Installation Instructions

ManualsBrandsLINAK ManualsElectronicsHB200

Page 188 of 194

13. SLS (MEDLINE

CARELINE

TECHLINE

)

LINAK has designed a switch that can be mounted in connection with the 24V DC actuators: LA12, LA22, LA28,

LA28S, LA31, LA32, or LA34 and a control box on e.g. a bed frame.

The Safety Limit Switch (SLS). The SLS Switch is primarily used as a Limit Switch in systems consisting of a control

box, LA28/28S and/or LA32.

As an example the SLS can be installed on the actuator cable where it disconnects the actuator in either inward or

outward direction when activated. The SLS can also be used as a signal control directly connected to a control box.

The Under Bed Light (UBL) can be mounted under the bed to provide a discrete guiding

light when the patient leaves the bed during night. With an Under Bed Light it is easy to

switch the light on and off by means of a handset or controlling it automatically with the

Out of Bed functionality of the MJB8.

14. Under Bed Light (MEDLINE

CARELINE

)

Usage:

• Operating temperature: + 5 °C to + 40 °C

• Storage temperature: - 10 °C to + 50 °C

• Atmospheric pressure: 700 to 1060hPa (3000 m)

• Approvals: IEC 60601-1, ANSI/AAMI ES60601-1,

CAN/CSA-22.2 No 60601-1

• Connectivity: To be connected to MJB5 and MJB8

Recommendations

• The Under Bed Light (Item P/N.: 0964135) must be mounted on the bed with metal screws in order to maintain ESD protection.

The Under Bed Light (UBL2) provides a powerful light with

a good distribution. The UBL2 is to be used for beds within

hospitals, nursing homes and in homecare.

The Under Bed Light makes it easier for patients and other

people in need of care to ﬁnd their way at night in the dark

to prevent falling accidents and to make them feel safe.

15. Under Bed Light 2 (MEDLINE

CARELINE

)

Usage:

• Operating temperature: + 5 °C to + 40 °C

• Storage temperature: - 10 °C to + 50 °C

• Relative humidity: 20% to 80% - non-condensing

• Atmospheric pressure: 700 to 1060 hPa (3000 m)

• Height above sea level: Max. 3000 meters

• Approvals: EN62471, IEC60601-1

Recommendations and Precautions

• If 2 or more UBL2 products with dimming function are connected to the same application, it is recommended to have a factory reset key to be

able to synchronize the dimming direction and light intensity if one of the UBL2s is replaced.

• Screw holes in application are needed for mounting. Inform the customer to use M4 Ø12 screws with Ø12 washer, when mounting the UBL2.

Max. torque 2.5 Nm.

• Hot-plugging:

Removing or adding any OpenBus™ cables is not allowed when the CB is powered by mains supply!

If needed anyway, follow the below procedure:

1. Remove mains and wait 5 sec.

2. Mount or dismount the required cables

If this procedure is NOT followed, it may result in a damaged OpenBus™ driver circuit. The risk of a damaged circuit increases if the accessory

has a high start current (in rush current).

• There can be a risk of conflict with other OpenBus™ accessories, like HB, ACP, etc. when using the OpenBus™ UBL2, it is therefore

recommended to make a system/bit overview.

• Always use locking mechanism and O-ring

• Sockets not used must be fitted with blind plugs to ensure IP degree

• The UBL2 must be mounted on a plane surface and casing must not be subject to impact or any kind of stress.

Summary of content (7 pages)

PAGE 1
3. SLS (MEDLINE® CARELINE® TECHLINE®) LINAK has designed a switch that can be mounted in connection with the 24V DC actuators: LA12, LA22, LA28, LA28S, LA31, LA32, or LA34 and a control box on e.g. a bed frame. The Safety Limit Switch (SLS). The SLS Switch is primarily used as a Limit Switch in systems consisting of a control box, LA28/28S and/or LA32. As an example the SLS can be installed on the actuator cable where it disconnects the actuator in either inward or outward direction when activated.
PAGE 2
16. WET Sheet (MEDLINE® CARELINE®) The WET Sheet is an OpenBus™ product and is a part of the WET Detection solution. The WET Detection solution consists of the WET Sheet, the MJB8 and a WET Sheet cable. Recommendations • The WET Sheet is a wearing part which is not covered by the standard LINAK warranty The WET Sheet warranty is valid until the product has been put into use • The WET Sheet is not a stand-alone article and must be included as part of an application e.g.
PAGE 3
Approvals An OEM application approval according to EN45501 Typically the LINAK Weighing Solution will be classiﬁed as a “non-automatic weight” system. If a LINAK Weighing Solution system is applied to a bed AND classiﬁed as such, the system MUST be “ﬁrst-time” veriﬁed and sealed. The veriﬁcation and sealing is typically carried out in one of two ways: 1. Veriﬁcation by the Bed manufacturer himself. It prescribes that the manufacturer is certiﬁed to carry out the veriﬁcation.
PAGE 4
Mounting bracket (frame ﬂat) Article No. 1015W1001: Mounting bracket (frame ﬂat) w/M4 nuts Article No. 1015W9009: Drawing No.: 1015W1009 Drawing No.: 1015W4001 It is recommended to mount the QLCI2 in a position that allows water to escape. Recommended torque: 0.6 Nm +/-0.1 The bracket can be mounted to the bed frame or any other application by means of one of the following mounting procedures: 1) M6 nut to be placed in bracket and ﬁxed with M6 bolt from the rear side.
PAGE 5
Mounting of cables and cable lock: The QLCI2 have a uniquely designed cable lid. The lid also works as an integrated cable lock when closed. 1. 2. 3. 4. 5. Mount load cell cable plugs in QLCI2 Calibrate the system Mount blind plug in calibration port Close lid until lock snaps into place Place calibration void label To allow free access to the cables, the lid has a rest position when completely opened.
PAGE 6
9. Repair and disposal Repair Only an authorised LINAK® service centre should repair the LINAK actuator systems. Systems to be repaired under warranty must be sent to an authorised LINAK service centre. In order to avoid the risk of malfunction, all actuator repairs must only be carried out by an authorised LINAK Service shop or repairers, as special tools and parts must be used. If a system is opened by unauthorised personel there is a risk that it may malfunction at a later date.
PAGE 7
FACTORIES DISTRIBUTORS China Denmark - Sales Norway Argentina LINAK (Shenzhen) Actuator Systems, Ltd. Phone: +86 755 8610 6656 Phone: +86 755 8610 6990 E-mail: sales@linak.cn www.linak.cn LINAK DANMARK A/S Phone: +45 86 80 36 11 Fax: +45 86 82 90 51 E-mail: linak@linak-silkeborg.dk www.linak.dk LINAK Norge AS Phone: +47 32 82 90 90 E-mail: info@linak.no www.linak.no NOVOTEC ARGENTINA SRL Phone: 011-4303-8989 / 8900 Fax: 011-4032-0184 E-mail: info@novotecargentina.com www.novotecargentina.