Operator’s Manual RANGER ® 305D (CE) For use with machines having Code Numbers: 11458, 11459, 11587, 12486 Register your machine: www.lincolnelectric.com/register Authorized Service and Distributor Locator: www.lincolnelectric.com/locator Need Help? Call 1.888.935.3877 to talk to a Service Representative Hours of Operation: 8:00 AM to 6:00 PM (ET) Mon. thru Fri. Save for future reference Date Purchased After hours? Use “Ask the Experts” at lincolnelectric.
THANK YOU FOR SELECTING A QUALITY PRODUCT BY LINCOLN ELECTRIC. Please examine Carton and equiPment For damage immediately When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, claims for material damaged in shipment must be made by the purchaser against the transportation company at the time the shipment is received. saFety dePends on you Lincoln arc welding and cutting equipment is designed and built with safety in mind.
SAFETY SECTION A: WARNINGS 1.d. Keep all equipment safety guards, covers and devices in position and in good repair.Keep hands, hair, clothing and tools away from V-belts, gears, fans and all other moving parts when starting, operating or repairing equipment. CALIFORNIA PROPOSITION 65 WARNINGS Diesel Engines 1.e. In some cases it may be necessary to remove safety guards to perform required maintenance.
SAFETY ELECTRIC SHOCK CAN KILL. ARC RAYS CAN BURN. 3.a. The electrode and work (or ground) circuits are electrically “hot” when the welder is on. Do not touch these “hot” parts with your bare skin or wet clothing. Wear dry, hole-free gloves to insulate hands. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards. 3.b.
SAFETY WELDING AND CUTTING SPARKS CAN CAUSE FIRE OR EXPLOSION. CYLINDER MAY EXPLODE IF DAMAGED. 7.a. Use only compressed gas cylinders containing the correct shielding gas for the process used and properly operating regulators designed for the gas and pressure used. All hoses, fittings, etc. should be suitable for the application and maintained in good condition. 6.a. Remove fire hazards from the welding area. If this is not possible, cover them to prevent the welding sparks from starting a fire.
safety v ! v ! !! !! " +!! )+ ,) ", %((" )((% &) +& "+ *!!" )* '(() &' #& %# $% #$ "# "-./01023/!4-!25615.70/8!9!:5615.70/;/<=-<2>-060?@6?! "#$%&#'%&()*!%+!'&#,,)*! -.!/01!&2345!6477489:7!;!<=>.!HG!I.!>G!GG!;!+/C!F!G>!HG!I.!>-!HJ! N/79O/PQ1!F! *+,-.*,)/*/-01+-)-.234,5) *+,&-.+/0!(! --=G>!*/:7Q!AE/:5!#04R! 1)&20)33)&! A")S)"#KT! %U:2!JJ><<;>>..! V*#) #??E:P/7Q!!F! *+,-.*,)/*/-01+-)-.234,5) ;)$+/8)#&!(! --=G>!*/:7Q!AE/:5!#04R! 7/0&+520)33)&! A")S)"#KT! %U:2!JJ><<;>>..
safety vii vii Electromagnetic Compatibility (EMC) Conformance Products displaying the CE mark are in conformity with European Community Council Directive of 15 Dec 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility, 2004/108/EC. It was manufactured in conformity with a national standard that implements a harmonized standard: EN 60974-10 Electromagnetic Compatibility (EMC) Product Standard for Arc Welding Equipment.
safety viii viii Electromagnetic Compatibility (EMC) The size of the surrounding area to be considered will depend on the structure of the building and other activities that are taking place. The surrounding area may extend beyond the boundaries of the premises. Methods of Reducing Emissions Mains Supply Welding equipment should be connected to the mains supply according to the manufacturer’s recommendations.
x taBLe Of CONteNts Page Installation.......................................................................................................................section a Technical Specifications.......................................................................................................A-1 Safety Precautions ........................................................................................................A-2 Location and Ventilation.............................................................
xi taBLe Of CONteNts Maintenance......................................................................................................section D Safety Precautions ................................................................................................D-1 Routine Maintenance ............................................................................................D-1 Engine Maintenance Components ........................................................................D-1 Kubota Diesel Engine ....
INstaLLatION a-1 a-1 teCHNICaL sPeCIfICatIONs - RaNGeR® 305D (Ce)(K2279-1, K2279-2, K2279-3) Make/Model Kubota(3) D722 INPUt - DIeseL eNGINe Description speed (RPM) 3 cylinder, 4 stroke 15.9 HP (12 KW) Net intermittent 3000 RPM naturally aspirated water cooled Diesel engine Welding Process High Idle 3100 Full Load 3000 Low Idle 2200 Displacement cu. in. (cu. cm.) 43.88(789) starting system 12VDC Battery & Fuel: starter 45L (12 US.gal.) Bore x Stroke inch (mm) Oil: 3.2L(3.4 US. Qts.) 2.64 x 2.
a-2 safety PReCaUtIONs WaRNING INstaLLatION Do not attempt to use this equipment until you have thoroughly read the engine manufacturer’s manual supplied with your welder. It includes important safety precautions, detailed engine starting, operating and maintenance instructions, and parts lists. -----------------------------------------------------------------------eLeCtRIC sHOCK can kill. • Do not touch electrically live parts or electrode with skin or wet clothing.
INstaLLatION a-3 tOWING Check with distributor for the recommended trailer for use with this equipment for road, in-plant and yard towing by a vehicle. If the user adapts a non-Lincoln trailer, he must assume responsibility that the method of attachment and usage does not result in a safety hazard nor damage the welding equipment. Some of the factors to be considered are as follows: 1. Design capacity of trailer vs. weight of Lincoln equipment and likely additional attachments. 2.
a-4 eNGINe COOLING systeM WaRNING INstaLLatION ReMOte CONtROL air to cool the engine is drawn in the base sides and exhaust through radiator & case back. It is important that the intake and exhaust air is not restricted. allow a minimum clearance of 0.6m (2 feet) from the case back and 40cm (16”) from either side of the base to a vertical surface.
INstaLLatION a-5 When this welder is mounted on a truck or trailer, its frame must be electrically bonded to the metal frame of the vehicle. Use a #8 or larger copper wire connected between the machine grounding stud and the frame of the vehicle. When this engine driven welder is connected to premises wiring such as that in a home or shop, its frame must be connected to the system earth ground. See further connection instructions in the section entitled "Standby Power Connections" .
a-6 INstaLLatION • the installation complies with the National electrical Code and all other applicable electrical codes. • the premises is isolated and no feedback into the utility system can occur. Certain laws require the premises to be isolated before the generator is linked to the premises. Check your local requirements.
a-7 INstaLLatION Connection of LN-742 and Cobramatic to RaNGeR® 305D (Ce). • Shut the welder off. • Connect per instructions on the appropriate connection diagram in Section F.
B-1 safety PReCaUtIONs WaRNING OPeRatION Do not attempt to use this equipment until you have thoroughly read the engine manufacturer’s manual supplied with your welder. It includes important safety precautions, detailed engine starting, operating and maintenance instructions, and parts lists. -----------------------------------------------------------------------eLeCtRIC sHOCK can kill. • Do not touch electrically live parts or electrode with skin or wet clothing.
OPeRatION B-2 16 1 B-2 15 2 17 3 14 13 12 11 4 10 9 8 5 fIGURe B.1 WeLDING CONtROLs (figure B.1) 1. OUtPUt CONtROL: The OUTPUT dial is used to preset the output voltage or current as displayed on the digital meters for the four welding modes. When in the CCSTICK, or CV-WIRE modes and when a remote control is connected to the 6-Pin or 14-Pin Connector, the autosensing circuit automatically switches the OUTPUT CONTROL from control at the welder to the remote control.
B-3 OPeRatION 4. aRC CONtROL: The ARC CONTROL dial is active in the CV-WIRE, CC-STICK and DOWNHILL PIPE modes, and has different functions in these modes. This control is not active in the TIG mode. CC-stICK mode: In this mode, the ARC CONTROL dial sets the short circuit current (arc-force) during stick welding to adjust for a soft or crisp arc. Increasing the dial from –10 (soft) to +10 (crisp) increases the short circuit current and prevents sticking of the electrode to the plate while welding.
B-4 OPeRatION 15. eLeCtRIC fUeL GaUGe- Provides accu. rate, reliable indication of how much fuel is in the tank. 16. eNGINe HOUR MeteR – Displays the total time that the engine has been running. This meter is useful for scheduling prescribed maintenance. 17. eNGINe PROteCtION LIGHt-A warning indicator light for Low Oil Pressure and/or Coolant Over Temperature. The light is off when the systems are functioning properly.
OPeRatION B-5 WeLDeR OPeRatION DUty CyCLe Duty Cycle is the percentage of time the load is being applied in a 10 minute period. For example a 60% duty cycle, represents 6 minutes of load and 4 minutes of no load in a 10 minute period. The RANGER® 305D (CE) can be used with a broad range of DC stick electrodes.
OPeRatION B-6 B-6 When in the TOUCH START TIG mode and when a Amptrol is connected to the 6-pin Connector the OUTPUT dial is used to set the maximum current range of the CURRENT CONTROL of the Amptrol. For any electrodes the procedures should be kept within the rating of the machine. For additional electrode information see WWW.Lincolnelectric.com or the appropriate Lincoln publication. The RANGER® 305D (CE) can be used in a wide variety of DC TIG welding applications.
C-1 aCCessORIes fIeLD INstaLLeD OPtIONs / aCCessORIes K704 aCCessORy set - Includes (10m) 35 ft. of electrode cable and (9.m) 30 ft. of work cable, headshield, work clamp electrode holder. Cables are rated at 400 amps, 100% duty cycle. K857 (7.6m) 25 ft. or K857-1 (30.4m) 100 ft. ReMOte CONtROL - Portable control provides same dial range as the output control on the welder. Has a convenient 6 pin plug for easy connection to the welder.
D-1 safety PReCaUtIONs WaRNING MaINteNaNCe KUBOta D722 DIeseL eNGINe FREQUENCY • Have qualified personnel do all maintenance and troubleshooting work. • turn the engine off before working inside the machine or servicing the engine. • Remove guards only when necessary to perform maintenance and replace them when the maintenance requiring their removal is complete. If guards are missing from the machine, obtain replacements from a Lincoln Distributor. (see Operating Manual Parts List.
D-2 MaINteNaNCe D-2 eNGINe OIL CHaNGe Drain the engine oil while the engine is warm to assure rapid and complete draining. It is recommended that each time the oil is changed the oil filter be changed as well. OIL fILteR CHaNGe • Drain the oil. • Locate oil drain hose and valve in bottom of base and pull through the hole in the battery access panel on the welder. • Clean the filter mounting base and coat the gasket of the new filter with clean engine oil. • Be sure the unit is off.
D-3 MaINteNaNCe RaNGeR® 305D (Ce) D-3
D-4 COOLING systeM WaRNING MaINteNaNCe D-4 fUeL HOt COOLaNt can burn skin. • Do not remove cap if radiator is hot. -----------------------------------------------------------------------Check the coolant level by observing the level in the radiator and recovery bottle. Add 50/50 antifreeze / water solution if the level is close to or below the "LOW" mark. do not fill above the "FULL" mark. Remove radiator cap and add coolant to radiator.
MaINteNaNCe D-5 fUeL fILteR 1. Check the fuel filter and fuel pre-filter for water accumulation or sediment. 2. Replace the fuel filter if it is found with excessive water accumulation or sediment. Empty fuel prefilter. OVeRsPeeD Is HaZaRDOUs the maximum allowable high idle speed for this machine is 3150 RPM, no load. Do NOt tamper with governor components or setting or make any other adjustments to increase the maximum speed.
D-6 WeLDeR / GeNeRatOR MaINteNaNCe MaINteNaNCe stORaGe: Store the RANGER® 305D (CE) in clean, dry protected areas. CLeaNING: Blow out the generator and controls periodically with low pressure air. Do this at least once a week in particularly dirty areas. BRUsH ReMOVaL aND RePLaCeMeNt: It’s normal for the brushes and slip rings to wear and darken slightly. Inspect the brushes when a generator overhaul is necessary. CaUtION • Do not attempt to polish slip rings while the engine is running.
e-1 tROUBLesHOOtING HOW tO Use tROUBLesHOOtING GUIDe e-1 WaRNING Service and Repair should only be performed by Lincoln Electric Factory Trained Personnel. Unauthorized repairs performed on this equipment may result in danger to the technician and machine operator and will invalidate your factory warranty. For your safety and to avoid Electrical Shock, please observe all safety notes and precautions detailed throughout this manual.
e-2 tROUBLesHOOtING Observe all Safety Guidelines detailed throughout this manual PROBLeMs (syMPtOMs) POssIBLe CaUse Major Physical or Electrical Damage 1. Contact your local Lincoln is Evident. authorized field service facility. Engine will not "crank". 1. Battery is low, Charge Battery. 2. Loose battery cable connections. Inspect, clean and tighten terminals. 3. Faulty engine starter motor. Contact authorized local Engine Service Shop. Engine will "crank" but not start. 1.
e-3 tROUBLesHOOtING Observe all Safety Guidelines detailed throughout this manual PROBLeMs (syMPtOMs) POssIBLe CaUse Engine shuts down while under a 1. High radiator coolant temperaload. ture. Reduce load if it is exceeding machine rating. Add coolant to system if low. Clean fins on radiator if dirty. Tighten fan belt if loose. Remove objects blocking or close to intake openings on both sides of base and exhaust end (case back). Engine runs rough. Battery does not stay charged.
e-4 Observe all Safety Guidelines detailed throughout this manual PROBLeMs (syMPtOMs) Engine will not go to high idle when using auxiliary power. Engine will not go to high idle under weld or auxiliary loading. Engine does not develop full power. Engine runs rough. Engine will not go to high idle when attempting to weld or using auxiliary power. Switching to manual high idle does not work. Engine will not shut off. tROUBLesHOOtING POssIBLe CaUse 1. Auxiliary power load is less than 100 watts.
e-5 tROUBLesHOOtING Observe all Safety Guidelines detailed throughout this manual PROBLeMs (syMPtOMs) POssIBLe CaUse No welding power output. Auxiliary Power OK. 1. Poor work lead connection to work. Make sure work clamp is tightly connected to clean base metal. 2. "Weld Terminals" switch in wrong position. Place switch in "Weld Terminals On" position when welding without control cable. 3. Faulty PC board. Welder has output but no control. 1.
e-6 tROUBLesHOOtING Observe all Safety Guidelines detailed throughout this manual PROBLeMs (syMPtOMs) POssIBLe CaUse ReCOMMeNDeD COURse Of aCtION e-6 The welding arc is “cold.” The weld- 1. Make sure the MODE selector ing arc is not stable or is not satis- switch is in the correct position for factory. the engine runs normally. the process being used. (For examThe auxiliary power is normal. ple, CV-WIRE, PIPE, CC-STICK.) 2. Make sure the electrode (wire, gas, voltage, current etc.
f-1 DIaGRaMs RaNGeR® 305D (Ce) f-1
f-2 DIaGRaMs RaNGeR® 305D (Ce) f-2
RaNGeR® 305D (Ce) + _ ELECTRODE CABLE TO WIRE FEED UNIT K1819-10 CONTROL CABLE TO LN-742 INPUT CABLE PLUG TO WORK Keep guards in place. Keep away from moving parts. Only qualified personnel should install,use or service this equipment. MOVING PARTS can injure N.A. WELDING CABLES MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE APPLICATIONS. SEE OPERATING MANUAL. N.B. CONNECT WELDING CABLES TO OUTPUT STUDS FOR DESIRED POLARITY.
DIaGRaMs f-4 9/03 2 f-4 RaNGeR® 305D (Ce)
f-5 DIaGRaMs RaNGeR® 305D (Ce) f-5
DIaGRaMs RaNGeR® 305D (Ce) NOte: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement. Give the equipment code number.
F-7 RANGER® 305D NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement. Give the equipment code number.
DIaGRaMs RaNGeR® 305D (Ce) NOte: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement. Give the equipment code number.
60.00 1524.0 CENTER OF GRAVITY 59.20 1503.7 60.21 1529.3 29.67 753.6 29.63 752.6 26.52 673.6 17.50 444.5 17.00 431.8 19.50 495.3 21.06 534.9 21.50 546.1 6.33 160.9 11.03 280.2 29.83 757.6 A 35.08 891.03 DIMeNsION PRINt RaNGeR® 305D (Ce) M21086 34.24 869.
Index of Sub Assemblies - 12486 KEY PART NUMBER DESCRIPTION QTY Index of Sub Assemblies AR 1 P-939-C Case Front Assembly AR 2 P-939-D Control Panel Assembly AR 3 P-939-E Stator Rotor Assembly AR 4 P-939-F Blower Baffle Assembly AR 5 P-939-G Base Fuel Tank Battery Assembly AR 6 P-939-H Engine Assembly AR 7 P-939-J Covers & Case Back Assembly AR Printed 12/01/2015 at 15:04:48. Produced by Enigma.
Printed 12/01/2015 at 15:04:48. Produced by Enigma. Index of Sub Assemblies - 12486 P-939-A.
Case Front Assembly KEY DESCRIPTION QTY 1 9SG3860-6 CASE FRONT 1 2 9ST14166-9 OUTPUT TERMINAL KIT 2 3A 9SM20194-2 CIRCUIT BREAKER 1 3B 9SS25593 MOUNTING BRACKET 1 9SS25592 MOUNTING PLATE 1 9SS9225-63 THREAD FORMING SCREW (CUTTING) 2 9SE106A-1 LOCKWASHER 3 9SCF000010 #10-24HN 6 4 9SS24911-1 PLASTIC COVER 1 5 9SM20193 RESIDUAL CURRENT DEVICE 1 6 9SM20152-4 PLUG OUTLET 1 7 9SM20152-3 RECEPTACLE-230V 1 8 9SM20152-2 RECEPTACLE-115V 1 9 9ST9187-1 1/4-20HJLN 1
Case Front Assembly KEY PART NUMBER DESCRIPTION QTY 9SE106A-1 LOCKWASHER 3 9ST9695-1 LOCKWASHER 3 28 9SG6435-2 Rating Plate 1 29 9SS9225-68 THREAD FORMING SCREW (CUTTING) 4 31 9SM20007 OUTPUT STUD COVER 2 9SS25669 OUTPUT STUD COVER PLATE 2 9SS9225-66 SELF TAPPING SCREW 4 Printed 12/01/2015 at 15:04:48. Produced by Enigma.
Printed 12/01/2015 at 15:04:48. Produced by Enigma. Case Front Assembly P-939-C.
Control Panel Assembly 2A DESCRIPTION QTY 9SG3593 TOP BEZEL 1 9SS24738-1 SCREWS FOR THERMOPLASTICS 2 9SG3594-1 RIGHT BEZEL 1 9SS24738-1 SCREWS FOR THERMOPLASTICS 2 9SG3594-2 LEFT BEZEL 1 9SS24738-1 SCREWS FOR THERMOPLASTICS 2 5 9SS13146-4 SWITCH-PUSH BUTTON 1 6 9SS13146-1 START BUTTON 1 7 9SS17475-3 HOURMETER 1 12 9ST10491-1 KNOB 1 9ST13483-7 O RING 011 2 9SM19685-4 CONNECTOR & LEAD ASBLY 1 14A 9ST10812-112 POTENTIOMETER-ST 2 14B 9SS18280 POTENTIOMETER SPACER
Control Panel Assembly PART NUMBER DESCRIPTION QTY 9SS24630 METER HOUSING SEAL 2 9SM19368 METER BEZEL 2 9ST14807-9 FILTER LENS 2 9SCF000389 #4-40X.375SS-PPNHS-FULL-GR2-3147 4 9SCF000005 #6-32HN 4 9SS9262-3 PLAIN WASHER 4 Printed 12/01/2015 at 15:04:48. Produced by Enigma.
Printed 12/01/2015 at 15:04:48. Produced by Enigma. Control Panel Assembly P-939-D.
Stator Rotor Assembly Printed 12/01/2015 at 15:04:48. Produced by Enigma. KEY PART NUMBER DESCRIPTION QTY 1A 9SG3930-3 STATOR FRAME ASBLY 1 1B 9SCF000105 3/8-16X1.25HHCS 8 2B 9SE106A-16 LOCKWASHER 2 2A 9SS9262-120 PLAIN WASHER 2 2B 9SE106A-16 LOCKWASHER 2 2C 9SCF000067 3/8-16HN 2 4A 9SS17895 DISC CLAMPING BAR 6 4B 9ST8833-47 5/16-18 X .
Printed 12/01/2015 at 15:04:48. Produced by Enigma. Stator Rotor Assembly P-939-E.
Blower Baffle Assembly KEY DESCRIPTION QTY 9SG4097-10 Blower Baffle Assembly 1 1 9SG3862-1 BAFFLE 1 2 9ST13086-163 WARNING DECAL 1 3 9SS24624 BAFFLE 1 11B 9SS22168 HEAT SINK HOLDER 2 9SS9225-17 THREAD FORMING SCREW (ROLLING) 2 9SS9225-17 THREAD FORMING SCREW (ROLLING) 2 11D 9SS9262-98 PLAIN WASHER 2 11E 9SE106A-2 LOCKWASHER 2 11F 9SCF000017 1/4-20HN 2 7A 9SG5507-3 WELD CONTROL PC BD ASBLY 1 9SS8025-100 SELF TAPPING SCREW 4 9SL11845-1 CHOPPER HEATSINK ASBLY 1
Blower Baffle Assembly KEY 14A 16 18A DESCRIPTION QTY 9SL11768-1 PULL COIL/BATTERY PC BD ASBLY 1 9SS8025-100 SELF TAPPING SCREW 4 9SS9225-76 SELF TAPPING SCREW 1 9SS9262-27 PLAIN WASHER 1 9SCF000010 #10-24HN 1 9SE106A-1 LOCKWASHER 1 9ST9695-1 LOCKWASHER 1 9SS18543-5 GROMMET 1 9SS9225-68 THREAD FORMING SCREW (CUTTING) 1 9SS10404-132 RESISTORWW25W105% 1 9SCF000009 #10-24X3.
Printed 12/01/2015 at 15:04:48. Produced by Enigma. Blower Baffle Assembly P-939-F.
Base, Fuel Tank, Battery Assembly 1 DESCRIPTION QTY 9SG3925-1 BASE 1 9SL12164-2 FUEL TANK ASBLY 1 2A 9SG4457-2 Fuel Tank 1 2C 9SM20302 FUEL SENDER 1 2D 9SS19565-4 FUEL FITTING ASBLY 1 2E 9SS19563 RUBBER PLUG 2 2F 9SS20541 FUEL CAP 1 2G 9SS19564 FUEL FITTING 1 9SL11135-3 RECTIFIERCHOKESTATOR SUPPORT ASBLY 1 3A 9SL11010 STATOR SUPPORT 1 3B 9SM19416 CHOKE ASBLY 1 3C 9SCF000187 5/16-18X2.
Base, Fuel Tank, Battery Assembly KEY PART NUMBER DESCRIPTION QTY 9B 9SS10888-35 HOSE CLAMP 1 9A 9ST10642-91 FLUX TUBE 1 9B 9SS10888-35 HOSE CLAMP 1 9C 9ST13777-5 HOSE CLAMP 1 10A 9SL11643 ENGINE SUPPORT 1 9SS9225-68 THREAD FORMING SCREW (CUTTING) 4 9SM19770 BATTERY ACCESS DOOR 1 9SS9225-68 THREAD FORMING SCREW (CUTTING) 4 9SM15045-78 Acoustical Foam 1 12 9SS9225-68 THREAD FORMING SCREW (CUTTING) 4 13 9SS17851 DECAL-CAUTION 1 14 9SL12922 DECAL CARRIER 1 12 11A
Printed 12/01/2015 at 15:04:48. Produced by Enigma. Base, Fuel Tank, Battery Assembly P-939-G.
Engine Assembly Printed 12/01/2015 at 15:04:48. Produced by Enigma. KEY PART NUMBER DESCRIPTION QTY 1A 9SM21505 Engine 1 1B 9SS25211 FAN COUPLING HUB 1 9E 9SE106A-14 LOCKWASHER 2 1D 9ST14731-11 METRIC HEX HD SCREW-M8 X1.25 3 11C 9SE106A-2 LOCKWASHER 1 11B 9SCF000014 1/4-20X.
Engine Assembly 18 PART NUMBER DESCRIPTION QTY 9B 9SS25230 AIR FILTER MOUNTING BAND 1 9C 9SCF000062 5/16-18X1.00HHCS 2 9D 9SS9262-121 PLAIN WASHER 2 9E 9SE106A-14 LOCKWASHER 2 9F 9SCF000029 5/16-18HN 2 9G 9SM20061 AIR INTAKE HOSE 1 9H 9SS10888-29 HOSE CLAMP 2 10A 9SS20140-3 SOLENOID ASBLY 1 11B 9SCF000014 1/4-20X.
Printed 12/01/2015 at 15:04:48. Produced by Enigma. Engine Assembly P-939-H.
Covers & Case Back Assembly DESCRIPTION QTY 1A 9SG4405-13 ROOF ASBLY 1 2B 9SS24739-27 1/4X.75 TEK SCREW 3 9SL12922 DECAL CARRIER 1 2A 9SG4405-9 RIGHT CASE SIDE ASBLY 1 2B 9SS24739-27 1/4X.
Covers & Case Back Assembly KEY PART NUMBER DESCRIPTION QTY 22D 9SS10888-16 HOSE CLAMP 2 22C 9SM20064 UPPER RADIATOR HOSE 1 22D 9SS10888-16 HOSE CLAMP 2 22E 9SS25524 HOSE FITTING 1 22G 9ST10642-218 FLEX HOSE 1 22H 9SS10888-35 HOSE CLAMP 2 23A 9SG4405-10 LEFT CASE SIDE ASBLY 1 26A 9SG4405-12 LEFT ENGINE COVER ASBLY 1 27A 9SG4405-11 RIGHT ENGINE COVER ASBLY 1 29 9SL12037 DECAL CARRIER 1 30 9SM15045-40 ACOUSTICAL FOAM 1 9SS25514 COOLANT BOTTLE BRACKET 1 9SS922
Printed 12/01/2015 at 15:04:48. Produced by Enigma. Covers & Case Back Assembly P-939-J.
WARNING AVISO DE PRECAuCION Spanish l Do not touch electrically live parts or l No toque las partes o los electrodos bajo carga con la piel o ropa mojada. l Aislese del trabajo y de la tierra. French l Ne laissez ni la peau ni des vête- German l Berühren Sie keine stromführenden ATTENTION WARNuNG Portuguese ATENÇÃO Japanese l Keep flammable materials away. l Wear eye, ear and body protection.
l Keep your head out of fumes. l Use ventilation or exhaust to l Turn power off before servicing. l Do not operate with panel open or guards off. remove fumes from breathing zone. l Los humos fuera de la zona de res- piración. l Mantenga la cabeza fuera de los humos. Utilice ventilación o aspiración para gases. l Gardez la tête à l’écart des fumées. l Utilisez un ventilateur ou un aspira- l Desconectar el cable de ali- mentación de poder de la máquina antes de iniciar cualquier servicio.
Customer assistanCe PoliCy The business of The Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equipment. Our challenge is to meet the needs of our customers and to exceed their expectations. On occasion, purchasers may ask Lincoln Electric for advice or information about their use of our products. We respond to our customers based on the best information in our possession at that time.
