User Guide

READANDUNDERSTANDTHESEINSTRUCTIONSBEFOREINSTALLINGFIXTURE
INSTRUCI’IONSHEETNO.
s fixture is intended for installation in accordance with the National Electrical Code and local
ulations. To assure full compliance with local codes and regulations,
check with your local electricalinspector before
ablation.To prevent electrical shock, turn offelecttici~ at fuse box before proceeding,
IS:1920LV
Retain these instructions for maintenance reference.
0892
Page 1 of 2
INSTALLATION PROCEDURE OF LYTECASTER LOW VOLTAGE 1920LV
CONVERSION KIT IN 1000IC, 1000AICM,
1000ICM, 1002P1, 1003 PI, 1900P1
FRAME-IN KITS WITH 1000LV series REFLECTOR TRIMS
WARNING: THIS CONVERSION KIT CAN ONLY CONVERT A 120V INCANDESCENT FRAME-IN KIT INTO A LOW VOLTAGE
FRAME-IN KIT. BEFORE PROCEEDING WITH THE INSTALLATION, IT IS IMPORTANT TO READ THE MARKINGS ON THE
SOCKET CUP OF THE EXISTING FRAME-IN KIT TO DETERMINE THE FRAME-IN KIT CATALOG NUMBER.
IF I.C. TYPE
FRAME-IN KIT IS USED, IT MAY BE INSTALLED IN DIRECT CONTACT WITH INSULATED CEILINGS. IF A NON–I.C. TYPE
FRAME-IN KIT IS USED, DO NOT INSTALL INSULATION WITHIN 3 INCHES OF FIXTURE SIDES, CONVERSION, KIT AND
WIRING COMPARTMENT, NOR ABOVE FIXTURE IN SUCH A MANNER TO ENTRAP HEAT.
REMOVALOFEXISTING REFLECTORTRIM
A Makesure power is off,
B, Removelamp from existing REFLECTORTRIM.
C. Removeexisting REFLECTORTRIM byturning REFLECTOR
TRIM counterclockwisewhile pulling downward.
D. DetachFRAME-lNKIT SOCKETCUP from REFLECTOR
TRIM bysqueezing SOCKETCUP SPRINGS,
INSTALLATIONOF CONVERSIONKIT
WARNING: RISK OF FIRE. ADHERE PROPER(ATTACHED)
WAITAGE LABEL OVER EXISTINGWATrAGE LABEL IN
REFLECTORTRIM AFTER IDENTIFYINGTHE FRAME-INKIT:
FOR 1000IC, 1000AICM, 1000ICM, 1001IC: USE 35W. MAX. LABEL. FOR
1002P1, 1003P1, 1900P1: USE 50W. MAX. LABEL.
A.
B.
c.
Screw MALE ADAPTER of conversionkit into frame-in kit SOCKETCUP
(Fig, A). NOTE: Preturn male adaptor 3-4 times counterclockwise
before screwing into socket cup so as not to stress wire
connections.
Attach frame-in kit SOCKETCUP to conversionkit by insertingSOCKET
CUP SPRINGSinto SLOTS (Fig, B),
For 1002P1,snao CONVERSIONKIT MOUNTINGBRACKETinto
FRAME SIDE (opposite of J-BOX) (Fig. C). To secure CONVERSION KIT
tighten LOCKING SCREW (Fig. C);
For 1000IC & 1000ICM, place
CONVERSION KIT into INSUUTED HOUSING opposite J-BOX (Fig. D);
For1003Pl &1900 Pl, place CONVERS1ONKITtotheside of the
MOUNTINGRING oppositeJ-BOX.
ROTATEROTO-CLIPS(Fig. E)
Rotate (4) ROTO.CLIPSso that the legs extend inwardlyas shown
toward the center opening.
SNAP-IN
}
SEE SEPARATE REFLECTOR
PUSH-UP
TRIM INSTRUCTION SHEETS.
;E BACK PAGE FOR LAMP INSTALLATION
ID TRANSFORMER REPLACEMENT
m
FRAME
MOUNTS FLUSH
ON CEILING MATERIAL
... . . .. .. ..- ..
,- .’.’! . .
CEILING
MATERIAL
POSITION
FIG. E
FI
NVERSION KIT
FIG. B
L“-”
SLOT
FIG C
[ FRAME
~ J-BOX
INSULATED HOUSING n
/-Conversion KIT
FIG. D