User Guide

C-2
ACCESSORIES
C-2
K1758-”L” INPUT CABLE ASSEM-
BLY
Consists of an 8-conductor control cable with a 14-pin
plug, a 6-conductor control cable with a 10-pin plug,
and an electrode cable with Twist-Mate™ connector.
It is rated at 300 amps, 60% duty cycle and is avail-
able in lengths of 10 ft. (3 mm), 25 ft. (7.6 m), and 50
ft. (15 m).
K2147 CONTROL CABLE AND
WELD CABLE
Consists of an 8-conductor control cable with a 14-pin
plug, a 6-conductor control cable with a 10-pin plug,
and a co-axil weld cable. It is rated at 300 amps, 60%
duty cycle and is available in lengths of 75 ft. (22.6m),
100 ft. (30m).
K659-1 GAS GUARD REGULATOR
Adjustable flow regulator with removable adjustor key
for CO2 and Argon blend gases. Mounts onto wire
drive gas inlet, and reduces gas waste and arc start
"blow" by reducing surge caused by excess pressure
in supply hose.
K590-4 WATER CONNECTION KIT
(For 10 Series Wire Drive Only)
Install per the instructions shipped with the kit.
K682-2 WATER CONNECTION KIT
(K679 Synergic 7F Wire Drive Only)
Install to either side of wire feed unit mounting bracket
per instructions shipped with the kit.
K683-1 DUAL PROCEDURE SWITCH
- Requires K686-2 Adapter for STT-10. Kit includes
gun switch, and mountings for Lincoln Innershield and
Magnum guns, with 15 ft. (4.5 m) control cable and 3-
pin plug. K686-2 Adapter permits 3-pin plug and 5-pin
gun trigger plug to be connected to STT-10 5-pin
Trigger/Dual Procedure receptacle.
K683-3 DUAL PROCEDURE SWITCH
Kit includes gun switch, and mountings for Lincoln
Innershield and Magnum guns, with 15 ft. (4.5m) con-
trol cable and 5-pin plug with two leads to connect to
gun trigger.
K1558-1 REMOTE SWITCH
INTERFACE MODULE
The Module provides for user interface connection of
an external switch (flow switch, etc.) which must be
closed to enable the feeder welding operation.
Also, the Module provides for interface connection of
external equipment (fume extractor, etc.) to the
Moduleʼs isolated relay contacts which actuate when
the feeder welding gas solenoid is activated (repre-
senting welding operation in process).
K1561-1 ROBOTICS INTERFACE
MODULE
The module plugs directly into the STT-10 control
board and provides an interface to a properly
equipped Fanuc robot. (ArcTool software and an addi-
tional process I/O board are needed). When installed
and properly configured, the K1561-1 Robotics
Interface Module allows complete control of the weld-
ing process form the robot controller.
The Lincoln Electric Companyʼs Automation Center
should be contacted for questions regarding installa-
tion or operation of the Robotics Interface Module.
K1557-1 SWIVEL MOUNT
The K1557-1 Swivel mount attaches to the power
source. This kit includes a feeder adapter plate that
allows the feeder to rotate on top of the power source.
The feeder can be easily separated from the swivel
mount at any time. This option is compatible with the
K1556-1 Light Duty Caster Kit.
K1556-1 LIGHT DUTY CASTER KIT
This option provides 4 casters and all required hard-
ware to mount it to the Power Feed 10. This option is
compatible with the K1557-1 Swivel Mount.
K1555-1 INSULATED LIFT HOOK
For applications where an insulated lift hook is
required. This kit provides an easily installed, heavy
duty insulated lift eye that mounts to the wire reel
stand mast. See the instructions provided with the kit
for installation.
SPINDLE ADAPTERS:
K162H (Not required for STT-10 Bench Models)
Spindle for boom mounting Readi-Reels and 2" (51
mm) I.D. spools with 60 lb. (27.2 kg) capacity. User
mounted to appropriately prepared boom framework.
Includes an easily adjustable friction brake for control
of overrun.
When a 2" (51 mm) spindle is used with Readi-Reels
or coils not on 12" (305 mm) O.D. spools, an adapter
is required:
STT-10