Installation Guide Under-worktop refrigerators and freezers, door-on-door UR 500 UF 501UB 501 20211126 7086652 - 00
General safety information Contents 1 General safety information........................... 2 2 Transporting the appliance........................... 2 3 Setting up the device..................................... 2 4 Appliance dimensions................................... 4 5 Recess dimensions....................................... 4 6 Cabinet door................................................... 4 7 Reversing the door........................................
Setting up the device WARNING Risk of fire due to moisture! If live parts or the power cord get wet, this can cause a short circuit. u The appliance is designed for use in enclosed spaces. Do not operate the appliance in open space or in damp areas or where there is spray. u Only operate the appliance after it has been installed. WARNING Leaking refrigerant and oil! Fire. The refrigerant contained within the appliance is environmentally friendly, but flammable.
Appliance dimensions 4 Appliance dimensions Fig. 2 Fig. 1 5 Recess dimensions This is an under-worktop appliance and is installed below the worktop. The kitchen cabinet surrounding the appliance must be designed exactly in accordance with the specified dimensions and must allow sufficient air circulation to ensure correct operation of the appliance. The declared energy consumption was determined with a kitchen cabinet depth of 560 mm.
Reversing the door NOTICE An excessively heavy unit door can cause potential damage! If the unit door is too heavy, we cannot rule out damage to the hinges, which may compromise the use of the unit. u Before installing the unit door, ensure the door does not exceed the permissible weight. Appliance type Maximum weight of unit door UR 500 / UF 501 / UB 501 22 lbs (10 kg) 7 Reversing the door WARNING Risk of bodily injury due to the door falling off.
Reversing the door Fig. 6 CAUTION Hinges are spring-loaded and can cause pinching injuries! u Leave hinges open. Fig. 5 u Removing the door: Push the door forward and then out, unhook it and put it to one side. u Remove covers. u Undo the screws on the hinges but do not remove them. u Unscrew the screws only when the door is removed with the hinges.
Reversing the door Fig. 9 u Fitting the door again: Reattach the door to the hinges and tighten the screws. Fig. 7 u Swap the hinges. Fig. 10 u Re-attaching the soft stop mechanism: Screw in the ball studs (1), tighten the retainer (2) and attach the soft stop dampers into the ball studs. Fig. 8 u Swap the fixing bracket to the opposite side.
Installing the appliance in the recess Fig. 11 u Check all screws and retighten if necessary. u Re-fit the covers. 8 Installing the appliance in the recess WARNING Risk of fire due to short circuit! u When inserting the appliance into the recess do not squash, jam or damage the power cable. u Do not operate the appliance with a faulty power cable. NOTICE Risk of damage to the hinges! The hinges could be damaged if the appliance gets caught on the door when it is being moved.
Installation 9.1 Assembling the appliance Fig. 15 Fig. 13 There must be a ventilation gap of at least 200 cm². If there is not enough ventilation, the appliance will consume more energy. u If the appliance plinth trim is already installed, remove it from the front. u Remove the mains cable from the back of the appliance.
Installation Top fastening Fig. 18 u Insert the bracket in the opening in the top of the appliance and turn it forward. u Push the appliance into the recess and align it, see Aligning the appliance. Side fastening: Fig. 19 u Turn both brackets prior to assembly on one end. Insert the straight side in the opening in the top of the appliance and turn it forward. u Push the appliance into the recess and align it, see Aligning the appliance. Aligning the appliance Fig.
Installation u Position the unit door and unit plinth trim for testing u If the plinth trim (2) is visible, pull it forward as far as possible so that the front edge of the ventilation grid and the unit plinth trim lie flush. -oru If the plinth trim (2) is covered, push it fully back.
Installation With a 23-5/8 '' (600 mm) wide recess: u Align the crosspiece Fig. 29 (11) to the middle of the door. Fig. 30 Fig. 27 u For side fastening, fasten the mounting bracket with a screw on the right and on the left in the recess. 9.2 Installing the unit door u Installing the handle on the unit door With a 24-0/2 '' (610 mm) wide recess: u Align the crosspiece Fig. 30 (11) to the middle of the door. u Left strip: Move the crosspiece Fig. 30 (11) 1/4 (6 mm) to the left.
Disposal of packaging Fig. 35 u Position the upper cover and snap it into place. Fig. 32 u Screwing the unit door to the appliance door. u Drill pilot holes in the door of the unit (you could make a preliminary hole with a bradawl) u Screw the appliance door to the unit door with screws through the mounting brackets.
Connecting the appliance WARNING Electrical shock hazard! This appliance is equipped with a three-prong (grounding) polarized plug for your protection against possible shock hazards. Electrical Grounding Required. u Do not remove the round grounding prong from the plug. u Use only an grounded adapter. - Wait 1 hour after installation before you plug in the appliance. This allows the refrigerant and system lubrication to reach equilibrium. - Make sure incoming voltage is the same as the appliance rating.
Connecting the appliance * Depending on model and options 15
For Service in the U.S.: Liebherr Service Center Toll Free: 1-866-LIEBHER or 1-866-543-2437 Service-appliances.us@liebherr.com PlusOne Solutions, Inc. 3501 Quadrangle Blvd, Suite 120 Orlando, FL 32817 For Service in Canada: Liebherr Service Center Toll Free: 1-888-LIEBHER or 1-888-543-2437 www.euro-parts.ca EURO-PARTS CANADA 39822 Belgrave Road Belgrave, Ontario, N0G 1E0 Phone: (519) 357-3320 Fax: (519) 357-1326 www.liebherr-appliances.com Part No.
