Installation instructions Refrigerators and freezers for integrated use, door-on-door 090118 7086644 - 00 S/UIK/P 15../ S/UIG/N 15../ S/UIB 15 ...
General safety information Contents 2 Putting into operation 1 General safety information................................... 2 2 2.1 2.2 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 Putting into operation............................................ 2 Transporting the appliance....................................... 2 Installing the appliance............................................. 2 Appliance dimensions.............................................. 3 Recess dimensions..........................................
Putting into operation 2.3 Recess dimensions WARNING Risk of tipping u The appliance must be fixed in accordance with the instructions in order to prevent a hazard caused by the instability of the appliance. This is a base unit and should be installed under a worktop. The kitchen units must be fitted according to the specifications, allowing sufficient ventilation to ensure the equipment works properly.
Putting into operation 2.5 Changing the door direction* NOTICE Risk of damage due to colliding doors! When assembling an appliance with the appliance name beginning with S... next to another appliance: u Install the appliances so that the doors open outwards. Switch the door hinges, if necessary. CAUTION Risk of injury if soft stop contracts! u Carefully remove the soft stop mechanism. u Remove the closing damper: Remove the closing dampers from the ball studs (1), unscrew the bracket (2).
Putting into operation Fig. 6 Fig. 7 CAUTION u Move the hinges. Risk of injury if hinges fold! u Leave hinges open. u Remove the door: Slide the door towards you and out, then lift off the brackets and put aside. Fig. 8 u Move the fixing bracket to the opposite side.
Putting into operation 2.6 Installing the appliance in the recess WARNING Fire hazard from short-circuiting! u When pushing the appliance into the recess, take care not to crush, jam or damage the mains power cable. u Do not operate the appliance with a defective mains power cable. NOTICE Risk of damaging the hinges! If when being pushed the appliance is held by the door, the hinges could be damaged. u When pushing or otherwise moving the appliance, always hold it by the main body.
Putting into operation 2.7.1 Installing the appliance Fig. 15 u If already in place, pull the plinth panel forwards. u Detach the connecting cable from the rear of the appliance, removing the cable holder at the same time because otherwise there will be vibratory noise! u Lay the connecting cable with the help of a string in such a way that the appliance can be easily connected after fitting. Fig. 13 The air flow cavity must be at least 200 cm².
Putting into operation Fig. 20 u Place the foam pad in the plinth panel – this is essential for separating air flows! Fig. 18 u Bend both brackets at one end before installation. Insert the straight edge into the holder on the top of the unit and bend towards the front. u Slide the unit into the recess and level, see Levelling the appliance. Levelling the appliance Fig. 21 u Fit the plinth panel (2) without securing. u Position the unit door and the unit plinth panel for testing.
Putting into operation Fig. 26 Fig. 23 u If affixing the unit under a worktop, use 2 screws to secure the fixing bracket under the worktop. Fig. 24 u If attaching the unit at the side, screw the fixing bracket into the recess with one screw on each side. 2.7.2 Fitting the unit door u Fit the handle on the unit door. Fig. 25 u Check 8 mm presetting. (Distance between appliance door and lower edge of crosspiece) u Push up assembly aids Fig. 25 (12) to unit door height.
Putting into operation The packaging is made of recyclable materials: - corrugated board/cardboard - expanded polystyrene parts - polythene bags and sheets - polypropylene straps - nailed wooden frame with polyethylene panel* u Take the packaging material to an official collecting point. 2.9 Connecting the appliance NOTICE u u u u Fig. 29 Align the cabinet door to the height marked Z: loosen the screws at the top and bottom of the door, then adjust the door.
Putting into operation * Depending on model and options 11
Liebherr-Hausgeräte Ochsenhausen GmbH Memminger Straße 77-79 88416 Ochsenhausen Deutschland home.liebherr.