ADVANCED, ELLIPTICAL TRAINER ITEM NO.: 93390 OWNER’S MANUAL IMPORTANT: Read all instructions carefully before using this product. owner’s manual for future reference. Retain this The specifications of this product may vary from this photo, subject to change without notice. 2010, Aug.
TABLE OF CONTENTS WARRANTY---------------------------------------------------------------------------------1 SAFETY INSTRUCTIONS-------------------------------------------------------------- 2 ADJUSTMENTS--------------------------------------------------------------------------- 3 OPERATING THE COMPUTER------------------------------------------------------- 3 PARTS LIST-------------------------------------------------------------------------------- 6 HARDWARE PACKING LIST------------------------------------
SAFETY INSTRUCTIONS Basic precautions should always be followed, including the following safety instructions when using this equipment: Read all instructions before using this equipment. 1. Read all the instructions in this manual and do warm up exercises before using this equipment. 2. Before exercise, in order to avoid injuring the muscle, warm-up exercise of every position of the body is necessary. Refer to Warm Up and Cool Down Routine page.
ADJUSTMENTS Adjusting the Tension Control Knob To increase the load, turn the tension control knob in a clockwise direction. To decrease the load, turn the tension control knob in a counterclockwise direction. Adjusting the Adjustable Leveler Turn the adjustable leveler on the rear stabilizer as needed to level the elliptical trainer. OPERATING THE COMPUTER SPECIFICATIONS: TIME---------------------------------------------------- 0:00-99:59 MIN: SEC SPEED------------------------------------------------- 0.
TIME: Press MODE button until the screen displays TIME; the computer will display your elapsed workout time in minutes and seconds. When you start to exercise, time starts counting up from 0:00 to 99:59 minutes per 1 second increment. You may also preset target time before training. Press MODE button to select TIME function and then press SET button to preset target time. Press RESET button to clear the target values of TIME to zero. The preset target time range is from 0:00 to 99:00 minutes.
on to the handlebar grip sensors with two hands instead of just with one hand only when you try to test your heart rate figures. You may also preset target heart rate before training. Press MODE button to select PULSE function and then press SET button to preset target heart rate. Press RESET button to clear the target heart rate to zero. The preset heart rate range is from 40 to 240 beats/minute.
PARTS LIST No. Description Qty No. Description Qty 001 Main Frame 80x40x2 1 024 Nylon Nut M6 10 002L Left Foot Bar 40x25x1.5 1 025 Washer Ø6 6 002R Right Foot Bar 40x25x1.5 1 026 Bolt M6x40 6 003L Left Handrail Arm Ø32x1.5 1 027 Tension Cable L=1800 1 003R Right Handrail Arm Ø32x1.5 1 028 Cap S13 2 004L Left Handrail Ø32x1.5 1 029 Screw ST4.2x25 15 004R Right Handrail Ø32x1.5 1 030L Foot Bar Cover-A 2 005 Front Post Ø60x1.5 1 030R Foot Bar Cover-B 2 006 Handlebar Ø25x1.
PARTS LIST No. Description Qty No. Description Qty 050R Right Handrail Arm Cover-B 1 074 Hexagon Nut 7/8” 1 051 Tension Control Knob 1 075 Belt Pulley with Crank 6.5”/Ø260 1 052 Screw ST4.
HARDWARE PACKING LIST (13R) Bolt for right U Shape Bracket 1/2” (14R) Right Nylon Nut 1/2” (15) Wave Washer Ø28xØ17x0.3 (17) Spring Washer Ø20 (13L) Bolt for left U Shape Bracket 1/2” (14L) Left Nylon Nut 1/2” (15) Wave Washer Ø28xØ17x0.3 (17) Spring Washer Ø20 1 PC 1 PC 1 PC 1 PC (9) Bolt M8x70 4 PCS (11) Big Curve Washer Ø20xØ8 4 PCS (24) Nylon Nut M6 10 PCS (25) Washer Ø6 6 PCS (28) Cap S13 2 PCS (45) Curve Washer Ø6 4 PCS (29) Screw ST4.2x25 4 PCS (94) Screw ST4.
TOOLS Allen Wrench 8mm 1 PC Multi Hex Tool 1 PC Allen Wrench 6mm 1 PC Multi Hex Tool with Phillips Screwdriver S8, S13, S14, S15 1 PC 9
10 37 29 40 56 58 94 94 67 35 32 46 41 39 29 9 3L 42 43 2445 49L 93 69 88 55 21 86 13L 60 38 29 22 11 20 16 38 29 83 82 60 1 14L 10L 92 54 94 4R 66 9 40 56 58 39 28 23 20 32 10R 87 63 77 79 13R 69 1615 14R 17 86 22 89 21 30R 60 34 94 46 50R 41 95 80 96 18 25 24 76 30L 2R 26 43 42 44 12 11 47 8 65 60 29 39 81 31 3R 43 24 45 49R 83 82 94 87 63 84 85 84 85 17 12 51 64 65 11 41 5 27 48 57 53 64 88 28 23 86 91 33 151
ASSEMBLY INSTRUCTIONS 7 9 11 12 1 12 11 Tool: 12 11 8 Multi Hex Tool with Phillips Screwdriver S8, S13, S14, S15 9 1. Front and Rear Stabilizers Installation Position the Front Stabilizer (7) in front of Main Frame (1) and align bolt holes. Attach the Front Stabilizer (7) onto the front curve of the Main Frame (1) with two M8x70 Bolts (9), Ø20xØ8 Big Curve Washers (11), and M8 Cap Nuts (12). Tighten bolts with the Multi Hex Tool with Phillips Screwdriver provided.
A B 27 51 51 27 62 61 51 27 5 41 11 11 41 38 Tool: 38 64 65 27 1 Multi Hex Tool with Phillips Screwdriver S8, S13, S14, S15 Allen Wrench 6mm 2. Front Post and Tension Control Knob Installation Remove six M8x15 Bolts (38), Ø8 Spring Washers (41), and Ø20xØ8 Big Curve Washers (11) from the Main Frame (1). Insert the Tension Cable (27) through into the bottom hole of Front Post (5) and pull it out from the square hole of Front Post (5).
40 46 48 41 42 Tool: 5 3R 3L 2R 30R 26 30L 33 Multi Hex Tool 2L 17 75 Multi Hex Tool with Phillips Screwdriver S8, S13, S14, S15 14R 25 24 13L Allen Wrench 8mm 15 13R 60 29 60 28 14L 15 17 23 20 3. Left/Right Handrail Arms, Left/Right Foot Bars, Left/Right Foot Pedals, and Foot Bar Covers-A/B Installation Remove two M8x20 Bolts (40), Ø8 Spring Washers (41), Ø10 Big Washers (46), and Ø38x3 Washers (42) from the left and right horizontal axes of the Front Post (5).
4R 24 4L 45 Tool: 24 44 45 3R 44 3L 5 Multi Hex Tool with Phillips Screwdriver S8, S13, S14, S15 4. Left and Right Handrails Installation Attach the Left/Right Handrails (4L, 4R) onto the Left/Right Handrail Arms (3L, 3R) with four M6x35 Bolts (44), Ø6 Curve Washers (45), and M6 Nylon Nuts (24).
29 49R 90 94 4R 4L 54 Tool: 94 50R 49L 5 3L 3R 94 Multi Hex Tool with Phillips Screwdriver S8, S13, S14, S15 50L 94 5. Front/Rear Decorate Covers and Left/Right Handrail Arm Covers-A/B Installation Attach the Front and Rear Decorate Covers (90, 54) onto the Front Post (5) with two ST4.2x25 Screws (29). Attach the Left Handrail Arm Cover-A (49L) and Left Handrail Arm Cover-B (50L) onto the Left Handrail Arm (3L) with four ST4.2x12 Screws (94).
53 6 Tool: 55 64 38 Multi Hex Tool with Phillips Screwdriver S8, S13, S14, S15 88 93 5 Allen Wrench 6mm 6. Computer and Handlebar Installation Remove four M5x10 Bolts (88) from the back of the Computer (53). Remove two M8x15 Bolts (38) and Ø16xØ8 Curve Washers (93) from the Front Post (5). Insert the Hand Pulse Sensor Wires (55) from the Handlebar (6) into the hole on the Front Post (5) and then pull them out from the top end of the Front Post (5).
MAINTENANCE Cleaning The elliptical trainer can be cleaned with a soft cloth and mild detergent. Do not use abrasives or solvents on plastic parts. Please wipe your perspiration off the elliptical trainer after each use. Be careful not get excessive moisture on the computer display panel as this might cause an electrical hazard or electronics to fail. Please keep the elliptical trainer, specially, the computer console, out of direct sunlight to prevent screen damage.
WARM UP AND COOL DOWN ROUTINE A good exercise program consists of a warm-up, aerobic exercise, and a cool down. Do the entire program at least two to three times a week, resting for a day between workouts. After several months you can increase your workouts to four or five times per week. AEROBIC EXERCISE is any sustained activity that sends oxygen to your muscles via your heart and lungs. Aerobic exercise improves the fitness of your lungs and heart.
SIDE STRETCHES Open your arms to the side and lift them until they are over your head. Reach your right arm as far toward the ceiling as you can for one count. Repeat this action with your left arm. QUADRICEPS STRETCH With one hand against a wall for balance, reach behind you and pull your right foot up. Bring your heel as close to your buttocks as possible. Hold for 15 counts and repeat with left foot. INNER THIGH STRETCH Sit with the soles of your feet together and your knees pointing outward.
TOE TOUCHES Slowly bend forward from your waist, letting your back and shoulders relax as you stretch toward your toes. Reach as far as you can and hold for 15 counts. HAMSTRING STRETCHES Extend your right leg. Rest the sole of your left foot against your right inner thigh. Stretch toward your toe as far as possible. Hold for 15 counts. Relax and then repeat with left leg. CALF/ACHILLES STRETCH Lean against a wall with your left leg in front of the right and your arms forward.
