Owner's manual

ManualsBrandsLightronics ManualsLightingFXLD836C4I

Page 1 of 6

FXLD836C4I LED FIXTURE

Version 0.1 OWNERS MANUAL 06/06/2013

www.lightronics.com

Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588

FEATURES AND SPECIFICATIONS

LEDS: 36, 8 Watts each (R,G,B,W - 4 in 1)

Beam angle: 25 º

Control system: DMX-512 + Stand Alone Modes

DMX channels: 4/5/7

DMX connectors: 3 pin XLR

Voltage: 120 VAC 50/60Hz

Max power consumption: 320 Watts

Body material: Die Cast Aluminum

Body color: Black

Size: 13"L x 11.5"W x 7.5"H

Weight: 14.3 lbs (7kg)

DESCRIPTION

The FXLD836C4I is a RGBW LED lighting fixture. It

is suitable for stage, disco, night club, and other artistic

applications. It has several stand alone control modes

and can operate via a DMX-512 external signal.

A double yoke enables the fixture to be operated in

several positions.

INSTALLATION

LOCATION

The FXLD836C4I is rated IP20 and is intended for

INDOOR USE ONLY.

Locate the unit in a well ventilated area away from

moisture and heat. Keep the vent holes clear. Holes

are provided on the yokes to install a lighting bar pipe

clamp. Use a safety cable when hanging the fixture.

POWER CONNECTIONS

The FXLD836C4I has a blue powercon style connector

for power input. A compatible power cable is provided

for connection to a 120 VAC, 15 Amp, 60Hz,

grounded service. Push the blue connector on the

cable straight into the blue connector on the unit and

twist aprox. 1/8 turn clockwise to latch it.

The white powercon style connector on the unit is used

to pass power on to another unit. A mating white

connector is also provided.

Caution is advised since the line cord is rated for

aprox. 7 Amps maximum.

THE SAFETY GROUND TERMINAL ON ALL POWER

CABLES MUST BE USED.

DMX CONNECTIONS

A system using DMX control should be connected as a

chain of devices. In other words the control signal

cable should proceed from the controller to the first

receiving device and then to others in a continuous

"daisy chain" fashion.

The fixture has a DMX IN and a DMX OUT connector

to be used to connect the chain. The control cable

should NOT be split into a multiple run star

arrangement with a cable running from the controller

directly to each receiving device pack.

DMX CONNECTOR PIN ASSIGNMENTS

There are two different connectors which can be used

for DMX control. They are both XLR type connectors.

Some units use 3 pin connectors. Others use 5 pin

connectors. The FXLD836C4I receives a DMX signal

on the 3 pin MALE connector on one side of the unit.

The 3 pin FEMALE connector is used to connect the

next DMX device on the control chain.

CAUTION

RISK OF ELECTRIC SHOCK

Summary of content (6 pages)

PAGE 1
Page 1 of 6 FXLD836C4I LED FIXTURE OWNERS MANUAL Version 0.1 06/06/2013 FEATURES AND SPECIFICATIONS LEDS: 36, 8 Watts each (R,G,B,W - 4 in 1) Beam angle: 25 º Control system: DMX-512 + Stand Alone Modes DMX channels: 4/5/7 DMX connectors: 3 pin XLR Voltage: 120 VAC 50/60Hz Max power consumption: 320 Watts Body material: Die Cast Aluminum Body color: Black Size: 13"L x 11.5"W x 7.5"H Weight: 14.3 lbs (7kg) DESCRIPTION The FXLD836C4I is a RGBW LED lighting fixture.
PAGE 2
Page 2 of 6 FXLD836C4I LED FIXTURE OWNERS MANUAL Version 0.1 If your console uses a 5 pin connector you can make up an adapter cable to accommodate this. The table below shows the pin assignments for BOTH the 3 pin and 5 pin connectors. PIN # 1 2 3 4 5 SIGNAL NAME DMX COMMON DMX DATA DMX DATA + NOT USED NOT USED 06/06/2013 DMX OPERATION Use the Addr menu to set the starting address of the unit. You can set the starting address of the unit with the UP and DOWN buttons.
PAGE 3
Page 3 of 6 FXLD836C4I LED FIXTURE OWNERS MANUAL Version 0.1 06/06/2013 MAINTENANCE AND REPAIR CAUTION DO NOT OPEN UNIT RISK OF ELECTRIC SHOCK RISK OF FIRE TROUBLESHOOTING Check that you have power applied to the unit. Check the DMX control cable. Check the address settings of the unit and the controller. CLEANING Do not use harsh chemicals or solvents when cleaning the fixture. A mild detergent can be used sparingly if needed. Ensure that the unit is completely dry before re-use.
PAGE 4
Page 4 of 6 Version 0.1 FXLD836C4I LED FIXTURE OWNERS MANUAL 06/06/2013 MENU NAVIGATION www.lightronics.com Lightronics Inc.
PAGE 5
Page 5 of 6 FXLD836C4I LED FIXTURE OWNERS MANUAL Version 0.1 06/06/2013 DMX VALUES AND FUNCTIONS 4 CHANNEL MODE (MODE A) CHANNEL NO. 1 2 3 4 FUNCTION 0 - 255 Red Level 0 - 255 Green Level 0 - 255 Blue Level 0 - 255 White Level 5 CHANNEL MODE (MODE P) CHANNEL NO.
PAGE 6
WARRANTY This product is warranted for a period of TWO YEARS from the date of purchase against defects in materials and workmanship. This warranty is subject to the following restrictions and conditions: A) If service is required, you may be asked to provide proof of purchase from an authorized Lightronics dealer. B) This warranty is valid only for the original purchaser of the unit.