RETURN TO MAIN MENU IM10082 VIKING™ 1840 SERIES AUTO-DARKENING HELMETS October, 2010 GRAPHICS MAY VARY OPERATOR’S MANUAL Copyright © Lincoln Global Inc. • World's Leader in Welding and Cutting Products • • Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.
IM10082 VIKING™ 1840 SERIES AUTO-DARKENING HELMETS October, 2010 GRAPHICS MAY VARY OPERATOR’S MANUAL Copyright © Lincoln Global Inc. • World's Leader in Welding and Cutting Products • • Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.
SAFETY WARNINGS – READ BEFORE USING WARNING HELMET INFORMATION This Auto-Darkening Welding Helmet will automatically change from a light state (shade DIN4) to a dark state (shade DIN9-13) when arc welding starts. The filter automatically returns to a light state when the arc stops. ARC Rays can injure eyes and burn skin • Before welding, always inspect helmet and filter lens to be sure they are fitted properly, in good condition and not damaged.
SAFETY WARNINGS – READ BEFORE USING WARNING HELMET INFORMATION This Auto-Darkening Welding Helmet will automatically change from a light state (shade DIN4) to a dark state (shade DIN9-13) when arc welding starts. The filter automatically returns to a light state when the arc stops. ARC Rays can injure eyes and burn skin • Before welding, always inspect helmet and filter lens to be sure they are fitted properly, in good condition and not damaged.
SPECIFICATIONS LCD Viewing Area OPERATING INSTRUCTIONS Headgear Adjustment 96 x 47mm (3.78 x 1.85in.) Adjustment Fore-Aft Adjustment Tilt Knob Ratchet Adjustment Crown Cartridge size 110 x 90mm (4.33 x 3.54in.
SPECIFICATIONS LCD Viewing Area OPERATING INSTRUCTIONS Headgear Adjustment 96 x 47mm (3.78 x 1.85in.) Adjustment Fore-Aft Adjustment Tilt Knob Ratchet Adjustment Crown Cartridge size 110 x 90mm (4.33 x 3.54in.
ALWAYS TEST TO BE SURE THE ADF CARTRIDGE IS CHARGED BEFORE WELDING. The helmet can be placed in sunlight to charge. Do not store the helmet in a dark cabinet or other storage area for long periods. While welding, the arc also charges the ADF cartridge. CARTRIDGE OPERATION/FEATURES Variable Shade Control The shade can be adjusted from shade 9 to 13 based upon welding process or application (refer to Shade selection chart on page 6).
ALWAYS TEST TO BE SURE THE ADF CARTRIDGE IS CHARGED BEFORE WELDING. The helmet can be placed in sunlight to charge. Do not store the helmet in a dark cabinet or other storage area for long periods. While welding, the arc also charges the ADF cartridge. CARTRIDGE OPERATION/FEATURES Variable Shade Control The shade can be adjusted from shade 9 to 13 based upon welding process or application (refer to Shade selection chart on page 6).
CARTRIDGE AND LENS REPLACEMENT TROUBLESHOOTING GUIDE Replacing Front Clear Cover Lens: Replace the front cover lens if it is damaged. Remove ADF holder assembly per Figure 1. Remove front cover lens from helmet assembly. Carefully remove gasket from cover lens. Install new cover lens into gasket and assemble to helmet shell. Make sure to assemble cover lens and gasket into helmet shell the same way as it was removed.
CARTRIDGE AND LENS REPLACEMENT TROUBLESHOOTING GUIDE Replacing Front Clear Cover Lens: Replace the front cover lens if it is damaged. Remove ADF holder assembly per Figure 1. Remove front cover lens from helmet assembly. Carefully remove gasket from cover lens. Install new cover lens into gasket and assemble to helmet shell. Make sure to assemble cover lens and gasket into helmet shell the same way as it was removed.
WARRANTY INFORMATION WARRANTY INFORMATION: Reference IMWS1 included in Literature. SPATTER DAMAGE IS NOT COVERED BY WARRANTY: Do not use this product without the correct protective clear lenses installed properly on both sides of the Auto-Darkening Filter cartridge (ADF). The clear lenses supplied with this helmet are properly sized to work with this product and substitutions from other suppliers should be avoided. REPLACEMENT PARTS 6 1 7 2 3 8 4 4 7 1 2 3 8 6 ITEM PART NO.
WARRANTY INFORMATION WARRANTY INFORMATION: Reference IMWS1 included in Literature. SPATTER DAMAGE IS NOT COVERED BY WARRANTY: Do not use this product without the correct protective clear lenses installed properly on both sides of the Auto-Darkening Filter cartridge (ADF). The clear lenses supplied with this helmet are properly sized to work with this product and substitutions from other suppliers should be avoided. REPLACEMENT PARTS 6 1 7 2 3 8 4 4 7 1 2 3 8 6 ITEM PART NO.