Manual

ManualsBrandsLiftMaster ManualsSafetyKPR2000 Single Entry Access Control Keypad and Proximity Reader

WATERPROOF

KEYPAD/PROXIMITY READER

MODEL KPR2000

TABLE OF CONTENTS

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

CARTON INVENTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

ONE YEAR LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

INSTALL THE KPR2000. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

CHOOSE AN OPERATION MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

WIRE THE KPR2000. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . .5

CONFIGURE THE KPR2000. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

PROGRAM CARDS AND PINS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

ADVANCED PROGRAMMING . . . . . . . . . . . . . . . . . . .7

PANIC CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

ALARM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

SOUND & LIGHT INDICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

RESET THE KPR2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

ERASE ALL CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Summary of content (8 pages)

PAGE 1
4 7 * 2 5 8 0 3 6 9 # WATERPROOF KEYPAD/PROXIMITY READER MODEL KPR2000 TABLE OF CONTENTS INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . .2 PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . .5 FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CARTON INVENTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 2
INTRODUCTION The LiftMaster KPR2000 is a single entry multi-function Access Controller with integrated keypad and card reader. It is designed and manufactured to perform in a wide range of indoor, outdoor, and harsh environments. The KPR2000 supports up to 2000 users in multiple access configurations (Card Only, Card or PIN, or Card + PIN). The built in 125 KHz card reader supports HID 26 bit Wiegand and 30 bit Sentex Wiegand proximity card formats.
PAGE 3
INSTALLATION 1 Install the KPR2000. 1 2 3 4 5 6 7 8 9 * 0 # 2 Choose an Operation Mode. STAND ALONE OPERATION PASS-THROUGH OPERATION The KPR2000 functions as a complete access control system. The user database is stored in non-volatile memory, reads the PINs and card codes, performs the authentication, and grants and monitors access to the property or device.
PAGE 4
WIRING 3 Wire the KPR2000.
PAGE 5
PROGRAMMING 4 Conﬁgure the KPR2000. Change the configure settings according to your application (optional). Multiple configuration settings can be changed at one time: enter program mode, change desired settings, then exit program mode. SET MASTER CODE SET DOOR OPEN TOO LONG (DOTL) ALARM The 6 digit Master Code is used to prevent unauthorized access to the system. To interface with the KPR2000, the manager will need a Master Code (factory default code: 888888).
PAGE 6
PROGRAMMING 5 Program Cards and PINS. Programming will vary depending on the access configuration. Follow the instructions according to your access configuration. GENERAL PROGRAMMING INFORMATION • User ID Number: Assign a user ID number to the access code in order to keep track of the users of access cards or PINs. The user ID number can be any number from 1~2000. IMPORTANT: User IDs do not have to be proceeded with any leading zeros. Recording of User ID is critical.
PAGE 7
PROGRAMMING ACCESS CONFIGURATION: CARD ONLY USING MANAGER CARDS Programming Step Keystroke Combination KPR2000 managers can use manager cards to program user cards into and out of the system. There are two pre-programmed manager cards (an Add Card, and a Delete Card) to allow rapid card enrollment. This is a form of Auto User ID enrollment and is only available in “Card Only” configuration. Add a User Card 1. (Read Manager Add Card) 2. (Read User Card) Repeat Step 2 for additional user cards 3.
PAGE 8
ADVANCED PROGRAMMING Alarm Reset the KPR2000 TO RESET THE ALARM This will reset the KPR2000 to the factory default but all card/PIN information will still be retained. This will also require reprogramming of the Master Add and Delete Cards. NOTE: This is useful if the original Master Add and Delete Cards have been lost. 1. Power the KPR2000 down. 2. Press and hold the ✱ button while power is restored to the KPR2000. 3. Release the button and wait until the amber LED shines. 4.