Introduction This Instruction Manual is universal for portable air conditioners manufactured by lifesmart.The appearance of your unit might be slightly different than the one described in this manual. Operation and usage of your air conditioner should not vary. In order to ensure your safety, Please carefully read the sections that correspond with your unit. Also, keep the manual in a safe place for future reference.
INTRODUCTION PORTABLE AIR CONDITIONER This Portable Air Conditioner is a small size appliance that has multiple functions. Some functions of this unit are that it can adjust the temperature and humidity in a room, cool, dehumidify, and fan. The unit was designed to be used in home and office environments with a compact design compared to others. Other air conditioning patterns are recommended when the ambient temperature 0 0 0 0 is either below 18 C(65 F) or above 35 C(95 F).
PARTS FRONT Control knob Adjustable air fins Cold air outlet Handle BACK Note:Features and appearance may vary depending on your air conditioner model.
CONTROL PANEL CONTROL PANEL 1 Before you insert the plug,please make sure the knob is turned to the "OFF" position. OFF:When the knob is turned to "OFF",the air conditioner will stop operation. LO FAN: When the knob is turned to "LO FAN",the air conditioner will be in low fan operation mode to delivery weak airflow. HI FAN: When the knob is turned to "HI FAN",the air conditioner will be in high fan operation mode to delivery strong airflow.
CONTROL PANEL CONTROL PANEL 2 Note:Features and appearance may vary depending on your air conditioner model. 1 REMOTE CONTROLLER SIGNAL RECEIVER 2 DIGITAL DISPLAYER FAN Mode: Indicates room temperature. COOL or DRY Mode: Indicates setting the temperature. TIMER Operation: When pressing the TIMER button, this indicates timer time. If the time has not been adjusted, after 5 seconds the temperature will appear. ROOM TEMP SENSOR Failure: Display indicates temperature at 77F/25C.
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 1 Set temperature indicator Fan speed indicator Lock/Hold key indicator Present time indicator +/- button Increase or decrease the room tem2 3 perature or set the timer duration 4 after pressing the timer button. On/off button Turn the unit on or stop operation and turn the unit off. 5 6 Hour button Set the hour on the unit clock by 10 12 pressing and holding this button, then pressing the minute button re11 peatedly to the correct time.
REMOTE CONTROL PRESENT TIME SETTING PROCEDURE When cells are inserted,under the timer operation has not been set,do it as following procedure, EX:set to AM:10:30. 1 Continually press the HOUR button about 2 seconds. The time indicator is flickering and can set the HOUR time. 2 Press the HOUR button. (Set to AM 10:) 3 Press the MIN button. (Set to 30) 4 Press the ON/OFF button to confirm the set time or it would automatically exit the time setting state after 15 seconds.
WATER DRAINAGE Water Drainage: The air conditioner evaporates condensed water and discharges the moisture through the hot air outlet. In some cases it is possible that all water did not evaporate and the internal water tank can be full. If this is the case, the WATER FULL light will illuminate and the unit will stop running. Follow the steps to drain the water. *Power off then unplug the air conditioner,disconnect the exhaust hose from the back,and move the unit to a suitable drain location or outdoors.
MAINTENANCE/SERVICE Continuous Drainage In a high humidity environment, if possible the user can have a continuous drainage. This can reduce the number of times you have to pour out water. Condensation is discharged by gravity through a hose (not provided). Of course, this method will reduce the efficiency of the unit. a) Pulll out the partition plate stopper. b) Connecting the hose to partition plate joint and lead it to the floor drain.or a suitable area for draining the condensate.
MAINTENANCE/SERVICE ! WARNING *Pull the plug out of the socket before cleaning. *To prevent accidents caused by electrical shock, make sure there is no power to the unit before beginning maintenance or repair. CLEANING OF AIR FILTER If the air filter is blocked,the air flow volume will reduce.Clean the filter once every two weeks. Open and clean the air filter 1. Directly grasp the hook on the bottom to remove the air filters with the direction of the arrow. 2.
MAINTENANCE/SERVICE AFTER THE OPERATIONAL SEASON 1.Turn off the air conditioner and disconnect the power source. 2.Properly maintain the air filter and other parts. 3.Open the partition plate stopper and the base stopper to drain out the water of the partition plate and the base.Operate the unit in fan mode for half an hour to make sure the partition plate and the base is dry. 4.Please use a plastic sheet to cover the unit to prevent dust or filth from entering the unit.
TROUBLESHOOTING Before calling lifesmart technical support, please check the following. Trouble Air conditioner does not operate at all Cooling efficiency is not good Check *Is there power? *Is it plugged in? *Did the fuse or circuit breaker switch off? *The WATER FULL light is illuminated.
INSTALLATION Installation location Put the portable air conditioner in a flat location where the air outlets cannot be obstructed. Make sure the unit has 3 ft around it for airflow. Installation and Uninstallation of the Air Exhaust Hose See the figure below,First the user must take out the the hose.
INSTALLATION Installation and Uninstallation of the Air Exhaust Hose Installation: See the figure below. Attach the air exhaust adapter into the air exhaust hose (Use the arrows for direction). Then attach the air exhaust hose into the air conditioner. Uninstallation: See the figure below. detach the air exhaust adapter into the air exhaust hose (Use the arrows for direction). Then detach the air exhaust hose into the air conditioner.
INSTALLATION Window Kit Installation Your window kit has been designed to fit most standard "vertical" and "horizontal" window applications.However,it may be necessary for you to improvise/modify some aspects of the installation procedures for certain types of windows. See the figure below, Horizontal window Window slider kit Minimum:27-1/2"(70cm) Maximum:48(122cm) Vertical window Window slider kit Minimum:27-1/2"(70cm) Maximum:48(122cm) Instructions: Use one screw to fix installation board ll in place.
INSTALLATION Air Exhaust Hose Mounting Method The air exhaust hose is 20 cm - 160 cm in length.It is suggested that the hose be as short as possible to achieve maximum efficiency. If you need to extend the hose, please use the previous mounting method instructions: 1.Try to avoid bending the hose. 2.Try to avoid bending the hose near the exhaust air outlet (if you need to bend the hose, the bending point should be at least 50 cm away from the exhaust air intake). 3.
16
