Product Info

ManualsBrandsLINAK ManualsElectronicsBluetooth Control Box

Page 255 of 264

LIFT50 mounting

Drawing no. 1039w4000

LIFT50 only comply with IPX6 when the control box is mounted correctly

(see illustration 1 and 2).

LIFT50 can be mounted as shown on the pictures above:

• Battery upwards, cable outlets downwards (see illustration 1)

• Control box lying on either side, seen from the front (see illustrations 2)

Cables and blind plugs must be inserted correctly in the control box to maintain the IP degree in washing or cleaning situations.

Recommendations - positioning

Mounting information:

LIFT50 is mounted by means of 2 screws (not supplied by LINAK).

Screw type: ISO7380-1 / M5 and L = 20 mm or 25 mm

Washer type: ISO7089 / M5, d1 = 5.3 mm / d2 = 10 mm / s = 1mm

The LIFT50 control box must be mounted with two screws (se drawing).

The mounting screws for the control box and the charger must be tightened with a

maximum torque of 1 Nm.

Mounting holes

Summary of content (10 pages)

PAGE 1
LIFT50 mounting 2 2 1 Drawing no. 1039w4000 Recommendations - positioning LIFT50 only comply with IPX6 when the control box is mounted correctly (see illustration 1 and 2). LIFT50 can be mounted as shown on the pictures above: • Battery upwards, cable outlets downwards (see illustration 1) • Control box lying on either side, seen from the front (see illustrations 2) Cables and blind plugs must be inserted correctly in the control box to maintain the IP degree in washing or cleaning situations.
PAGE 2
Recommendations - mounting If COL50 is mounted incorrectly, water will gather in the plug holes resulting in possible non-compliance with IPX6. COL50 can be mounted as shown on the pictures below: 1) Batteries up, cable outlets downwards 2) COL50 lying on the side, no difference if mains cable is up or down COL50 – Mounting on patient lifter Move top position in 3 Mounting holes 1 Mount the steel bracket on the patient lift using the two dedicated holes 2 Mount control box (COL50) on steel bracket.
PAGE 3
Recommendations: • • • • • • • • The control buttons of redundant hand controls for lifting and lowering work as normal hand control buttons. The service counter is only active in COL50 when a sufficiently charged BAL50 is mounted. When using a control box with emergency stop, the stop button must be activated in cleaning situations in order to comply with IPX6. Only use original LINAK mains cables to ensure a proper connection to the internal charger.
PAGE 4
5. BAL50 (MEDLINE® CARELINE® ) The BAL50 Li-Ion battery pack is a part of the LIFT50 product series specially developed for patient lifts. LIFT50 is a complete system consisting of the control box COL50, a battery BAL50 and an external charger CHL50 in a flexible solution.
PAGE 5
Warnings ALL LI-ION BATTERY USERS MUST READ THESE IMPORTANT BATTERY SAFETY INSTRUCTIONS AND WARNINGS BEFORE USING LI-ION BATTERIES. Failure to read and follow these safety instructions and warnings may result in fire, personal injury, and equipment damage if the batteries are charged and/or used improperly. Lithium ion batteries differ from the lead acid technology as they have a built-in deep discharge protection.
PAGE 6
. CHL50 (MEDLINE® CARELINE® ) The CHL50 charger is an important part of the LIFT50 family. It functions as a wall charger when mounted on the wall, but also as a more mobile charger simply placed horizontally on its back on any surface.
PAGE 7
Charger mounting When mounting CHL50 on wall, please use the two dedicated mounting holes placed in the charger body. Front View CHL50 must be mounted by means of 2 screws (not supplied by LINAK): Mounting holes Screw type: Diameter 4 mm/style: pan head or truss head. Length and thread type depend on wall material. Washer type: Optional 4 mm washer with max. 10 mm outer diameter. The mounting screws for the control box and the charger must be tightened with a maximum torque of 1 Nm.
PAGE 8
Recommendations: • • • • The charger CHL50 is specifically designed to charge the BAL50 type battery. Special care should be taken when mounting the CHL50. If the CHL50 is mounted correctly, the CHL50 complies to IPX4. If the CHL50 is mounted incorrectly, then water may enter the screw holes resulting in IPX4 non-compliance and cause malfunction and hazardous situations. • In cleaning situations, the charger must be disconnected from mains.
PAGE 9
10. Repair and disposal Repair Only an authorised LINAK® service centre should repair the LINAK actuator systems. Systems to be repaired under warranty must be sent to an authorised LINAK service centre. In order to avoid the risk of malfunction, all actuator repairs must only be carried out by an authorised LINAK Service shop or repairers, as special tools and parts must be used. If a system is opened by unauthorised personel there is a risk that it may malfunction at a later date.
PAGE 10
China Slovakia France LINAK Slovakia s.r.o. Phone: +421 51 7563 444 www.linak.sk LINAK FRANCE E.U.R.L LINAK (Shenzhen) Actuator Systems, Ltd. Phone: +33 (0) 2 41 36 34 34 Fax: +33 (0) 2 41 36 35 00 Phone: +86 755 8610 6656 www.linak.fr Phone: +86 755 8610 6990 www.linak.cn Germany Denmark - Headquarters LINAK A/S - Group Headquarters Phone: +45 73 15 15 15 Fax: +45 74 45 80 48 Fax (Sales): +45 73 15 16 13 www.linak.com Spain LINAK Actuadores, S.L.u Phone: +34 93 588 27 77 Fax: +34 93 588 27 85 www.