Treadmill/Bike Desk Owner’s Manual DT5, DT7
Table of Contents Welcome Getting Started Welcome Warranty 5 DT5 Desk Assembly Assembly Instructions Desk Leveling and Height Adjustment 8 DT7 Desk Assembly Assembly Instructions Desk Leveling and Height Adjustment 16 DT5 Manual Treadmill Desk Assembly DT7 Electric Treadmill Desk Assembly 25 26 Treadmill Desk Operations Specifications Setting the Clock Starting the Treadmill Desk Console Overview Preset Button & Bluetooth Innovative Features Troubleshooting Personal Settings Display Details 27 Bik
Welcome Congratulations on choosing the LifeSpan Workplace™ line of products. These products give you the opportunity to remain productive while taking care of yourself as you integrate movement with normally sedentary tasks. The average American now spends eleven hours, five days a week, sitting, and burns one-hundred fewer calories each day than they did a few decades ago. Sitting for long periods slows your metabolism, reduces calories burned, and increases your risk for heart disease and diabetes.
Warranty Your LifeSpan treadmill/bike desk comes with the following limited warranty valid in North America and the United Kingdom. If you are outside of these areas contact your local distributor for warranty information or visit www.LifeSpanFitness.com. Warranty Frame Parts Labor DT5 DT7 Lifetime 2 Years 1 Year Lifetime 2 Years 1 Year LifeSpan warrants the equipment it manufactures is free from defects in materials and workmanship under normal use and services.
DT5 Desk: Assembly Instructions 2 Boxed Separately 16 16 17 14 16a 15 13 15 15 10 11 C B 5 9 7 1 8 6 12 4 A 3 8
DT5 Desk: Assembly Instructions At LifeSpan we strive to make our equipment easy to assemble and start using. Parts that can be pre-assembled are always assembled and tested on the product line. Prior to starting the assembly process, take all the parts out of the box, remove plastic bags and lay everything out on the floor to become familiar with the components.
17 14 16a DT5 Desk: Assembly Instructions 15 13 15 Step 1: Lift Frame Assembly A. Position the Lift Frame (1), Left Base Foot (3) and Right Base Foot (4) as shown in the figure to the right. NOTE: The position of the Desk Position Bumpers (A) face inward, and the long side of the Right and Left Base Feet (3, 4) are opposite of the Height Adjustment Knobs (7) 15 10 C 11 5 9 7 7 Desk Position Bumpers face inward 1 8 Short Side 6 B A 12 4 B. C.
DT5 Desk: Assembly Instructions Step 3: Attach U-Frame to Underside of Desk "RRR" Stickers 13 2 Cable Hole M6x40L Screw "RRR" Stickers 4mm Allen Wrench A. Lay the Desktop (2) face down on a smooth clean surface to attach the U-Frame (13). B. Position the U-Frame (13) as shown to the underside of the Desktop (2). Be sure the open part of the frame faces toward the Cable Hole. The stickers labeled "RRR" on the Desktop and U-Frame should be matched together when assembled. C.
DT5 Desk: Assembly Instructions Step 4: Desktop Assembly A. Make sure the Extension Tube (B) is at level 15 (done in step 2C). B. Align the Desktop on top of the Extension Tubes (B) so the wire harness from the Desktop U-Frame is on the same side as the wire harness coming from the right extension tube. Gently lower the desktop support frame onto the Desktop Mounting Bracket (C).
DT5 Desk: Assembly Instructions Step 5: Console Assembly A. Using the 5mm Allen Wrench with Screwdriver (20) take out the two preinstalled screws from the back and two screws from the bottom of each console end cap so you can remove the end caps. Notice the difference in the screws from the back and bottom as you will be replacing them back into their proper place. B. Align the screw holes in the Console Bracket (14) with the pre-drilled holes in the Desktop (2). C.
DT5 Desk: Assembly Instructions Step 6: Connecting the Wires A. Underneath the front of the Desktop(2) connect the two 7-pin wire harnesses together for console operation. B. Attach the Console Wire Harness Cover (17) to the underside of the Desktop(2) using two #8x1/2L Screws (16a). Push all the extra cable back into U-Frame to help fit cover in place.
DT5 Desk: Desk Leveling and Height Adjustment Desk Leveling The desk needs to be leveled prior to use. The desk comes with two Adjustable Feet that can be used to level the desk and eliminate rocking. If the desk is rocking on two of the feet, adjust the two front feet until all four feet are sitting securely on the floor. Desk Adjustment Feet Desk Height Adjustment A. Loosen the Adjustment Knobs (A) on each upright by turning it no more than two turns counterclockwise. B.
DT7 Desk: Assembly Instructions Boxed Separately 2 16 16 14 17 16a 15 13 15 15 8 C 7 5 10 5 B 1 12 9 6 11 4 A 3 16
DT7 Desk: Assembly Instructions At LifeSpan we strive to make our equipment easy to assemble and start using. Parts that can be pre-assembled are always assembled and tested on the product line. Prior to starting the assembly process, take all the parts out of the box, remove plastic bags and lay everything out on the floor to become familiar with the components.
14 17 16a DT7 Desk: Assembly Instructions 15 13 Step 1: Lift Frame Assembly Access Panel A. Position the Lift Frame (1), Left Base Foot (3) and Right Base Foot (4) as shown in the figure to the right. NOTE: The position of the Desk Position Bumpers (A) face inward, and the long side of the Right and Left Base Feet (3, 4) are opposite of the Access Panel B. Place the lift frame onto the left and right base feet mounting bolts and install the M10 washers (11) and M10 acorn nuts (6). C.
DT7 Desk: Assembly Instructions Step 3: Attach U-Frame to Underside of Desk "RRR" Stickers 13 2 Cable Hole M6x40L Screw 4mm Allen Wrench A. Lay the Desktop (2) face down on a smooth clean surface to attach the U-Frame (13). B. Position the U-Frame (13) as shown to the underside of the Desktop (2). Be sure the open part of the frame faces toward the Cable Hole. The stickers labeled "RRR" on the Desktop and U-Frame should be matched together when assembled. C.
DT7 Desk: Assembly Instructions Step 4: Desktop Assembly NOTE: It is a good idea to use two people for this portion of the assembly in order to be sure wires are properly routed and do not get pinched while installing the desktop. 2 Console Wire Harness Console Wires C Desk Height Control Wire Harness 7 8 5 1 A. Remove the Bolts (7), Washers (5), and Nuts (8) pre-installed in the upright assembly posts. B.
DT7 Desk: Assembly Instructions Step 5: Console Assembly A. Using the 5mm Allen Wrench with Screwdriver (20) take out the two preinstalled screws from the back and two screws from the bottom of each console end cap so you can remove the end caps. Notice the difference in the screws from the back and bottom as you will be replacing them back into their proper place. B. Align the screw holes in the Console Bracket (14) with the pre-drilled holes in the Desktop (2). C.
DT7 Desk: Assembly Instructions Step 6: Connecting the Wires A. Underneath the front of the Desktop(2) connect the two 7-pin and the two 5-pin wire harnesses together for console and height adjustment operation. B. Attach the Console Wire Harness Cover (17) to the underside of the Desktop(2) using two #8x1/2L Screws (16a). Push all the extra cable back into U-Frame to help fit cover in place.
DT7 Desk: Desk Leveling and Height Adjustment Step 7: Height Adjustment/Console Harness Connections A. Remove the two Upper Screws (21) attaching the Access Panel for the Height Adjustment Control Unit. B. Tilt down and pull the Access Panel out several inches. There are harnesses preinstalled to the Height Controller, so do not try to fully remove. C. Attach the Round Connector (23) (placed in the center tray during desktop assembly) to the Height Controller Port (24). D.
DT7 Desk: Desk Leveling and Height Adjustment Desk Leveling The desk needs to be leveled prior to use. The desk comes with two Adjustable Feet that can be used to level the desk and eliminate rocking. If the desk is rocking on two of the feet, adjust the two front feet until all four feet are sitting securely on the floor. Desk Adjustment Feet Desk Height Adjustment A. To raise the desk, press the up or down arrow until the desk is at the desired height. B. C.
Treadmill To Desk: Assembly Instructions Treadmill to DT5 Desk Assembly A. Position the pre-assembled treadmill as shown below. B. Lift the rear of the treadmill and roll it forward under the desk until the Positioning Bumpers (D) located on the treadmill are centered over the Treadmill Position Bumper (A) at the base of the uprights. D Roll Forward A Lift C. D Plug the Console Connector from the desk into the Treadmill Console Port and tighten the thumb screws on the connector. D.
DT7 Electric Treadmill Desk: Assembly Instructions Treadmill to DT7 Desk Assembly A. Position the pre-assembled treadmill as shown below. B. Lift the rear of the treadmill and roll it forward under the desk until the Treadmill Positioning Bumper (D) located on the treadmill are centered over the Desktop Positioning Bumper (A) at the base of the uprights. D Roll Forward A Lift C. D Plug the Console Electronics Cable into the desk D-Connector and treadmill Console Port and tighten the thumb screws.
Treadmill Desk Operations 27
Treadmill Desk Specifications DT5 COMPARE CONSOLES DT7 Time, Steps, Calories, Distance, Speed Time, Steps, Calories, Distance, Speed White LED White LED Bluetooth Yes Yes Buttons Power, Start, Stop, Pre-Set Speed, Up/Down, Change Display Power, Start, Stop, Pre-Set Speed, Up/Down, Change Display Readouts Display MECHANICS & PERFORMANCE Speed Range Dimensions DT5 0.4 - 4.0 mph* 0.6 - 6.4 kph Two Optional Sizes: DT7 0.4 - 4.0 mph* 0.6 - 6.4 kph 47.5” w x 29” d – (120.65 cm w x 73.
Treadmill Desk Setting The Clock To accurately track your activity with apps or other computer systems, the console’s clock must be set. Follow these steps: Press and hold Speed Up and Speed Down for one second. Display shows: TH Press Change Display to move to month setting; after three seconds, display changes automatically.
Starting the Treadmill Desk 1. Turn the On/Off toggle switch located on the front right corner of the treadmill to the on position. If this is already On, press the On/Off button to turn on the console. 2. Make sure the Safety Key is engaged in the console. NOTE: The display will show "–––" if the Safety Key is not engaged. Please make sure that the Safety Key is fully engaged. It is possible the display will not show "–––" when just partially engaged. 3.
Treadmill Desk Console Overview Desk Height Preset 1 Bluetooth 2 Change Display Bluetooth Speed Power Start Stop Preset Reset Desk Height Preset 1 2 Power DT7 only S Bluetooth Change Display Bluetooth Speed Power Start Stop Preset Reset DT7 and DT5 Console Buttons 1. On/Off: Turns on the console. When pressed again, turns off the console; the console must be in standby mode (displaying the current time) for the power off function to work. 2. Start: Starts the treadmill belt.
Treadmill Desk Console Overview Preset (speed) Button Out of the box, the Preset button activates 1.5 mph with a treadmill. Change the speed or resistance in Personal Settings. This feature may be disabled in Settings, setting Preset to OFF. Default is ON. Bluetooth Operation To sync your activity data with your LifeSpan app, press the Bluetooth button, go to the Sync screen on the app, and hold your phone a couple of inches from the console. Syncing will take only a few seconds.
Treadmill Desk Innovative Features Personal Settings – there are several features that can be set using our Personal Settings feature to tailor LifeSpan treadmill desks to your specific preferences. These include: • Maximum Speed: Select 2MPH (3.2KPH) or 4MPH (6.4 KPH) maximum speed options. • Intelli-Guard Selection: On / Off setting • Resume Speed: after pressing pause and returning to the treadmill desk the default belt speed will be .4 MPH (.6 KPH) which is the normal starting speed.
Treadmill Desk Troubleshooting The LifeSpan Treadmill Desk is designed and manufactured to be reliable and easy to use. However, if you have a problem, these troubleshooting steps may help you find the cause. Problem: The console is erratic or not lighting up. Solution: Check to make sure the treadmill desk is properly plugged in. Turn the power switch off and back on again and make sure the Safety Key is in place.
Treadmill Desk Troubleshooting Problem: “dc-6” appears in the display. Solution: Turn the treadmill desk power switch off. Unplug and re-plug the connections made in Step C on page 25 (DT5) on page 26 (DT7). Make sure the thumb screws are properly tightened. Turn the treadmill desk power back on and check to see if it functions properly. Problem: The console isn’t connecting to the app via Bluetooth. Solution: Go to lifespanfitness.com/support, and click to the Apps section of FAQs.
Treadmill Desk Personal Settings Press and hold Change Display for one second to enter Settings mode. Press the up or down arrows to move through the various settings. Press Start to choose a setting to change. Press the up or down arrows to move through the various choices for that setting. Press Start to select a choice. This takes you back to settings mode, where you can move through the other settings. Press Stop to exit Settings mode. Intelliguard — Intelliguard ON/OFF.
Display Details Setting Displayed Choice 1 (Default) Choice 2 Enter Settings mode: SETTG n/a n/a Intelliguard GUARD ON OFF Speed Reset: RESET OFF ON Beep: BEEP ON OFF Speed Limit: L 2 4 Pre Set: SET ON OFF Preset Speed SPEED 1.5 +/- 0.
Bike Desk Operations 39
Bike Desk Specifications DT5 COMPARE CONSOLES DT7 Time, Revolutions, Calories, Distance, Speed Time, Revolutions, Calories, Distance, Speed Display LED LED Bluetooth Yes Yes Readouts MECHANICS & PERFORMANCE Resistance Level Dimensions DT5 16 Levels Two Optional Sizes: DT7 16 Levels 47.5” w x 29” d – (120.65 cm w x 73.66 cm d) 38” w x 29” d – (96.52” cm w x 73.66 cm d) 41” to 55” 104 cm to 140 cm 40” to 53” 101.6 cm to 134.6 cm Manual Electric Desktop Material 1” (2.
Bike Desk Setting The Clock To accurately track your activity with apps or other computer systems, the console’s clock must be set. Follow these steps: Press and hold Speed Up and Speed Down for one second. Display shows: TH Press Change Display to move to month setting; after three seconds, display changes automatically. Use Speed Up or Speed Down arrows to change month Press Change Display Display shows: D Press Change Display to move to day setting; after three seconds, display changes automatically.
Bike Desk Innovative Features Starting the Bike Desk 1. Press the On/Off button to turn on the console. 2. Press the Start, and start pedaling. The console will start counting up from 0:00. 3. Press the Up/Down buttons to adjust resistance.
Bike Desk Console Overview Desk Height Preset 1 Bluetooth 2 Change Display Bluetooth Speed Power Start Stop Preset Reset Desk Height Preset 1 2 Power DT7 only S Bluetooth Change Display Bluetooth Speed Power Start Stop Preset Reset DT7 and DT5 Console Power Buttons 1. On/Off: Turns on the console. When pressed again, turns off the console; the console must be in standby mode (displaying the current time) for the power off function to work. 2. Start: Starts the bike.
Bike Desk Console Overview Bluetooth Operation The Bluetooth communications system in this Workplace Solutions console can send activity information to LifeSpan apps. Your phone must be equipped with Bluetooth 4.0 or later, also known as Bluetooth Low Energy. All iPhones and most Android phones have this. To sync your activity data with your LifeSpan app, press the Bluetooth button, go to the Sync screen on the app, and hold your phone a couple of inches from the console.
Bike Desk Troubleshooting This bike desk has been designed and manufactured to be reliable and easy to use. However, if you have a problem, these troubleshooting steps may help you find the cause. Problem: The console is erratic or not lighting up. Solution: Check to make sure the bike is properly plugged in. Make sure the connectors on the bike and under the desktop are fully plugged in. If the problem persists contact LifeSpan customer service. Problem: “UART” appears in the display.
Bike Desk Personal Settings Press and hold Change Display for one second to enter Settings mode. Press the up or down arrows to move through the various settings. Press Start to choose a setting to change. Press the up or down arrows to move through the various choices for that setting. Press Start to select a choice. This takes you back to settings mode, where you can move through the other settings. Press Stop to exit Settings mode.
Display Details Setting Displayed Choice 1 (Default) Choice 2 Enter Settings mode: SETTG n/a n/a Beep: BEEP ON OFF User Weight: T 150/70 +/-1 Units of measure: UNITS ENGL (M)TRIC Multi-User: USER NO YES Bluetooth-Auto: BT-A OFF ON Sleep SLEEP NO 10/20 Setting 47
DT5/DT7 Treadmill/Bike Desk LifeSpan Fitness P.O. Box 981316 Park City, Utah 84098-1316 Phone: 877.654.3837 www.LifeSpanFitness.com Version 6.