Manual
!&''"!
*%%*%& "&
'!&#'"!&
:=B;6A@
!#('J&!#&"!,
%'"('#('
"('#('
&A.;1.?1 )<9A.42?2>B2;0F ;=BAB??2;A
120 V / 60 Hz 20 Amps @ rated output
BAF
F092 B??2;A )<9A.42.A%.A21:=2?2@
20% Duty Cycle 90 Amps 19
*2916;4B??2;A%.;42 .E6:B:"=2;6?0B6A)<9A.42 *6?2&=221%.;42
30-125 Amps 33 V 50 - 500 in/min.
(1.3 - 12.7 m/min.)
;=BA)<9A.42?2>B2;0F B@2<??2.82?&6G2
;=BA:=@ #<D2?<?1EA2;@6<;<?1
120 V 60 Hz 20 Amp 20 15 Amp, 125 V,
3 Conductor # 12 AWG
Three Prong Plug (4mm
2
) or Larger
(NEMA Type 5-15P) up to 50 ft.(15.2m)
%" !!#('!(&&-&
2645A *61A5 2=A5 *2645A
13.7 in 10.15 in 17.9 in 48 Ibs
347 mm 258 mm 454 mm 21.7 kg
#,& !&"!&
If connected to a circuit protected by fuses use Time Delay Fuse marked “D”.
&'&('"'"!
Locate the welder in a dry location where there is free
circulation of clean air into the louvers in the back and
out the front of the unit. A location that minimizes the
amount of smoke and dirt drawn into the rear louvers
reduces the chance of dirt accumulation that can
block air passages and cause overheating.
&'!
WIRE FEEDER WELDER(125, 140, 180 MODELS)
cannot be stacked.
''!
Each machine must be placed on a secure, level sur-
face, directly or on recommended cart. The machine
may topple over if this procedure is not followed.
%2.1 2;A6?2 6;@A.99.A6<; @20A6<; /23<?2 @A.?A6;4
6;@A.99.A6<;
&',#%('"!&
'%&"0.;8699
H";9F>B.963621=2?@<;;29@5<B91=2?3<?:
A56@6;@A.99.A6<;
H";9F=2?@<;;29A5.A5.C2?2.1.;1B;12?
@A<<1A52#"*% "=2?.A6;4 .;B.9
@5<B916;@A.99.;1<=2?.A2A56@2>B6=:2;A
H .056;2:B@A/2=9B44216;A<.?202=A.092
D56056@4?<B;121=2?.;F;.A6<;.99<0.9
<?<A52?.==960./922920A?60.90<12@
H'52#"*% =<D2?@D6A056@A</26;
A52"K"L=<@6A6<;D52;6;@A.996;4
D<?80./92.;14B;.;1D52;0<;;20A6;4
=<D2?0<?1A<6;=BA=<D2?
*%!!
%2>B6?2:2;A@<? .E6:B:"BA=BA
In order to utilize the maximum output capability of
the machine, a branch circuit capable of 25 amps at
120 volts, 60 Hertz is required.










