MODEL N° 1529 CO PY OWNER’S MANUAL Keep this Product ID Number and use when contacting Customer Service: 1
REGISTER YOUR PRODUCT ONLINE AT WWW.LIFETIME.COM At Lifetime, we are committed to providing innovative and quality products. While registering, you will have the opportunity to give us your feedback. Your input is valuable to us.
SAFETY INSTRUCTIONS '"*-63& 50 '0--08 5)&4& 8"3/*/(4 .": 3&46-5 */ 4&3*064 */+63: 03 1301&35: %"."(& "/% 8*-- 70*% 8"33"/5: 5P FOTVSF TBGFUZ EP OPU BUUFNQU UP BTTFNCMF UIJT QSPEVDU XJUIPVU SFBEJOH BOE GPMMPXJOH BMM JOTUSVDUJPOT DBSFGVMMZ $IFDL UIF FOUJSF CPY BOE JOTJEF BMM QBDLJOH materials for parts and/or additional instruction material.
TOOLS AND PARTS REQUIRED FOR THIS ASSEMBLY 1/2” Wrench 7/16” Wrench (2) (2) (2) Pliers 3/16” Allen Wrench (1) (2, included) w 8SFODI (2) Phillips Screwdriver Rubber Mallet (1) (1) 'VOOFM Sand 9/16” Wrench Scrap Wood (1) Water Hose (362 lb) (1) (1) *Two adults required to complete assembly* Only adults should set up the product. Do not allow children in the setup area until assembly is complete.
ASSEMBLY GUIDES Refer to the following areas throughout the instructions to assist in the assembly process: This area is located at the top, left-hand corner of the page and indicates which tools and hardware are needed to complete the assembly steps on a page. TOOLS AND HARDWARE REQUIRED FOR THIS PAGE This area is usually located in the bottom, left-hand corner of a step and indicates that special attention is needed to perform a particular part of a step.
PARTS LIST ID ALH ALF ALE AJK AJJ AJI ALX AKZ "+: AKC AKB ALB AKQ AMN AKL AKN ALL AJM ALI AMU AJC AJE AEF AKP AMT AOX AOW "2( Item Description Top Pole Middle Pole Bottom Pole 3JHIU #BDLCPBSE #SBDLFU -FGU #BDLCPBSE #SBDLFU #BDLCPBSE Rim Net Counterbalance Spring 4IPSU &YUFOTJPO "SN -POH &YUFOTJPO "SN Outer Tube Inner Channel Trigger Left Handle Right Handle 1PMF #SBDLFU Base Pole Brace Wheel w Y w "YMF w Y w "YMF Base Plug )FJHIU 4UJDLFS OPU TIPXO 8BSOJOH 4UJDLFS "QQMJFE UP .
HARDWARE LIST ID Item Description BCS Backboard to Rim Assembly Hardware Qty ""4 "#4 "%2 ""# ""+ ABD ABF "#* "#, AJW "06 AAV w Y w )FY #PMU w Y w (BMWBOJ[FE 4QBDFS w Y w 4DSFX w $FOUFSMPDL /VU w )FY 5 /VU 5/16” Washer 7/16” Rubber Washer w Y w 5BQ #PMU w /ZMPDL 'MBOHF /VU Compression Spring w 6 #PMU 5/16” Jam Nut BCR Backboard to Pole Assembly Hardware "%( ""9 "#- "#1 w Y w )FY #PMU w $FOUFSMPDL /VU w Y w #MBD
PARTS IDENTIFIER Parts shown at 10% of Actual Size ALH Y v Top Pole v "-' Y *Warning Sticker applied to side not shown Middle Pole v ALE Y Bottom Pole v ALB Y Outer Tube v AKQ Y 7” Inner Channel AJE Y w Y w "YMF ALI Y Pole Brace 15 3/4” AJC Y w Y w "YMF AJK Y 3JHIU #BDLCPBSE #SBDLFU 17” AKC Y AJJ Y 4IPSU &YUFOTJPO "SN -FGU #BDLCPBSE #SBDLFU AKB Y v -POH &YUFOTJPO "SN 8
PARTS IDENTIFIER Parts shown at 10% of Actual Size ALX Y Rim AKZ Y Net Parts shown at 5% of Actual Size AJM Y Base AJI Y #BDLCPBSE Part shown at Actual Size "&' Y "2( Y Base Plug -PDL 5BC 9
PARTS IDENTIFIER Parts shown at 25% of Actual Size AKL Y Left Handle AKN Y Right Handle AMU Y Wheel AJY Y Counterbalance Spring ALL Y 1PMF #SBDLFU AOW Y AOX Y Spring Retainer Plate Rim Support Channel 10 AMN Y Trigger
HARDWARE IDENTIFIER POLE ASSEMBLY HARDWARE Hardware shown at Actual Size ABH Y ""' Y w Y w )FY #PMU 3/8” Washer ADA Y w Y w 4QBDFS ABB Y w $FOUFSMPDL /VU CIH Y ADS Y Domed CounterTJOL 8BTIFS w Y w 4DSFX POLE TO BASE ASSEMBLY HARDWARE Hardware shown at Actual Size ABD Y AAE Y w Y w )FY #PMU ABN Y 5/16” Washer BTS Y w Y w 4QBDFS w #BSSFM /VU BZO Y AAO Y w Y w 4IPVMEFS #PMU w /ZMPDL /VU BACKBOARD TO RIM ASSEMBLY HARDWARE
HARDWARE IDENTIFIER BACKBOARD TO RIM ASSEMBLY HARDWARE (CONTINUED) Hardware shown at Actual Size ABI Y AAB Y w Y w 5BQ #PMU w $FOUFSMPDL /VU AAJ Y ABD Y "#' Y w )FY 5 /VU 5/16” Washer 7/16” Rubber Washer ABK Y w /ZMPDL 'MBOHF /VU Hardware shown at 25% of Actual Size AOU Y w 6 #PMU AJW Y Compression Spring BACKBOARD TO POLE ASSEMBLY HARDWARE Hardware shown at Actual Size ABP Y ABL Y w Y w $MFBS Poly Spacer w Y w #MBDL Spacer 6 5/8
HARDWARE IDENTIFIER HANDLE ASSEMBLY HARDWARE Hardware shown at Actual Size ADJ Y AAL Y w Y w )FY #PMU AAM Y w Y w 5BQ #PMU w $BQ /VU AAN Y 5/16” Cap Nut ACZ Y w Y w 4QBDFS 6 1/2” (Not actual length) ABB Y ABA Y w $FOUFSMPDL /VU w Y w )FY #PMU 6 5/8” (Not actual length) "%( Y AAX Y w Y w )FY #PMU AQH Y Trigger Spring w $FOUFSMPDL /VU ADR Y ADT Y Y w 1IJMMJQT 1BO )FBE 4DSFX Y w 4DSFX 13
SEC 1 POLE ASSEMBLY HARDWARE REQUIRED Hardware shown at Actual Size ABH Y ""' Y w Y w )FY #PMU 3/8” Washer ADA Y w Y w 4QBDFS ADS Y ABB Y CIH Y w $FOUFSMPDL Nut %PNFE $PVOUFSTJOL 8BTIFS w Y w 4DSFX PARTS REQUIRED Part shown at 25% of Actual Size Parts shown at 10% of Actual Size ALH Y v ALL Y 1PMF #SBDLFU Top Pole "-' Y v *Warning Sticker applied to side not shown Middle Pole ALE Y v Bottom Pole TOOLS REQUIRED Phillips
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE ADS Y CIH Y SEC 1.1 Align the hole in the Top Pole (ALH) XJUI UIF TMPU JO UIF .JEEMF 1PMF "-' and slide the Top Pole over the Middle Pole. Insert a w Y w 4DSFX "%4 through a Domed Countersink Washer (CIH) and into the small hole in the Top 1PMF BOE JOUP UIF TMPU JO UIF .
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE ADS Y CIH Y SEC 1.2 Align the hole in the .JEEMF 1PMF "-' XJUI UIF TMPU JO UIF Bottom Pole (ALE) and slide the Middle Pole over the Bottom Pole. Insert a w Y w 4DSFX (ADS) through a Domed Countersink Washer (CIH) and into the small hole in the .
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE ADA Y 9/16” Y ABB Y ABH Y ""' Y SEC 1.3 Insert the 3/8” x 3 1/2” Hex Bolts (ABH) XJUI UIF w 'MBU 8BTIFST ""' into the .JEEMF 1PMF "-' BT TIPXO 5IFO TMJEF UIF 1/2” x 2.91” Spacers (ADA) POUP UIF )FY #PMUT 1MBDF UIF Pole Bracket (ALL) POUP UIF w Y w )FY #PMUT BOE BUUBDI JU UP UIF .
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Scrap Wood /0 )"3%8"3& 3&26*3&% '03 5)*4 1"(& SEC ATTENTION: THIS STEP CANNOT BE REVERSED! *O PSEFS UP TFBU UIF 1PMFT TUSJLF FBDI FOE PG UIF 1PMF WFSZ IBSE m WF UP TJY UJNFT PO B QJFDF PG TDSBQ XPPE PS DBSECPBSE 5IJT NVTU CF EPOF FWFO JG the Poles cover the slots before seating has occurred. If the 5PQ BOE .JEEMF 1PMFT "-) "-' do not completely cover the slots on the .JEEMF BOE #PUUPN 1PMFT "-' "-& after seating, DO NOT COMPLETE ASSEMBLY.
SEC 2 Bag BCQ POLE TO BASE ASSEMBLY HARDWARE REQUIRED Hardware shown at Actual Size AAE Y w Y w )FY #PMU BTS Y ABD Y w #BSSFM /VU 5/16” Washer ABN Y w Y w 4QBDFS AAO Y BZO Y w /ZMPDL /VU w Y w 4IPVMEFS #PMU PARTS REQUIRED Part shown at 25% of Actual Size Part shown at 5% of Actual Size AMU Y Wheel AJM Y Base Parts shown at 10% of Actual Size ALI Y Pole Brace AJC Y 15 3/4” w Y w "YMF TOOLS REQUIRED 1/2" Wrench Y CCL-3/16” Allen Wr
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE /0 500-4 3&26*3&% '03 5)*4 1"(& AAE Y AAO Y ABD Y ABN Y SEC Attach the flattened end of the Pole Brace (ALI) to the Base (AJM) XJUI UIF IBSEXBSF TIPXO Only finger tighten the hardware for now. 2.1 ALI Curved End AAE Straight End ABD ABD AAO ! AJM Note: Repeat this step to install the other Pole Brace to the other side of the Base.
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 3/16" Y BZO Y 1/2" Y BTS Y SEC 2.3 1MBDF UIF 1PMF BTTFNCMZ PO UIF HSPVOE XJUI UIF 8BSOJOH 4UJDLFS PO UIF .
SEC 3 BACKBOARD TO RIM ASSEMBLY HARDWARE REQUIRED Bag BCS Hardware shown at Actual Size ADQ Y AAS Y w Y w 4DSFX w Y w )FY #PMU ABI Y AAB Y w Y w 5BQ #PMU w $FOUFSMPDL /VU AAV Y 5/16”Jam Nut ABS Y w Y w (BMWBOJ[FE 4QBDFS ABK Y w /ZMPDL 'MBOHF /VU "#' Y ABD Y 7/16” Rubber Washer 5/16” Washer AAJ Y w )FY 5 /VU Hardware shown at 25% of Actual Size AOU Y AJW Y w 6 #PMU Compression Spring 22
SEC 3 BACKBOARD TO RIM ASSEMBLY PARTS REQUIRED Parts shown at 10% of Actual Size ALX Y Rim AJJ Y -FGU #BDLCPBSE #SBDLFU AJK Y 3JHIU #BDLCPBSE #SBDLFU Part shown at 5% of Actual Size AJI Y #BDLCPBSE Part shown at 25% of Actual Size AOX Y AOW Y Rim Support Channel Spring Retainer Plate TOOLS REQUIRED Pliers 1/2” Wrench 7/16” Wrench Y 23 3/8” Wrench
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 7/16” Y AAS Y AOU Y (Not to scale) SEC AAB Y ABS Y Slide the w 6 #PMU "06 through the Left and Right Backboard Brackets (AJJ & AJK) 5IF 6 #PMU NVTU SFTU JO UIF OPUDIFT PG UIF #BDLCPBSE #SBDLFUT BT TIPXO 3.1 AJK AJK AJJ AJJ AOU SEC 3.2 Notch AOU $POOFDU UIF #BDLCPBSE #SBDLFUT UPHFUIFS VTJOH UXP w Y w Hex Bolts (AAS) UXP w Y w (BMWBOJ[FE 4QBDFST "#4 BOE UXP w Centerlock Nuts (AAB).
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1/2” ABI Y AAJ Y SEC 3.3 "#' Y ABD Y *OTFSU UXP w Y w 5BQ #PMUT "#* XJUI UIF 5/16” Washers (ABD) and the w 3VCCFS 8BTIFST "#' UISPVHI UIF CPUUPN IPMFT JO UIF CBDL PG UIF Rim (ALX) BT TIPXO BOE TFDVSF UIF IBSEXBSF XJUI UXP 5/16” Hex T-Nuts (AAJ). ALX ABD "#' ABI AAJ ALX ABI ABI ! Note: Make sure that the 5/16” x 2 1/4” Tap Bolts are positioned on the outside edge of the holes as shown.
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1/2” AAV Y SEC ABK Y Place the Rim Support Channel (AOX) JO UIF SFDFTT PO UIF CBDLTJEF PG UIF Backboard (AJI) TP UIBU UIF n BU TJEF XJUI IPMFT JT QPTJUJPOFE VQ BHBJOTU UIF #BDLCPBSE BT TIPXO 5IFO JOTFSU UIF w 6 #PMU "06 through the upper IPMFT PO UIF CBDLTJEF PG UIF #BDLCPBSE BT TIPXO AJI AOU AOX SEC 3.
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE AJW Y 1/2” (Not to scale) ABK Y SEC 3.6 Slide the Compression Springs (AJW) onto the w 6 #PMU "06 , and place the Spring Retainer Plate (AOW) over the Compression Springs. Tighten the w /ZMPDL 'MBOHF /VUT "#, until the Rim (ALX) does not XPCCMF UP DPNQMFUF UIJT TUFQ ALX ABK AOW AJW AOU ! Note: DO NOT COMPLETELY TIGHTEN THE 5/16” NYLOCK FLANGE NUTS IN THIS STEP! Only tighten the Nuts until the Rim does not wobble.
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 3/8” ADQ Y SEC 3.
SEC BACKBOARD TO POLE ASSEMBLY HARDWARE REQUIRED Bag BCR Hardware shown at Actual Size ABP Y ABL Y w Y w 1PMZ Spacer w Y w #MBDL Spacer AAX Y w $FOUFSMPDL /VU 6 5/8” (Not actual length) "%( Y w Y w )FY #PMU PARTS REQUIRED Parts shown at 10% of Actual Size 17” AKB Y AKC Y v -POH &YUFOTJPO "SN 4IPSU &YUFOTJPO "SN Part shown at 25% of Actual Size AJY Y Counterbalance Spring TOOLS REQUIRED w 8SFODI Y 7/16” Wrench Y 29 Rubber Mallet
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 7/16” Y /0 )"3%8"3& 3&26*3&% '03 5)*4 1"(& SEC Place one end of the Counterbalance Spring (AJY) PWFS UIF MPXFS w Y w (BMWBOJ[FE 4QBDFS "#4 BT TIPXO ABS AJY ! Note: It may be necessary to use a Rubber Mallet to snap the Counterbalance Spring into place. If the Rubber Mallet does not work , undo the hardware in the image that has been shaded gray. Slide the Counterbalance Spring over the Spacer after it has been detached.
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 6 5/8” w Y "%( Y (Not actual length) AAX Y ABL Y SEC Secure the Short Extension Arms (AKC) UP UIF #BDLCPBSE #SBDLFUT JO UIF MPDBUJPO TIPXO XJUI UIF IBSEXBSF JOEJDBUFE AKC AAX ABL AKC ABL "%( AKC ! Note: Tighten the 1/2” Centerlock Nut (AAX) until it is flush with the end of the Bolt.
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 6 5/8” "%( Y w Y (Not actual length) ABL Y SEC AAX Y Secure the Long Extension Arms (AKB) UP UIF #BDLCPBSE #SBDLFUT JO UIF MPDBUJPO TIPXO XJUI UIF IBSEXBSF JOEJDBUFE AKB AKB AAX "%( ABL ABL AKB ! Note: Tighten the 1/2” Centerlock Nut (AAX) until it is flush with the end of the Bolt.
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 6 5/8” w Y "%( Y (Not actual length) AAX Y ABP Y SEC CAUTION: HAVE ONE ADULT HOLD THE BACKBOARD IN PLACE UNTIL ASSEMBLY HAS BEEN COMPLETED! -BZ UIF #BDLCPBSE BOE 3JN BTTFNCMZ PO UIF HSPVOE OFYU UP UIF Pole assembly. Rest the Rim on cardboard to prevent scratching.
SEC 5 HANDLE ASSEMBLY HARDWARE REQUIRED Hardware shown at Actual Size AAL Y ADJ Y w Y w )FY #PMU w $BQ /VU AAN Y 5/16” Cap Nut AAM Y w Y w 5BQ #PMU ACZ Y w Y w 4QBDFS 6 1/2” (Not actual length) ABB Y ABA Y w $FOUFSMPDL /VU w Y w )FY #PMU 6 5/8” (Not actual length) "%( Y AAX Y w Y w )FY #PMU AQH Y Trigger Spring w $FOUFSMPDL /VU ADR Y ADT Y Y w 1IJMMJQT 1BO )FBE 4DSFX Y w 4DSFX
SEC 5 HANDLE ASSEMBLY PARTS REQUIRED Parts shown at 10% of Actual Size v ALB Y Outer Tube AKQ Y v Inner Channel Parts shown at 25% of Actual Size AKL Y Left Handle AKN Y Right Handle AMN Y Trigger Parts shown at Actual Size "2( Y -PDL 5BC TOOLS REQUIRED Phillips Screwdriver 7/16” Wrench Y w 8SFODI Y 9/16” Wrench Y 35 1/2” Wrench Y
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE ADR Y SEC Secure the -PDL 5BC "2( to the Trigger (AMN) XJUI UIF IBSEXBSF TIPXO 5.1 ADR ADR "2( AMN ! SEC 5.2 Note: Make sure the Lock Tab is oriented as shown when attaching the Tab to the Trigger. Place the Right Handle (AKN) onto the Outer Tube (ALB) so that the notch PG UIF 0VUFS 5VCF m UT XJUIJO UIF )BOEMF BT TIPXO ALB AKN ! Note: Make sure that the Inner Channel (AKQ) has been removed from the Outer Tube before performing this step.
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE ADT Y AQH Y SEC 5.3 Place the Trigger Spring (AQH) onto the Trigger (AMN) BT TIPXO 5IFO QMBDF the Trigger inside the Right Handle (AKN) so that the -PDL 5BC "2( m UT JOUP UIF slot on the Outer Tube (ALB) BT TIPXO ALB "2( AQH AMN AKN ! SEC Note: Pull the Trigger to ensure it moves correctly before attaching the Left Handle (AKL).
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 7/16” Y AAL Y ADJ Y SEC 5.5 Insert the w Y w )FY #PMU ""- through the holes indicated on the Outer Tube (ALB). 4FDVSF UIF w Y w )FY #PMU UP UIF 0VUFS 5VCF XJUI UIF w $BQ /VU "%+ . ADJ AAL ALB 8"3/*/( Do not overtighten the Cap Nut.
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1/2” Y AAM Y SEC 5.6 AAN Y While depressing the Trigger (AMN), insert the notched end of the Inner Channel (AKQ) into the Outer Tube (ALB). Continue to insert the Inner $IBOOFM JOUP UIF 0VUFS 5VCF VOUJM UIF 5SJHHFS DMJDLT JOUP UIF m STU TMPU Then release the Trigger. ALB AKQ ! SEC 5.7 Note: Ensure that the notches on the Inner Channel face the Handle as shown.
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 6 5/8” "%( Y w Y (Not actual length) AAX Y ACZ Y SEC 5.8 Secure the end of the Outer Tube (ALB) to the Long Extension Arms (AKB) XJUI UIF IBSEXBSF TIPXO "%( AAX ACZ AKB ACZ AKB ALB ! Note: Tighten the 1/2” Centerlock Nut (AAX) until it is flush with the end of the Bolt.
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 6 1/2” 9/16” Y (Not actual length) ABA Y SEC 5.9 ABB Y Insert the 3/8” x 6 1/2” Hex Bolt (ABA) through the holes in the Short Extension Arms (AKC) UIBU BSF DMPTFTU UP UIF 1PMF 4FDVSF UIF w Y w )FY #PMU UP UIF 4IPSU &YUFOTJPO "SNT XJUI UIF 3/8” Centerlock Nut (ABB). ABA AKC AKC ABB ! Note: Tighten the 3/8” Centerlock Nut until it is flush with the end of the Bolt.
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Wrench /0 )"3%8"3& 3&26*3&% '03 5)*4 1"(& SEC 5.10 3BJTF UIF #BDLCPBSE UP UIF IJHIFTU QPTJUJPO 6TJOH UIF DMPTFE FOE PG a Wrench, stretch the Counterbalance Spring (AJY) up and over the 3/8” x 6 1/2” Hex Bolt (ABA) BT TIPXO ABA AJY ! Note: Make sure all hardware has been securely tightened before moving to the next section.
SEC 6 '*/"- "44&.
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE /0 )"3%8"3& 3&26*3&% '03 5)*4 1"(& (362 lb) Two adults are required to complete assembly. To prevent serious injuries, the Pole should be held down by one adult at all times while the Base is being filled. SEC 6.1 015*0/ " '*--*/( 8*5) 4"/% (362 lb of sand required) a. Insert a #BTF 1MVH "&' into the Base (AJM) in the hole closest to the Pole.
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE /0 )"3%8"3& 3&26*3&% '03 5)*4 1"(& Two adults are required to complete assembly. To prevent serious injuries, the Pole should be held down by one adult at all times while the Base is being filled. SEC 6.1 015*0/ # '*--*/( 8*5) 8"5&3 a. Insert a #BTF 1MVH "&' into the Base (AJM) in the hole closest to the Pole.
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE /0 500-4 03 )"3%8"3& 3&26*3&% '03 5)*4 1"(& SEC Attach Net (AKZ) to the Rim (ALX). 6.2 ALX AKZ ! SEC 6.3 Note: If a replacement Net is needed, please call our Customer Service Department. Our Nets are shorter than average to reduce the risk of entanglement.
OPERATION OF HEIGHT ADJUSTMENT SYSTEM 5IF CBTLFUCBMM TZTUFN NBZ CF BEKVTUFE GSPN GFFU UP GFFU 0/-: "%6-54 4)06-% "%+645 5)& )&*()5 0' 5)& 4:45&. 50 "%+645 5)& 4:45&.
NOTES
NOTES
ENHANCE YOUR LIFETIME® PURCHASE BY ADDING ACCESSORIES OR OTHER GREAT PRODUCTS: To purchase accessories or other Lifetime Products, visit us at: www.lifetime.
WARNING '"*-63& 50 '0--08 5)&4& 8"3/*/(4 .": 3&46-5 */ 4&3*064 */+63: "/% 03 1301&35: %"."(& 0XOFST NVTU FOTVSF UIBU BMM QMBZFST LOPX BOE GPMMPX UIFTF SVMFT GPS TBGF operation of the system. t 0OMZ IBOH GSPN UIF SJN CSJFn Z UP SFHBJO CBMBODF PS BWPJE JOKVSJOH PUIFST 3FMFBTF the rim as soon as safely possible.
WARRANTY INFORMATION -*'&5*.& #"4,&5#"-- &26*1.&/5 :&"3 -*.*5&% '"$503: 8"33"/5: 5)& ."/6'"$563&3 3&4&37&4 5)& 3*()5 50 .",& 46#45*565*0/4 50 8"33"/5: $-"*.4 *' 1"354 "3& UNAVAILABLE OR OBSOLETE.