FIT 1.0 CM GYM SYSTEM USER GUIDE WARNING: Read and follow all directions for each step to insure proper assembly of this product. CLASS -S PART # 7946001 REV.
TABLE OF CONTENTS Safety Statement.............2 General Notes.................2 Gym Dimensions.............3 Components List.............4 Exploded View...............5 Tool Requirements and Hardware.................6 Assembly Instructions.....7-18 General Maintenance.......19-20 Warranty Statement.........21 Contact Information........22 IMPORTANT SAFETY INFORMATION THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES! 1.
GYM DIMENSIONS 3
COMPONENTS LIST ** ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 QTY . 1 1 1 1 1 1 1 1 1 1 2 1 2 1 1 1 1 1 1 1 2 2 2 2 14 10 4 28 1 4 6 1 7 9 2 2 6 2 2 2 1 2 1 2 1 15 2 1 1 PA RT NO.
EXPLODED VIEW PLACARD PLACEMENT SHROUD KIT SERIAL # SERIAL# (inside of cover) 5
HARDWARE: REQUIRED TOOLS: * 9/16” wrench * Ratchet and 9/16” socket * Adjustable wrench * Tape measure * Two 5/16” Allen wrenches * 4 mm Allen wrench * 3/4 Wrench * Phillups Screw Driver BOLT LENGTH 1/2 0 1/2 1 1/2 2 1/2 3 6 1/2 4 1/2 5 6
SECURLEY TIGHTEN 3/8 x 3/4 3/8 x 1” 3/8 x 3-1/2 FIGURE 1 STEP 1: LOOSELY assemble bottom of the LEFT UPRIGHT (4) and RIGHT UPRIGHT (5) to FRONT UPRIGHT (1) using four 3/8 x 3-1/2 BOLTS (34), eight 3/8 WASHERS (28) and four 3/8 NUTS (33) and TOP PULLEYS (7) LOOSELY assemble the top of the LEFT UPRIGHT (4) and RIGHT UPRIGHT (5) to FRONT UPRIGHT (1) and TOP PULLEYS (7), using four 3/8 x 1” BOLTS (27) for bottom four holes, two 3/8 x 3/4 BOLTS (31) for top two holes and six 3/8 WASHERS (28) as illustr
DO NOT TIGHTEN LOWER FRAME COMPONENTS UNTIL TOP COVERS ARE INSTALLED 6-20 x 1/2 10-32 x 3/8 SECURELY TIGHTEN TOP PULLEY ASSEMBLY (7) AFTER INSTALLING COVER (16) !! DO NOT OVERTIGHTEN SCREWS (25) AND (26) 3/8 x 3-1/2 3/8 x 3/4 FIGURE 2 STEP 2: LOOSELY attach BASE PLATFORM (2) to front of FRONT UPRIGHT (1) using two 3/8 x 3/4” BOLTS (31), and two 3/8 WASHERS (28).
BEFORE PROCEEDING TO STEP THREE, REFER TO SHROUD KIT ASSEMBLY INSTRUCTIONS.
NOTE: REFER TO SHROUD KIT PRIOR TO STARTING STEP 3.
NOTE: SHROUDS HAVE BEEN REMOVED FOR ILLUSTRATIONAL PURPOSES ONLY EYE HOOK ORIENTATION LEA7745402 FIGURE 4 MUST DISASSEMBLE ONE END OF CABLE AND REASSEMBLE AFTER ROUTING (SEE FIG 7 PAGE 14) STEP 4 NOTE: IF THE 50# ADD ON KIT WAS PURCHASED, USE THE CABLE FROM THAT KIT AND REFER TO KIT ASSEMBLY INSTRUCTION FOR HEAD PLATE ASSEMBLY Dimension between bottom of PULLEY BRACKET and top of JAM NUT approximately 1 inch.
LEA7746001 FIGURE 5 STEP 5: Insert ball end of GUIDE CABLE 7746001 (42) through eye hook on FLOATING PULLEY BRACKET (11), insert and hook ball end of cable into slotted bushing located at the bottom of frame.
LEA7745401 FIGURE 6 MUST DISASSEMBLE ONE END OF CABLE AND REASSEMBLY AFTER ROUTING (SEE FIG 7 PAGE 14) STEP 6: Insert ball end of LONG CABLE 7745401 (44) under pulley #1 and thru slot in BASE PLATFORM (2). Run cable underneath and up the back side of pulley #2. Then run cable up and around the front and down the back side of pulley #3. Run cable to back side of pulley #4 around and up the front side to the back side and over the top of pulley #5 and out to the front.
QUICK CONNECT ASSEMBLY - PART NUMBER 7872601 ITEM QTY. PART NO. DESCRIPTION 1 1 7726201 COUPLER, QUICK CONNECT LEA7726201 4 1 7726401 HSNG, QUICK CONNECT LEA7726401 3 1 7726301 SLEEVE, QUICK CONNECT LEA7726301 2 1 3249901 SPRING, COMPRESSION LEA3249901 5 2 3250002 M5 X 0.8 HXS SOC CS ST BZ X 8 LEA3250002 FIGURE 7 STEP 7: USE THIS ASSEMBLY AT THE END OF EACH CABLE Slide each item onto cable as follows: ITEM 1, ITEM 2, ITEM 3, and insert cable end into ITEM 4.
3/8 x 2-1/2 10-32 x 3/8 FIGURE 8 STEP 8 Attach FRONT SHROUD (8) using two 3/8 X 2-1/2 SCREWS (35) and two 3/8 WASHERS (28) Attach REAR BOTTOM PLATE (13) using two 10-32 X 1/2 SCREWS (25) SECURELY TIGTHEN CABLE GUIDES (REFER TO FIG 5, PAGE 11) 15
3/8 x 3/4 PIN MUST BE LOCATED ON TOP SIDE FIGURE 9 STEP 9: Pre-assemble two FLANGE BEARINGS (23) and SHAFT (32) into ADJUSTMENT HUB as illustrated Attach ROLLER PAD ASSEMBLY (3) to center hole ADJUSTMENT HUB using two 3/8 WASHERS (28) and two 3/8 X 3/4 BOLTS (31) and tighten SECURELY.
!! DO NOT OVERTIGHTEN SCREWS 10-32 x 3/8 INSTALL SCREW (25) BEFORE SCREWS (26) 6-20 x 1/2 10-32 x 3/8 6-20 x 1/2 FIGURE 10 STEP 10: Attach TOP COVER (15) using four METAL SCREWS (25) Attach FRONT and BACK MID COVERS (18), (19) to each other using four PLASTIC SCREWS (26) as shown in illustration. Attach BACK MID COVER to FRONT UPRIGHT (1) using two METAL SCREWS (25) Finally align and stick MEDALLION (20) to front of MID COVER (19) as shown. AVOID DAMANING PLASTICS COMPONENTS.
REFER TO SHROUD KIT FIGURE 11 STEP 11: Lift HEAD PLATE ASSEMBLY and insert 15 or 20 W EIGHT PLATES (46). Apply W EIGHT STACK LABELS (47) starting with “1” on the HEAD PLATE and descending down. REFER TO SHROUD ASSEM BLY GUIDE TO ASSEM BLY REAR SHROUD Referencing step 7, push back on ITEM (3) at end of cable and attach SHORTER HANDLES (38) to top of frame Repeat process for attaching the ADJUSTABLE HANDLES (40 ) to the lower cable ends and the medium handles (39) to the middle ends.
MAINTENANCE Please note: * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your Life Fitness customer service representative at (800) 328-9714.(Outside of the U.S. and Canada, +1-847-288-3300) * Inspect equipment daily. Tighten all loose connections are replace worn parts immediately. Failure to do so may result in serious injury * Insure guide rods are lubricated.
CAUTION-PLEASE READ There is a risk assumed by individuals who use this type of equipment. To minimize risk, please follow these rules: 1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately. Failure to do so may result in serious injury. 2. Do not allow minors or children to play on or around this equipment. 3. Exercise with care to avoid injury. 4. Consult your physician before beginning any exercise program.
LIMITED WARRANTY Life Fitness® FIT 1.0 CM Life Fitness extends the following LIMITED WARRANTY to the original owner (proof of purchase required, keep your receipt with this manual) of the Life Fitness product. The Warranty terms apply to IN HOME and LIGHT INSTITUTIONAL USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the Life Fitness product or a weld should crack or break, it will be repaired or replaced by Life Fitness at its option.
LIFE FITNESS 5100 NORTH RIVER ROAD. SCHILLER PARK, IL 60176 U.S.A. Tel: 1.847.288.3300 Fax: 1.800.216.8893 1.800.328.9714 (Toll-free within the U.S. and Canada) www.LifeFitness.com INTERNATIONAL OFFICES Life FitnessAtlantic BV Atlantic Headquarters Bijdorpplein 25-31 2992 LB Barendrecht The Netherlands Phone: (180) 646 666 Fax: (180) 646 703 Life Fitness (UK) Ltd.