MODEL N° 90046 CO PY OWNER’S MANUAL Keep this Product ID Number and use when contacting Customer Service: 1
REGISTER YOUR LIFETIME PRODUCT TODAY! 4HERE ARE BENElTS TO REGISTERING YOUR ,IFETIME PRODUCT 7ITH OUR NEW ONLINE PRODUCT REGISTRATION FORM IT S FAST AND EASY 2EGISTER WITH US AT WWW LIFETIME COM AND ENJOY THESE GREAT BENElTS s 2ECEIVE EXCLUSIVE MONEY SAVING OFFERS FROM "UY,IFETIME COM OUR ONLINE STORE AS WELL as NEW product notifications and special closeout promotions! s )N THE UNLIKELY EVENT OF A PRODUCT RECALL OR SAFETY MODIlCATION WE WILL NOTIFY YOU s 2EGISTERING YOUR PRODUCT GUARANTEES YOU WARRANTY
PARTS LIST ID BZE BZF BZG BZH BZI Item Description Adjustable Goal and Net Assembly Storage Straps Net Straps Stakes Stake Bag Qty 1 2 12* 5 1 PARTS IDENTIFIER Parts not shown to scale BZE (x1) Adjustable Goal and Net Assembly ":' X Net Straps ":& X Storage Straps BZH (x5) Stakes BZI (x1) Stake Bag 3IX .ET 3TRAPS ":' COME PRE ASSEMBLED TO THE 'OAL .ET !SSEMBLY ":% The remaining six (6) Straps are found in the Stake Bag (BZI).
SEC 1 Step 1.1 '/!, 3%450 Remove the 3TORAGE 3TRAPS ":& from the !DJUSTABLE 'OAL AND .ET !SSEMBLY ":% . BZE ":& ":& ! Note: The Net should remain attached to the Assembly. It has been omitted from these images in order to clarify parts handled during setup. ! Note: Do not carry the Adjustable Goal and Net Assembly by the Storage Straps. When folded up, always carry the goal by holding the metal tubing. Step 1.
Step 1.3 Press in the push buttons on the legs on both sides of the Goal. Extend the legs by sliding them out until the push buttons snap into the last hole on the leg. Push Buttons BZE BZE Push Buttons Step 1.4 Raise the front of the Goal to the highest setting by pressing the push buttons in and sliding the legs until the push buttons snap into the highest hole on the leg.
Step 1.5 Unfold the back of the 'OAL AND .ET !SSEMBLY ":% until the unit forms a right ANGLE AS PICTURED ,OCK THE LEGS IN PLACE USING THE PINS ON THE TWO CORNER brackets of the Assembly as shown. BZE Locking Pin on Corner Bracket Step 1.6 Slide the Stakes (BZH) onto the metal tubes and push the ends into the ground by hand in the positions indicated.
SEC 2 '/!, !$*534-%.4 Step 2.1a At full size, the Soccer Goal will measure 7’ wide and 5’ tall. To adjust the size to 6’ x 4’, press the push buttons on the top and rear assembly legs and slide the goal to the middle hole on each tube. Press the push buttons on the side legs and slide the goal to the middle holes on each tube. Middle Hole Push Buttons Push Buttons Middle Hole Step 2.
Step 2.2 Use four .ET 3TRAPS ":' to tighten the Net. Place the Net Straps on the metal tubing of the !DJUSTABLE 'OAL AND .ET !SSEMBLY ":% in the locations shown.
Step Use the remaining two .ET 3TRAPS ":' to gather the excess netting. These straps will not be placed on the metal tubing, but will gather the net to itself. The illustration below shows suggested placement points for the Net Straps. 2.3 ":' ! Note: Use the white sections of the Net as a guide. For a 6’ x 4’ goal, gather the net in from the right side and from the rear until you reach the first white line. For a 4’ x 3’ goal, use the second line.
NOTES 10
ENHANCE YOUR LIFETIME® PURCHASE BY ADDING ACCESSORIES OR OTHER GREAT PRODUCTS: To purchase accessories or other Lifetime Products, visit us at: www.lifetime.
WARRANTY INFORMATION ,)&%4)-% 30/24).' '//$3 $!9 ,)-)4%$ &!#4/29 7!22!.49 4(% -!.5&!#452%2 2%3%26%3 4(% 2)'(4 4/ -!+% 35"34)454)/.3 4/ 7!22!.49 #,!)-3 )& 0!243 !2% UNAVAILABLE OR OBSOLETE. ,IFETIME SPORTING GOODS ARE WARRANTED TO THE ORIGINAL PURCHASER TO BE FREE FROM DEFECTS IN MATERIAL OR workmanship for a period of ninety days from the date of original retail purchase. The word “defects” is defined as imperfections that impair the use of the product.
