Table of Contents Getting Started 4 5 Welcome Warranty Desk Assembly OWNERS MANUAL Treadmill/Bike Desks: DT-3/DT-5/DT-7 8 13 DT-5 Desk Assembly Instructions Desk Leveling and Height Adjustment 14 19 DT-7 Desk Assembly Instructions Desk Leveling and Height Adjustment 20 21 22 DT-5 Manual Treadmill Desk Assembly DT-7 ElectricTreadmill Desk Assembly DT-3 Console Assembly Treadmill Desk Operations 24 26 28 30 32 Console Overview Innovative Features Troubleshooting Personal Settings Bike Desk Operati
Welcome Congratulations on choosing the LifeSpan Workplace line of products. These products give you the opportunity to remain productive while taking care of yourself as you integrate movement with normally sedentary tasks. The average American now spends eleven hours, five days a week, sitting, and burns one-hundred fewer calories each day than they did a few decades ago. Sitting for long periods slows your metabolism, reduces calories burned, and increases your risk for heart disease and diabetes.
Warranty Exclusions and Limitations: • This warranty does not apply to any defects caused by negligence, misuse, improper assembly or maintenance, accident, or an “act of god”. • This warranty does not apply to discoloration of paint or plastics. • LifeSpan shall not be responsible for incidental or consequential damages. • This warranty is nontransferable from original owner. Registration (U.S. and Canada Only) You must register your LifeSpan product before a warranty claim can be processed.
DT-5 Desk: Assembly Instructions DT-5 Desk: Assembly Instructions 2 At LifeSpan we strive to make our equipment easy to assemble and start using. Parts that can be pre-assembled are always assembled and tested on the product line. Prior to starting the assembly process, take all the parts out of the box, remove plastic bags and lay everything out on the floor to become familiar with the components.
DT-5 Desk: Assembly Instructions DT-5 Desk: Assembly Instructions Step 1: Lift Frame Assembly Step 3: Desktop Assembly A. Position the lift frame (1), left base foot (3) and right base foot (4) as shown in the figure to the right. Note the position of the Workplace logo as well as the right and left base feet. B. Place the lift frame onto the left and right base feet mounting bolts and install the M10 washer (5) and M10 acorn nut (6). C. Tighten the four mounting nuts. A.
DT-5 Desk: Assembly Instructions DT-5 Desk: Desk Leveling and Height Adjustment Step 4: Attach the Wire Cover to the Right Extension Tube A. Simply snap the cover (11) over the right extension tube (B). The bottom of the cover will be resting on top of the stop bumper (D). Desk Leveling The desk needs to be leveled prior to use. The desk comes with two adjustable feet that can be used to level the desk and eliminate rocking.
DT-7 Desk: Assembly Instructions DT-7 Desk: Assembly Instructions At LifeSpan we strive to make our equipment easy to assemble and start using. Parts that can be pre-assembled are always assembled and tested on the product line. 2 C 5 Item Number 10 5 B 1 9 6 11 4 A 3 Since your desk is a heavy piece of equipment, it is recommended that you use two people during assembly and follow these assembly instructions to reduce any problems that may occur.
DT-7 Desk: Assembly Instructions DT-7 Desk: Assembly Instructions Step 1: Lift Frame Assembly A. Position the lift frame (1), left base foot (3) and right base foot (4) as shown in the figure to the right. Note the position of the Workplace logo as well as the right and left base feet. B. Place the lift frame onto the left and right base feet mounting bolts and install the M10 washer (11) and M10 acorn nut (6). C. Tighten the four mounting nuts.
DT-7 Desk: Assembly Instructions DT-7 Desk: Desk Leveling and Height Adjustment Desk Leveling The desk needs to be leveled prior to use. The desk comes with two adjustable feet that can be used to level the desk and eliminate rocking. If the desk is rocking on two of the feet, adjust the two front feet until all four feet are sitting securely on the floor. Step 4: Height Adjustment/Console Harness Connections A.
DT-7 Electric Treadmill Desk: Assembly Instructions DT-5 Manual Treadmill Desk: Assembly Instructions Treadmill to DT-5 Desk Assembly Treadmill to DT-7 Desk Assembly A. Position the pre-assembled treadmill as shown below. B. Lift the rear of the treadmill and roll it forward under the desk until the positioning bumpers (D) located on the treadmill are centered over the treadmill position bumper (A) at the base of the uprights. A. Position the pre-assembled treadmill as shown below. B.
DT-3 Console: Assembly Instructions After assembling the bike or treadmill, roll it to the desired location. Plug the console connector into the connector coming from the front of the treadmill or the bottom of the bike. Be sure to screw the two connectors together with the attached thumb screws.
Treadmill Desk Specifications Console Readouts DT-3 Time, Steps, Calories, Distance, Speed LED Yes DT-5 Time, Steps, Calories, Distance, Speed LED Yes DT-7 Time, Steps, Calories, Distance, Speed LED Yes Height Adjustment DT-3 0.4 - 4.0 mph 0.6 - 6.4 kph 12.5” W x 3” D x 2” H 32 cm W x 7.6 cm D x 5.1 cm H NA User Height Range NA Height Adjustment Method Desktop Material NA NA Desktop Surface Maximum Load on Desktop NA NA Desk Lift Speed Desk Height Memory NA NA DT-5 0.4 - 4.0 mph 0.6 - 6.
Treadmill Desk Console Overview Treadmill Desk Console Overview Starting the Treadmill Desk 1. Turn the On/Off switch located on the front right corner of the treadmill to the on position. 2. Make sure the safety key is installed on the console. DT-3 NOTE: The display will show “----“ if the safety key is not installed. 1 3. The current user weight will be flashing on the display panel. Adjust your weight to obtain accurate calorie calculations. 4. Press the Start button to begin your workout.
Treadmill Desk Innovative Features Intelli-GuardTM – This treadmill desk is equipped with our patented Intelli-Guard feature. This feature senses when you stop walking on the treadmill and for safety purposes, it automatically pauses the treadmill to avoid accidental falls which may result in injury. The IntelliGuard feature is triggered when the treadmill senses you are no longer walking.
Treadmill Desk Troubleshooting The LifeSpan Treadmill Desk is designed and manufactured to be reliable and easy to use. However, if you have a problem, these troubleshooting steps may help you find the cause. Problem Solution Problem Solution Problem Solution Only the weight LED is dimly lit. Pressing the start button will make the screen flash. The treadmill desk is in sleep mode. Press and hold the On/Start button for three seconds to power on the unit. The console is erratic or not lighting up.
Treadmill Desk Personal Settings Treadmill Desk Personal Settings To enter Personal Settings mode, press and hold the Stop/Pause button simultaneously with the button. After three seconds, F001 should show in the display. 1. To change between English and Metric mode, press the button until F014 shows in the display. Press enter and either EN or SI will then appear in the display. To change to EN (miles) press the button. To change to SI (kilometers) press the button.
BIKE DESK OPERATIONS 34 35
Bike Desk Specifications Bike Desk Specifications Console Readouts DT-3 Time, Level, Calories, Distance, Speed LED Yes DT-5 Time, Level, Calories, Distance, Speed LED Yes DT-7 Time, Level, Calories, Distance, Speed LED Yes Height Adjustment DT-3 16 Levels 12.5”W x 3”D x 2”H 32cm W x 7.6cm D x 5.1cm H NA Height Adjustment Method Desktop Material NA NA Desktop Surface Maximum Load on Desktop NA NA Desk Lift Speed Desk Height Memory NA NA DT-5 16 Levels 12.5”W x 3”D x 2”H 32cm W x 7.6cm D x 5.
Bike Desk Console Overview Bike Desk Innovative Features DT-3 Console shown here. DT-5/DT-7 Desks follow the same button layout. Audible Safety Alert – The bike desk has an audible alert to notify the user when the cycle desk is starting as well as when the resistance level is being adjusted. 5 1 2 3 4 Console Buttons 1. Start/On – If the console is in sleep mode, press and hold this button for three seconds to turn the console on. Once the console is turned on, press to start the console functions.
Bike Desk Troubleshooting Bike Desk Troubleshooting This bike desk has been designed and manufactured to be reliable and easy to use. However, if you have a problem, these troubleshooting steps may help you find the cause. Problem Solution The console isn’t connecting to personal computer via Bluetooth. Log into your LifeSpan Fitness Club account. Click on the Frequently Asked Questions link located at the bottom of the homepage. If further assistance is needed, please email coordinator@LifeSpanFitness.
Bike Desk Personal Settings To enter Personal Settings mode, press and hold the Stop/Pause button simultaneously with the button. After three seconds, F001 should show in the display. 1. To change between English and Metric mode, press the button until F009 shows in the display. Press enter and either EN or SI will appear in the display. To change to EN (miles) press the button. To change to SI (kilometers) press the button. Disconnect and reconnect the power to the bike. 2.