: u Do not look into the illumination with optical lenses from the immediate proximity. This can cause injury to the eyes. The door seal is defective or needs to be replaced for another reason. → The door seal can be replaced. It can be replaced without the need for special tools. u Contact Customer Service (see 6) : The unit has iced up or condensation has formed.
Decommissioning u Open the water connection. -oru Check the water connection and the hoses (see 4) . -oru Clean the filter. u Switch the IceMaker on (see 5.5.10.2) . u Contact Customer Service if the message persists (see 6) . Other messages FreshAirChange filter (see 6) Clean the ventilation grille (see 6) Open, close IceMaker drawer 9 Decommissioning u Switch off the appliance (see 9) . u Remove mains connector.
Liebherr-Hausgeräte Ochsenhausen GmbH Memminger Straße 77-79 88416 Ochsenhausen Deutschland home.liebherr.
