User's Manual

Before
using
your
new
product
,
please
read
these
instructions
to
prevent
any
damage
.
V2 ENGLISH 15-0655
PLAYING MUSIC FROM AN EXTERNAL SOUND
SOURCE
1 Connect an external sound source, such as an MP3 player, by
plugging an audio cable with a 3.5 mm plug (not included) into the
AUX IN jack on the right side of your speaker.
Notes:
• When an AUX cable is connected, Bluetooth goes into standby mode. To play
music from your Bluetooth device, press play ( ) on the speaker or your
Bluetooth device. To return to AUX mode, press pause or stop on the speaker
or your Bluetooth device.
• When playing music via audio cable, you should pause the Bluetooth sound
source paired to your speaker or disconnect the Bluetooth device.
2 Start playback on the external device.
3 Press + or – to adjust the volume.
4 Control playback using the controls on the external device.
TAKING A CALL
1
OR
Press and hold the button to reject an incoming call.
2 Press the button during a call to end the call.
RESETTING THE SPEAKER
Caution: This will remove all paired Bluetooth devices.
• Turn on the speaker, then press and hold the previous button ( )
and the volume up + buttons at the same time for approximately
TROUBLESHOOTING LEGAL NOTICES
FCC
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: 1) this device may not cause harmful
interference, and 2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
to try correct the interference by one or more of the following measures:
- Reorient the receiving antenna.
- Increase the separation between the equipment and receiver.
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
by the party responsible for compliance could void your authority to
operate the equipment.
RSS
IC Statement
This device complies with Industry Canada licence exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation
of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicable
s aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suiv antes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accept er t
out brouillage
radioélectrique subi, même si le brouillage est susceptible d'en comprom
ettre le fonctionnement.
PROBLEM
No power
No sound or low volume
Cannot establish Bluetooth
connection
My Bluetooth device keeps
unpairing
“NS-SPBTBRICK” does not
appear on my Bluetooth
device
SOLUTION
• Make sure that your speaker’s battery is charged.
• Make sure that your speaker is turned on.
• Make sure that your Bluetooth device is turned on, Bluetooth is turned
on, and NS-SPBTBRICK is selected.
• Turn up the volume on your speaker.
• Turn up the volume on your Bluetooth device.
• Make sure that your Bluetooth device is not muted.
• Make sure that your speaker is not paired to another Bluetooth device.
• Make sure that your Bluetooth device is not paired to another Bluetooth
device.
• Shorten the distance between your speaker and your Bluetooth device.
• Make sure that your speaker is in pairing mode. Press and hold the
button to reenter pairing mode.
• Sh
orten the distance between your speaker and your Bluetooth device.
device.
• Make sure that your speaker is not paired to another Bluetooth device.
• Make sure that your speaker and Bluetooth device are both in pairing
mode.
• Make sure that your Bluetooth device supports Bluetooth v4.0 and
below.
• Make sure that your Bluetooth device is not connected to any other
device.
• Make sure that you have selected NS-SPBTBRICK on your Bluetooth
device.
• Make sure that AUX external device is not connected. Disconnect the
AUX cable and reenter pairing mode.
• Shorten the distance between your speaker and your Bluetooth device.
• If the battery on your Bluetooth device is low, recharge the battery.
• If the battery on your speaker is low, r
echarge the battery.
• Shorten the distance between your speaker and your Bluetooth device.
• Put your speaker into pairing mode, then refresh your list of Bluetooth
devices. For more information, see the documentation that came with
your Bluetooth device.
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA:
1-877-467-4289 (U.S. and Canada)
01-800-926-3000 (Mexico)
www.insigniaproducts.com
Distributed by Best Buy Purchasing, LLC
©2015 Best Buy. All rights reserved.
Made in China
NS-SPBTBRICK_15-0655_QSG_V2_EN.ai 2 8/4/2015 2:09:26 PM
RSS-102 Statement:
This equipment complies with Industry Canada radiation exposure
limits set forth for an uncontrolled environment.
Cet équipement est conforme à l'exposition aux rayonnements
Industry Canada limites établies pour un environnement non contrôlé.