S9i Stairclimber A S S E M B L Y I N S T R U C T I O N S
Congratulations... and welcome to the world of Life Fitness and the Life Fitness S9i Stairclimber. The following Parts Identification Listing and the step by step assembly procedures have been assembled to make the set-up of the Stairclimber as quick and easy as possible. Please take special note of the following important points prior to choosing a location and beginning assembly of the Stairclimber.
IMPORTANT SAFETY INSTRUCTIONS! ⇒ DO NOT locate the Stairclimber outdoors, near swimming pools, or in areas of high humidity. ⇒ DO NOT operate your Stairclimber if it has been dropped, damaged, or even partially immersed in water. If this occurs, contact Life Fitness Customer Support Services at the number in the Operation Manual. ⇒ DO NOT locate the Stairclimber any closer than 30 inches ( 76 cm ) to a television set.
TOOLS REQUIRED FOR ASSEMBLY... Phillips Screwdriver, T27 Torx Wrench, Socket Set PARTS DESCRIPTION 1 Hex Head Bolt 3/8 – 16 x 3 0017-00101-1048 Qty: 2 2 Lock Nut 3/8 – 16 0017-00103-0025 Qty: 2 3 Hex Head Bolt 5/16 – 18 x 1 0017-00101-0933 Qty: 2 4 Torx Cap Screw 1/4 – 20 x .625 0017-00101-1715 Qty: 10 5 Phillips Pan Head Screw #8 – 18 x .625 0017-00101-1243 Qty: 8 6 Polar Cover Qty: 1 7 Phillips Pan Head Screw #8 – 18 x .75 0017-00101-1242 Qty: 4 8 Phillips Cap Screw #6 – 32 x .
B C 1. Before proceeding, familiarize yourself with the parts of the Stairclimber and make sure that you have received all the items described in the Parts List. 18 2. 10 Locate the MONOCOLUMN (#10). Position the MONOCOLUMN SHROUD (#18) onto the MONOCOLUMN as shown. Position the MONOCOLUMN near the MONOCOLUMN MOUNTING BRACKET (B) as shown. Detach and feed the CONSOLE WIRE HARNESS (C) through the MONOCOLUMN and out through the DISPLAY CONSOLE MOUNTING BRACKET (D) ACCESS HOLE.
4. Locate the TELEMETRY CABLE (#15). Feed the 3-PIN CONNECTOR (3P) end of the cable through the front of the HANDLEBAR ASSEMBLY (#13). The cable must be routed down the HANDLEBAR BRACKET TUBE (F) and back up the top of the MONOCOLUMN (#10). Feed the 3-PIN CONNECTOR through the DISPLAY CONSOLE MOUNTING BRACKET (D) ACCESS HOLE. D 3P 13 10 F 5. 15 Secure the HANDLEBAR ASSEMBLY (#13) to the HANDLEBAR BRACKET TUBE (F) using six MOUNTING SCREWS (#4). Tighten the SCREWS securely. 4 13 F 6.
. 8. Locate one of the VERTICAL HANDRAILS (#12). Carefully insert the top of the VERTICAL HANDRAIL into the user right end of the HANDLEBAR ASSEMBLY (#13). Align the mounting holes. Secure the VERTICAL HANDRAIL to the HANDLEBAR ASSEMBLY using two MOUNTING SCREWS (#4). Position the bottom of the VERTICAL HANDRAIL over the mounting hole in the top of the right FRAME LEG (K). Using one HEX HEAD BOLT (#3), mount the VERTICAL HANDRAIL to the right FRAME LEG as shown. Tighten the BOLT securely.
14. Position the unit in the desired location for use. Insert the POWER SUPPLY (#17) connector into the POWER JACK located at the base of the shroud near the FRONT STABILIZER (M). Plug the POWER SUPPLY into a wall outlet. 17 PRE-OPERATION CHECKLIST M ü Ensure that all fasteners are tight. ü Make sure the Stairclimber is properly leveled and stable. (Refer to the Operation Manual) ü Ensure that the Leveler Jam Nuts are tight.
M051-00K20-A315 4/02