INSTRUCTION FOR USE PH050010/PH050011/PH050012/PH050013 PH050014/PH050015/PH050017/PH050018 INFLATABLE SPA
QUESTIONS?? DO NOT CONTACT YOUR RETAILER, CONTACT OUR SPA EXPERTS AT 800-279-1906 OR EMAIL AT SERVICE@FIRSTSPAUSA.
IMPORTANT SAFETY INSTRUCTIONS WARNING1: WARNING2: WARNING3: WARNING4: WARNING5: WARNING6: WARNING7: WARNING8: WARNING9: WARNING10: WARNING11: WARNING12: WARNING13: WARNING14: WARNING15: WARNING16: WARNING17: WARNING18: WARNING19: CAUTION1: CAUTION2: The Spa should be supplied through a residual current device (GFCI) with a rated tripping current not exceeding 20 AMPS. Electric installations should fulfill the requirements of local standards.
CAUTION3: CAUTION4: CAUTION5: CAUTION 6: CAUTION 7 : CAUTION 8: Place only on surface that can withstand the floor loading requirement of your spa. The spa should not be setup or left out in temperatures lower than 4°C (40°F). Only add chemicals once the spa is filled with water and only as needed.
INSTALLATION INSTRUCTION ENSURE TO CHECK ALL PARTS ARE PRESENT: a. Spa b. PU cover with foil and zipper c. Inflation hose d. Filter cartridge e. Filter cartridge cover f. Rubber plug g. Repair kit SITE REQUIREMENTS: WARNING1: The floor has to be capable of supporting the expected load. WARNING2: An adequate drainage system has to be provided to deal with overflow water.
INDOORS INSTALLATION: Be aware of special requirements if you install the spa indoors. 1. The floor must be able to withstand the capacity of the spa. The floor should be a non-slip, level surface. 2. Proper drainage is essential for indoor spa installation. When building a new room for the spa it is recommended that a floor drain be installed. 3. Humidity is a natural side effect of spa installation. Determine the effects of airborne moisture on exposed wood, paper, etc. in the proposed location.
2. Open the air outlet on the spa. Screw one end of the inflation hose onto it. 3. Open the air valve on the equipment control unit. Connect the other end of inflation hose into the valve. 4. Inflate the spa tub by pressing the Jet “Bubble” button. When the spa is properly inflated, press the “Bubble” button to shut off the bubbles. Attention 1: Do not over inflate.
7. Screw the filter cartridge onto the water inlet on the spa wall by turning it clockwise. 8. Use a garden hose to fill the spa with water to the water level printed on the spa wall. 9. Place the cover onto the spa, fasten the zipper.
OPERATION You must insure the water in the spa matches the water line printed on the spa wall. Never dry-run the power pack as such type of operation will void the warranty. CONTROL PANEL FILTER BUTTON - On-off button for the filtration system. Press this button, and the filter pump will turn on and the button red indicator light will turn on. Press again, the pump will stop working and the light will turn off.
Base of the topside control panel is made of environmental-friendly PU material that is soft and comfortable. Surface of the base can be washed. The topside control panel is chrome-plated, which meets ROHS standards. Surface films are glued to the panel by marine glue. BODY OF SPA: 1. Filling the spa with water: water should be filled to a position 1 inch higher than the water line. If lower, the heating system may not turn on. If higher, water may spill over the spa side while in use. 2.
MAINTAINING Maintaining water 1. Clean your filter cartridge at least once every time you have used a your spa approximately for 72- 120 hours. The filter cartridge should be replaced at least once a month depending on use. 2. Change water every few days or use appropriate spa chemicals. All spas require the use of spa chemicals. Please consult your local spa supply retailer for more information about chemical maintenance. Pay close attention to the chemical manufacturer’s instructions.
4. The filter cartridge can be rinsed off with a garden hose and reused. However, if the filter cartridge remains soiled and discolored the filter cartridge should be replaced. 5. Put on the filter cartridge cover and place the filter cartridge to water inlet by turning it clockwise. Drainage 1. Make sure to unplug the power pack from the electrical receptacle. 2. Put the plastic plug into the outlet in the inner wall of the spa. 3. Open the outlet in the outer wall of the spa.
REPAIR AND STORAGE 1. Spa Repair - If the spa is torn or punctured, use the provided repair patch Dry the area to be repaired. Apply the glue from the accessory bag to the repair patch and then attach it onto the damaged area. Smooth the surface to remove any air bubbles. A secure unnoticeable repair can usually be made. 2. Spa Storage - Make sure all water is drained from the spa and control box. This is essential to extend the life of the spa.
WATER PROTECTION LEVEL Warning: Water protection levels of the spa at different product zones are different. See the below scheme: 59” 99” 59” 79” 59” NOTE: The measured zone dimensions are limited by walls and fixed partitions. Above figure--Zone dimensions of swimming pools and paddling pools. 99” 79” 59” Zone 1 Note: The measured zone dimensions are limited by walls and fixed partitions. Above figure—Zone dimensions of swimming pools and padding pools. SAFETY & ANNOUNCEMENTS 1.
LIMITED WARRANTY - TERMS & CONDITIONS This warranty extends to the original purchaser only. The warranty period commences on the original purchase date through 6-12 months according to the different parts. This warranty is not transferable to subsequent purchasers. This warranty is subject to the obligations, limitations, and exclusions listed below. - Extent of warranty: 6 months warranty on spa body and plumbing, 12 months spa pak and electric parts.
AQUA SPA REGISTRATION Full Name: Email: Phone: Address: City: State: Spa Model: Spa Serial #: Zip Code: PH500013 PH500015 PH500017 PH500018 Can be found on a white sticker on the box plastic. Place of Purchase and City: Date of Purchase: Comments: Mail to: First Spa USA, 171 West 7065 South, Midvale Utah 84047.
