User Guide
A-1
INSTALLATION
STT-10
A-1
TECHNICAL SPECIFICATIONS – STT-10 Heads & Controls
WIRE DRIVE OR WIRE DRIVE SECTION OF FEEDER
SPEC.# TYPE LOW SPEED RATIO HIGH SPEED RATIO
• Excluding Wire Reel
∆ Included with K1568-Series STT-10 Boom Package
*Synergic 7F drives use 4-roll drives with 2 driven rolls(Drive roll kits not common with 10 Series heads)
Wire Size Wire Size
Speed Solid Cored Speed Solid Cored
K1563-1∆, 10 Series 35-500 IPM .025 - 3/32 in. .030 - .120 in
K1563-3 Boom Mount (0.89-12.7 m/m) (0.6 - 2.4 mm) (0.8 - 3.0 mm)
K679-1 Synergic 7F* 50 - 770 IPM .025 - 1/16 in. .035 - 5/64 in.
Std Drive
Boom Mount (1.27 - 19.5 m/m) (0.6 - 1.6 mm) (0.9 - 2.0 mm)
K679-2 Synergic 7F* --- --- --- 80 - 1200 IPM .025 - .045 in. .035 - .045 in.
Hi-Speed
Boom Mount (2.00 - 30.5 M/M) (0.6 - 1.2 mm) (0.9 - 1.2 mm)
K1560-1,-2 STT-10 35-500 IPM .025 - 3/32 in. .030 - .120 in.
Bench Model (0.89-12.7 m/m) (0.6 - 2.4 mm) (0.8 - 3.0 mm)
CONTROLS, HEADS AND COMPLETE UNITS
SPEC.# TYPE INPUT POWER PHYSICAL SIZE• TEMPERATURE RATING
Dimensions
Height Width Depth Weight Operating Storage
K1565-1∆ 40-42 Vac ± 10%
Controls STT-10 4.0 Amps 50/60 Hz 14.80 “ 14.20 “ 4.20 “ 18.0 Lbs
K1565-2 Controls 40-42 Vac ± 10% (375.9 mm) ( 360.7mm) (106.7 mm) (8.2 Kg)
Controls 6.0 Amps 50/60 Hz
K1568-1∆ 10 Series 7.81 “ 14.71 “ 11.00“ 25.0Lbs
Std Drive Boom Mount (198.4 mm) (373.6 mm) (27.94 mm) (11.3 Kg)
+40°C +40°C
to to
K679-1,-2 Synergic 7F* 11.5“ 7.16“ 8.06“ 16.5 Lbs -20°C -40°C
Std Drive Boom Mount ( 285.8mm) (181.9 mm) (204.7mm) (7.5 Kg.)
K1560-1 40-42 Vac ± 10%
Std Feeder
4.0 Amps 50/60 Hz
STT-10 20.46 “ 14.43 “ 30.35 “ 65.0 Lbs
K1560-2 Bench Model 40-42 Vac ± 10% (519.7 mm) (366.5 mm) (770.9 mm) (29.5 Kg)
Std Feeder
6.0 Amps 50/60 Hz
GENERAL DESCRIPTION
The STT-10 is a modular line of 42VAC input 4-roll wire
feeders. A single control with dual procedure presettability
of wire feed speed (in IPM or M/min), peak current, and
background current is used with the STT-II power source.
Preset Ranges can be set independently for each procedure
for peak current, background current, and wire feed speed.
The STT-10 models have controls providing keypad or
remote selectability of either of two procedures.
The units offer 4 independently selectable gun trigger
modes for each procedure; cold feed, 2 step and 4-step trig-
ger and spot weld mode.
Also, 4 selectable, presettable timers for each procedure;
preflow, postflow, burnback and spot weld time.
Arc starting can be optimized for each procedure with 5
selectable wire feed acceleration rates, and independent
control of slower run-in procedure.
A gas purge key is provided, as well as cold feed forward
and reverse keys with adjustable forward feed speed setting.
Allot these features are selected with a tactile-feel keypad,
and are set independently using one of two rotating knob
encoders, setting levels are displayed on one of two digital
LED displays.