Contents Before driving Introduction 2 Instrumentation 3 Controls and features 26 Seating and safety restraints 71 Starting and driving Starting 90 Driving 95 Roadside emergencies 109 Servicing Maintenance and care 126 Capacities and specifications 160 Reporting safety defects 166 Index 167 All rights reserved.
Introduction ICONS Indicates a warning. Read the following section on Warnings for a full explanation. Indicates vehicle information related to recycling and other environmental concerns will follow. Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment. WARNINGS Warnings provide information which may reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment.
Instrumentation 3
Instrumentation Instrument cluster (pg. 6) Headlamp control (pg. 26) Turn signal and wiper/washer control (pg. 35) 4 — M NO R P 60 6 ABS 7 40 C 80 100 60 20 2 E km/h 80 120 40 140 160 20 FILL ON RIGHT SERVICE ENGINE SOON 0 AIR BAG 200 0 RPMx1000 0 MPH BRAKE HI LO OFF 0FF LIGHTS AUTO LAMP P RESUME SET ACCEL COAST OFF Auto lamp (pg. 27) 4 ON Instrument panel dimmer switch (pg. 27) 100 180 1 H ! 5 3 F TURN ON HEAD LAMPS T/C OFF + SRS Speed control (pg.
Instrumentation Electronic sound system control (pg. 35) Electronic sound system; refer to Audio Guide (pg. 33) Clock (pg. 33) Message Center (pg. 12) SYSTEM DRIVER ID SELECT L C E A O VEHICLE HANDLING DISPLAY I MENU T N TRIP N T RESET DTE ECON N 000000.
Instrumentation WARNING LIGHTS AND CHIMES 4 – NO RM P 60 6 ABS 7 40 60 20 2 E C 80 100 km/h 80 120 40 140 160 20 100 180 1 H ! 5 3 F TURN ON HEAD LAMPS T/C OFF + FILL ON RIGHT SERVICE ENGINE SOON 0 AIR BAG 200 0 RPMx1000 0 MPH 120 000000.0 BRAKE Service engine soon Your vehicle is equipped with a SERVICE computer that monitors the engine’s ENGINE emission control system. This SOON system is commonly known as the On Board Diagnostics System (OBD II).
Instrumentation These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel and/or properly installing and securely tightening the gas cap. After three driving cycles without these or any other temporary malfunctions present, the Service Engine Soon light should turn off. (A driving cycle consists of a cold engine startup followed by mixed city/highway driving.) No additional vehicle service is required.
Instrumentation Anti-lock brake system (ABS) Momentarily illuminates when the ignition is turned to the ON position and the engine is off. If the light remains on, continues to flash or fails to illuminate, have the system serviced immediately. ABS Turn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the indicators stay on continuously or flash faster, check for a burned-out turn signal bulb.
Instrumentation Engine oil pressure Illuminates when the oil pressure falls below the normal range. Stop the vehicle as soon as safely possible and switch off the engine immediately. Check the oil level and add oil if needed. Refer to Engine oil in the Maintenance and Care chapter. This lamp also illuminates when the ignition is turned to ON and the engine is off. Traction ControlY off light Illuminates when the Traction Controly system has been disabled (by the driver or as a result of a system failure).
Instrumentation GAUGES – NO RM P 60 6 ABS 7 40 60 20 2 E C 80 100 km/h 80 120 40 140 100 160 20 180 1 H ! 5 3 F TURN ON HEAD LAMPS T/C OFF 4 + FILL ON RIGHT SERVICE ENGINE SOON 0 AIR BAG 200 0 RPMx1000 0 MPH 120 000000.0 BRAKE Fuel gauge Displays approximately how much F fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion.
Instrumentation Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer in the red zone may damage the engine. 4 5 6 ABS 7 3 2 ANTI THEFT 1 0 RPMx1000 H NO RM Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating.
Instrumentation ELECTRONIC MESSAGE CENTER The electronic message center only SYSTEM works when the ignition is in the ON position. E/M The message center tells you about the condition of your vehicle by two methods: MENU SELECT • operator selectable features VEHICLE HANDLING • continuous warning reporting of monitored systems TRIP DISPLAY You can select different features for the message center to display by DTE ECON RESET using the message center controls located to the right of the instrument cluster.
Instrumentation System check Pressing this control causes the SYSTEM message center to cycle through a status of each of the systems being monitored. For each of the monitored systems, the message center will indicate either an OK message or a warning message for three seconds. The sequence of the system check report is as follows: • voltage level • engine temperature • oil level • engine coolant level • washer fluid level • doors closed (driver and passenger side).
Instrumentation Door Ajar Driver’s Door Ajar Check Engine Temp Transmission Overheat Check Transmission Low Oil Level Check Charging System Low Fuel Level Low Engine Coolant Low Tire Pressure (if equipped) Gear Display Data ERR Brake Lamp Out Check Traction Control Check Ride Control Trunk Ajar Check Steering Assist Low Washer Fluid Air Leveling Disabled Tail Lamp Out Check FRT Turn Lamps Turn on Headlamps Cannot be reset Warning returns after 10 minutes Warning reappears after key is turned from OFF to O
Instrumentation DTE/ECON • Press the DTE/ECON control DTE ECON once to display the approximately how far you can drive before running out of fuel, or the distance to empty (DTE). To ensure accuracy, turn the ignition OFF when you fill the tank. • Press the DTE/ECON control a second time to display the average fuel economy in liters/100 kilometers or miles/gallon, based on distance traveled and rate of fuel used information.
Instrumentation RESET Press this control to reset: RESET • warnings • average fuel economy • trip odometers The other selectable features are unaffected by pressing RESET. DISPLAY Press this control to turn the message center display off. Press it again to turn the display on. Warnings override an off display and must be reset for the display to be off again. DISPLAY VEHICLE HANDLING Press this control once to adjust VEHICLE HANDLING RIDE CONTROL SETTINGS (if equipped) between NORMAL, PLUSH and FIRM.
Instrumentation Traction control Refer to Traction Controly for more information. Express window • Standard vehicle setting is saved as vehicle setting only (not the Driver 1 or 2 individualized profiles). • Standard vehicle with Memory Profile System: setting may be saved to either Driver 1 or 2 personalized profiles or as a vehicle setting. • Settings: ON or OFF. • Original setting: ON. • Setting adjustment is made using the message center MENU/SELECT controls.
Instrumentation • Standard vehicle with Memory Profile System: setting may be saved to either the Driver 1 or 2 personalized profiles or as a vehicle setting. • Settings: ON or OFF. • Original setting: ON. • Setting adjustment is made using the message center MENU/SELECT controls. Reverse mirrors • Standard vehicle: setting is saved as vehicle setting only (not the Driver 1 or 2 individualized profiles).
Instrumentation Autolamp on/delay time Standard vehicle with Memory Profile System: setting may be saved to either the Driver 1 or 2 personalized profiles or as a vehicle setting. Instrument panel dim control setting • Standard vehicle: setting is saved as vehicle setting only (not the Driver 1 or 2 individualized profiles). • Standard vehicle with Memory Profile System: setting may be saved to either the Driver 1 or 2 personalized profiles or as a vehicle setting. • Settings: variable.
Instrumentation settings (not individualized settings). To change a feature setting see Driver profile features in this section. Associated systems Keyless Entry System Programming personalized codes: With a key and/or Key FOB outside of the vehicle: • Enter the factory code • Press the 1/2 control • Enter the five digit personalized code Press: • The 1/2 control to save the code as Driver 1. • The 3/4 control to save the code as Driver 2.
Instrumentation Driver profile features Express window • Standard vehicle-setting is saved as vehicle setting only (not the DRIVER MEMORY 1 or 2 individualized profiles). • Standard vehicle with Memory Profile System-setting may be saved to either the DRIVER MEMORY 1 or 2 personalized profiles or as a vehicle setting.
Instrumentation Easy entry/exit seat access • Standard vehicle-setting is saved as vehicle setting only (not the DRIVER MEMORY 1 or 2 individualized profiles). • Standard vehicle with Memory Profile System-setting may be saved to either the DRIVER MEMORY 1 or 2 personalized profiles or as a vehicle setting.
Instrumentation • Standard vehicle with Memory Profile System-setting may be saved to either the DRIVER MEMORY 1 or 2 personalized profiles or as a vehicle setting. • Settings-low, normal, high • Original setting-normal • Setting adjustment made using: Message Center-VEHICLE HANDLING/SELECT controls Autolamp on/delay time • Standard vehicle with Memory Profile System-setting may be saved to either the DRIVER MEMORY 1 or 2 personalized profiles or as a vehicle setting.
Instrumentation • Standard vehicle with Memory Profile System-setting may be saved to either the DRIVER MEMORY 1 or 2 personalized profiles or as a vehicle setting. • Settings-horizontal and vertical • Original setting-N/A • Setting adjustment made using: outside mirror control Basic operation In order for the system to be able to store or recall an individuals seat or mirror position preferences, the Driver Profile System must first recognize who will be driving the vehicle.
Instrumentation Memory Profile System (if equipped) The Memory Profile System allows the two primary drivers to select and save individualized preferences for the following eleven vehicle features: • Express window • Auto door locks • Horn chirp • Easy entry/exit seat access • Reverse mirrors • Adjustable ride • Adjustable steering • Autolamp on/delay time • Instrument panel dim control • Driver’s seat position • Outside mirror position Basic Operation of the Driver Profile System with Memory Profile System
Controls and features HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps only. Rotate to the second position to also turn on the headlamps. OFF P Daytime running lamps (DRL) (if equipped) Turns the highbeam headlamps on with a reduced output. To activate: • the engine must be running • the headlamp control is in the OFF or Parking lamps position. The Daytime Running Light (DRL) system will not illuminate the tail lamps and parking lamps.
Controls and features INSTRUMENT PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlight and parklamp operation. • Push up to brighten. • Push down to dim. PANEL DIM AUTOLAMP CONTROL The autolamp system provides light AUTO sensitive automatic on-off control of LAMP the exterior lights normally controlled by the headlamp control. The autolamp system also keeps the MAX lights on for a preselected period of OFF time after the ignition switch is turned to OFF.
Controls and features Turning the EATC off Press OFF. The Outside Temperature (EXT) function will continue to operate until the ignition is turned off. EXT OFF AUTO MAX A/C Automatic operation Press AUTO and select the desired temperature. The selected temperature and the word AUTO will appear in the display window. The EATC system will either heat or cool to achieve the selected temperature.
Controls and features To control the temperature, select any temperature between 18°C (65°F) and 29°C (85°F) by pressing the temperature control. FRONT REAR For continuous maximum cooling, push the temperature control until 16°C (60°F) is shown in the display window. The EATC will continue maximum cooling (disregarding the displayed temperature) until a warmer temperature is selected by pressing the temperature control.
Controls and features steering wheel control up for higher fan speed or down for lower fan speed. The display will show and a bar ˚F graph to indicate manual fan operation and relative speed. AUTO To return to automatic fan operation, press AUTO. Manual override controls The override controls allow you to determine where airflow is directed. To return to full automatic control, press AUTO. ˚F AUTO EXT OFF AUTO FRONT REAR MAX A/C and The air conditioning compressor will operate in all modes except .
Controls and features • • • • provided in this mode. The air will be heated or cooled based on the temperature selection. For added customer comfort, the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers. -Allows for maximum heating by distributing outside air through the floor ducts. However, the air cannot be cooled below the outside temperature because the air conditioning does not operate in this mode.
Controls and features changed, then the outside temperature will return to the window along with the override selection. The outside temperature reading is most accurate when the vehicle is moving. Higher readings may be obtained when the vehicle is not moving. The readings that you get may not agree with temperatures given on the radio due to differences in vehicle and station locations. Operating tips • In humid weather, select FRONT before driving. This will prevent your windshield from fogging.
Controls and features The rear defroster control is located on the instrument panel. Press the defroster control to clear the rear window of thin ice and fog. • The small LED will illuminate when the defroster is activated. FRONT REAR The ignition must be in the ON position to operate the rear window defroster. The defroster turns off automatically after 10 minutes or when the ignition is turned to the OFF position.
Controls and features POSITIONS OF THE IGNITION 1. ACCESSORY, allows the electrical 4 accessories such as the radio to 3 operate while the engine is not 5 running. 2. LOCK, locks the steering wheel, 2 automatic transmission gearshift lever and allows key removal. 1 3. OFF, shuts off the engine and all accessories without locking the steering wheel. 4. ON, all electrical circuits operational. Warning lights illuminated. Key position when driving. 5. START, cranks the engine.
Controls and features TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. HI LO OFF Cornering lamps (if equipped) When the turn signal is used when the headlamps are on, the cornering lamps will light either the right or left side depending on the direction of the turn. The flash rate of the turn signal will speed up considerably if the Lighting Control Module detects a left or right turn lamp bulb (front or rear) is burned out.
Controls and features Speed sensitive volume The recommended level for speed sensitive volume is from level 1 through level 3. Level 0 turns the speed sensitive volume off and Level 7 is the maximum setting for the speed sensitive volume. Climate control features • Press TEMP up or down to adjust temperature. • Press FAN up or down to adjust fan speed. SPEED CONTROL To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or ON above 48 km/h (30 mph).
Controls and features To turn speed control off • Press OFF or • Turn off the vehicle ignition. ON OFF Once speed control is switched off, the previously programmed set speed will be erased. When the OFF control is pressed, the message “SPEED CONTROL OFF” will appear for 5 seconds in your message center. To set a speed • Press SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph).
Controls and features Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. To set a higher set speed • Press and hold SET ACC/SET ACCEL. Release the control when RES the desired vehicle speed is SET reached or ACCEL • Press and release SET ACC/SET COAST ACCEL. Each press will increase the set speed by 1.6 km/h (1 mph) if (E) English is selected or 2 km/h (1.25mph) if (M) Metric is selected in the Message Center.
Controls and features • Depress the brake pedal. When the desired vehicle speed is reached, press SET ACC/SET ACCEL. When the COAST or SET ACCEL control is pressed and released, the message “SPEED CONTROL SET” will appear for 5 seconds in your message center. RES SET ACCEL COAST To disengage speed control • Depress the brake pedal. When the brake pedal is depressed, the message “SPEED CONTROL CANCELED” will appear for 5 seconds in your message center.
Controls and features TILT STEERING Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control. Never adjust the steering wheel when the vehicle is moving. INTERIOR LAMPS Map lamps To turn on the map lamps, press the control next to each lamp. If equipped with a moon roof, the map lamps are located on the rearview mirror. Press the control next to the map lamp to illuminate the lamp.
Controls and features Rear courtesy/reading lamps The courtesy lamp lights when: • any door is opened. • when the instrument panel dimmer switch is turned to the courtesy lamp position. • if any of the keyless entry keypad controls are pressed and the ignition is OFF. With the ignition key in the ACC or ON position, the reading lamp can be turned on by pressing the rocker control. LINCOLN RESCU SYSTEM (IF EQUIPPED) Lincoln RESCU runs a self-test when you start your vehicle.
Controls and features 1. By pressing the Information control. i INFO 2. By pressing the Emergency (S.O.S) control. S.O.S. 3. The system will automatically activate if the vehicle’s air bags have been deployed. Quick summary • To utilize your vehicle’s RESCU system, your cellular phone must be activated. • Information or emergency assistance can be requested whenever your key is in the RUN/START position and for six minutes after the vehicle is turned off.
Controls and features • Typically, voice communication with an operator is established within one minute after an assistance control is pressed. • The operator verbally obtains details of your situation and, if necessary, ties your vehicle into a three-way phone call with the United States Auto Club or local 911 or other emergency services to dispatch the appropriate assistance to your location.
Controls and features • Last recorded speed and direction of the vehicle • Time tag identifying when last position was taken • Call-back phone number After the transmission is complete, the call is forwarded to an operator who will verify the details of the request and confirm the vehicle’s location using a computerized map.
Controls and features Activation and deactivation When either of the two Lincoln RESCU controls are pressed, or the air bags are deployed (this will activate the system as an emergency automatically), a warning light, located in the overhead console, will begin to flash and status messages will be displayed on the vehicle’s message center, confirming an assistance request has been made. The warning light will continue to flash throughout the activation.
Controls and features • INFORMATION REQUEST, EMERGENCY REQUEST or AIR BAG REQUEST • CALL IN PROGRESS • RINGING RESPONSE CENTER • SENDING LOCATION DATA • DATA RECEIVED • WAITING FOR OPERATOR Once an assistance request is made, it will typically take less than one minute until contact is made with an operator.
Controls and features Similarly, if the cellular call is disconnected by the network prior to receipt of the termination tone, another call to the response center will also automatically be dialed. The message “REDIAL IN PROGRESS” will be displayed on the message center and voice communication with an operator will be restored. During redial calls, full control of the cellular phone is returned to you.
Controls and features Lincoln RESCU system limitations Inoperative if cellular phone inactive or inoperative Lincoln RESCU utilizes your vehicle’s cellular phone and will not operate if cellular service has not been activated or if the phone is inoperative. Inoperative if battery discharged or disconnected Lincoln RESCU is powered by the vehicle’s battery and will not operate if the battery if discharged or disconnected.
Controls and features Inoperative if cellular signal marginal or unavailable Since the Lincoln RESCU System utilizes the vehicle’s cellular phone, it can only be operated in geographical areas with cellular coverage. Although approximately 90 percent of the U.S. population lives and works in cellular coverage areas, there are various rural or mountainous areas where coverage is marginal or does not exist.
Controls and features features and must be avoided. Operation is possible with no incoming calls, call forwarding, busy/no answer transfer and call waiting, but these features could impact overall system performance. Because carriers are regularly making new features available to customers, this list may not be complete. Contact you dealer for assistance if you are unsure if a particular cellular feature is compatible with your Lincoln RESCU System.
Controls and features Optional password selection/false activations At the time of your registration, you will be given the option of establishing a user password. All aspects of your service will be identical regardless of your password decision except the way false emergency activations are handled. If established, the password will be requested by the operator to confirm an emergency activation was initialed in error.
Controls and features Security Response Center. After your initial service period expires, you may be requires to pay a monitoring service fee. Your dealer can provide you with specific information regarding post-initial service period fees. Relinquishing your vehicle At the time you relinquish your vehicle, it is important that you contact the Lincoln Security Response Center at 1–800–223–1327 and cancel your security service.
Controls and features and gates, and can also control home or office lighting and security systems (with the available accessory package). When programming your HomeLinkt Universal Transmitter, you will be operating the garage door or gate. Be sure that people and objects are out to the way to prevent potential harm or damage. Do not use the HomeLinkt Universal Transmitter with any garage door opener that lacks safety stop and reverse features as required by U.S.
Controls and features If you do not successfully program the HomeLinkt Universal Transmitter after repeated attempts, refer to Training a rolling code which follows or call toll-free customer assistance: 1–800–355–3515. Note to Canadian residents During programming, your hand-held transmitter may automatically stop transmitting after two seconds which may not be long enough to program the HomeLinkt Universal Transmitter.
Controls and features 1. Locate the training control on the garage door opener receiver. Refer to the garage door opener manual or call 1–800–355–3515 if there is difficulty locating the training control. 2. Press the training control on the garage door opener receiver until the training light (next to the control) begins to flash (1-2 seconds). 3. Press the programmed HomeLinkt control in the vehicle until the training light on the garage door receiver turns solid (1-2 seconds).
Controls and features calibration may be necessary. Refer to Compass calibration adjustment. Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. This variation is four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error. Refer to Compass zone adjustment. Compass zone adjustment 1.
Controls and features 5. Release the switch, then slowly press it down again. Press the switch repeatedly until the correct zone setting for your geographic location is displayed on the upper right corner of the mirror. 6. To exit the zone setting mode, release pressure from the switch for greater than two seconds. Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines.
Controls and features Press the control to turn the mirror on or off. The mirror will automatically return to the normal state whenever the vehicle is placed in R (reverse)(when the mirror is on) to ensure a bright clear view when backing up. Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products. On vehicles equipped with a moonroof, the automatic rear view mirror has two map lamps. Refer to Interior lights for more information.
Controls and features POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to open. WINDOW LOCK • Pull the top portion of the rocker switch to close. Express down To make the driver window open fully without holding the window control, press the driver window control completely down and release quickly. Depress again to stop window operation.
Controls and features Window lock The window lock feature allows only the driver to operate the power WINDOW windows. LOCK To lock out all the window controls except for the driver’s press the right side of the control. Press the left side to restore the window controls. Accessory delay With accessory delay, the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until any door is opened.
Controls and features 3. Return to the center position to lock mirrors in place. Heated outside mirrors Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors. CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside.
Controls and features CENTER CONSOLE (IF EQUIPPED) Your vehicle is equipped with a variety of console features. These include: • utility compartment • cupholders • ashtray and lighter • compact disc changer (if equipped) • power point • cellular phone (if equipped) Use only soft cups in the cupholder. Hard objects can injure you in a collision. Compact disc changer (if equipped) The compact disc changer is located inside the front center console.
Controls and features POSITIVE RETENTION FLOOR MAT Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. To remove the floor mat, reverse the installation procedure. PERIMETER ALARM SYSTEM (IF EQUIPPED) Arming the system When armed, this system will help protect your vehicle from unauthorized entry.
Controls and features If a door is open, the system is prearmed and is waiting for the door to close. The anti-theft indicator on the instrument panel will be lit continuously when the system is prearmed. Once the doors are closed, the system will arm in 30 seconds. Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by using your remote entry transmitter. • Unlock the doors by using your keyless entry keypad. • Unlock the doors with a key.
Controls and features If one or both of your SecuriLocky keys are lost or stolen and you want to ensure the lost or stolen key will not operate your vehicle, bring your vehicle and all available SecuriLocky keys to your dealership for reinitialization. REMOTE ENTRY SYSTEM The remote entry system allows you to lock or unlock all vehicle doors without a key. The remote entry features only operate with the ignition in the OFF position. Unlocking the doors Press this control to unlock the driver door.
Controls and features Opening the trunk Press the control once to open the trunk. Be certain the trunk is closed before driving your vehicle. The trunk may appear closed, but it may not be latched. Failure to do so may cause objects to fall out of the trunk or block rear view vision. Sounding a panic alarm Press this control to activate the alarm. To deactivate the alarm, press the control again or turn the ignition to ACC or ON.
Controls and features • structures around the vehicle • other vehicles parked next to the vehicle To replace the battery: 1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. 2. Place the positive (+) side of new battery in the same orientation. Refer to the diagram inside the transmitter unit. 3. Snap the two halves back together.
Controls and features The inside lights will not turn off if: • they have been turned on with the dimmer control or • any door is open. The battery saver will shut off the interior lamps 40 minutes after the ignition has been turned to the OFF position. KEYLESS ENTRY SYSTEM With the keyless entry keypad, you can: • lock or unlock the vehicle doors without using the key. • arm and disarm the perimeter alarm system (if equipped). • reprogram remote entry transmitters.
Controls and features • 3/4 recalls personality 2 • 9/0 does not recall a personality All of the vehicle doors will lock and unlock to confirm programming of the new code. Each personality driver profile (personality 1 or personality 2) can be associated with only one personal code. The factory-set code cannot be associated with a personality profile. Do not set a code that includes five of the same number or presents them in sequential order. Thieves can easily figure out these types of codes.
Controls and features After the factory-set code or personal code has been entered, you can unlock all doors (press 3/4) and release the trunk (press 5/6) as long as the controls are pressed within 5 seconds of each other. Locking doors with the keyless entry system It is not necessary to enter the factory-set code prior to locking all doors. To lock the doors: 1. Press 7/8 and 9/0 at the same time.
Seating and safety restraints SEATING Head restraints Push or pull the head rests to the desired position. Adjusting the power front seats – door mounted controls The controls for the power seats are located on the inside of each front door. Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Seating and safety restraints Press to move the seat forward or backward. Press to move the front portion of the seat cushion up or down. Press to move the rear portion of the seat cushion up or down.
Seating and safety restraints Heated seats (if equipped) To operate the heated seats: • Slide the control to BACK to heat the seatback only. • Slide the control to BOTH to heat the seatback and the seat cushion. FRONT REAR EXT OFF AUTO MAX A/C HI BACK BACK BOTH BOTH HEATED • Rotate the thumbwheel to select the desired heat (from 0 (OFF) to 5 (HI)). Allow five minutes for the heat level to stabilize.
Seating and safety restraints Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver, should always wear their safety belts. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Seating and safety restraints 2. To unfasten, push the red release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front and rear seat passenger outboard safety belts have two types of locking modes described below: Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement.
Seating and safety restraints How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
Seating and safety restraints Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button and slide the height control down. To raise the height of the shoulder belt, slide the height adjuster up. Pull down on the height adjustment assembly to make sure it is locked in place.
Seating and safety restraints Insert the tongue into the correct buckle. To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. To tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips. Shorten and fasten the belt when not in use.
Seating and safety restraints Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON position... Then... The safety belt warning light illuminates for one to two minutes and the warning chime sounds for four to eight seconds.
Seating and safety restraints AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) km/h 80 120 SYSTEM 140 160 DRIVER ID 100 SELECT MENU SERVICE ENGINE SOON 0 180 200 0 RPMx1000 0 MPH TRIP 120 L C A VEHICLE HANDLING DISPLAY T AIR BAG RESET 000000.
Seating and safety restraints Do not place objects or mount equipment on or near the air bag cover on the steering wheel or in front seat areas that may come into contact with a deploying air bag. Failure to follow this instruction may increase the risk of personal injury in the event of a collision. Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer.
Seating and safety restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the air bag. Small amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic.
Seating and safety restraints section in the Instrumentation chapter. Routine maintenance of the air bag is not required. A difficulty with the system is indicated by one or more of the following: • The readiness light will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on. • A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and light are repaired.
Seating and safety restraints Children and safety belts Children who are too large for child safety seats (as specified by your child safety seat manufacturer) should always wear safety belts. Follow all the important safety restraint and air bag precautions that apply to adult passengers in your vehicle. If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child’s face or neck, the child should wear the lap and shoulder belt.
Seating and safety restraints When installing a child safety seat: • Use the correct safety belt buckle for that seating position. • Make sure the tongue is securely fastened in the buckle. • Keep the buckle release button pointing up and away from the safety seat, with the tongue between the child seat and the release button, to prevent accidental unbuckling. • Place seat back in upright position. • Put the safety belt in the automatic locking mode. Refer to Automatic locking mode.
Seating and safety restraints Air bag can kill or injure a child in a child seat. If you must use a forward-facing child seat in the front seat, move seat all the way back. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4.
Seating and safety restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8.
Seating and safety restraints Installing a child safety seat in the center seating position with adjustable lap belt 1. Lengthen the lap belt. To lengthen the belt, hold the tongue so that its bottom is perpendicular to the direction of webbing while sliding the tongue up the webbing. 2. Place the child safety seat in the center seating position. 3. Route the tongue and webbing through the child seat according to the child seat manufacturer’s instructions. 4.
Seating and safety restraints trim panel, which is behind the rear seat back. To use this anchorage, do the following: 1. Open the hinged cover located at the front of the high mount stop light. This cover conceals the tether strap anchor bracket. To prevent damage to the hinge, do not raise the hinged cover of the trim panel beyond its limit. 2. Install the tether strap bracket located directly below the cover.
Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use the accelerator when you have difficulty starting the engine. For more information on starting the vehicle, refer to Starting the engine in this chapter.
Starting 2. Make sure the headlamps and vehicle accessories are off. • Make sure the parking brake is set. BRAKE RELEASE HOOD • Make sure the gearshift is in P (Park). 3. Turn the key to 4 (ON) without turning the key to 5 (START).
Starting 4 – + T/C OFF NO RM P 7 40 60 20 2 E C 80 100 km/h 80 120 40 140 160 20 100 180 1 H ! 60 6 ABS 3 F TURN ON HEAD LAMPS 5 FILL ON RIGHT SERVICE ENGINE SOON 0 AIR BAG 200 0 RPMx1000 0 MPH 120 000000.0 BRAKE P R N D 3 1 Make sure the corresponding lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light ( ) will not illuminate. STARTING THE ENGINE 1.
Starting Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater-defroster system to respond quickly. Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below. For best results, plug the heater in at least three hours before starting the vehicle.
Starting Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air. Improve vehicle ventilation by keeping all air inlet vents clear of snow, leaves and other debris.
Driving BRAKES Your brakes are self-adjusting. Refer to the “Service Guide” for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Driving light will remain on and your vehicle should be serviced as soon as possible. Normal braking is still effective ! P unless the BRAKE warning lamp is also illuminated. BRAKE Using ABS • In an emergency or when maximum efficiency from the ABS is required, apply continuous full force on the brake.
Driving Your vehicle has an automatic parking brake release. To release the parking brake: 1. Turn the ignition to the RUN position. 2. Press the brake pedal. 3. Move the gearshifter from the P (Park) position to one of the forward gears (the parking brake will not release automatically when you shift into reverse). The brake pedal must remain pressed while the gearshifter is moved. If the parking brake fails to release after completing this procedure, use the manual parking brake release HOOD lever.
Driving sound coming from the engine compartment and the engine will not “rev-up” when you push further on the accelerator. This is normal system behavior. If you should become stuck in snow or on a very slippery road surface, try switching the Traction Controly system off. This may allow excess wheel spin to “dig” the vehicle out or enable a successful “rocking” maneuver. Refer to Message center in the Instrumentation chapter.
Driving The air suspension shut-off switch is located on the left side of the trunk. If this switch is in the OFF position, the rear air suspension will not operate. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. OFF Normal vehicle operation does not require any action by the driver.
Driving on the accelerator in each gear. Do not rock the vehicle for more than a few minutes, because it could damage the vehicle. Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn off the ignition whenever you leave your vehicle. Driving with a 4–speed automatic transaxle Your automatic overdrive transaxle provides fully automatic operation in either D (Overdrive) or 3 (Third).
Driving R (Reverse) With the gearshift in R (Reverse), the vehicle will move backward. You should always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift in the N (Neutral) position, the vehicle can be started and is free to roll. Hold the brake pedal down while in this position.
Driving D (Overdrive) The overdrive position is the normal driving position for an automatic overdrive transaxle. It works the same way as 3 (Third) but shifts to a fourth gear — an overdrive gear — when your vehicle cruises at a constant speed for any length of time. This fourth gear will increase your fuel economy when you travel at cruising speeds. Overdrive may not be appropriate for certain terrains.
Driving 1 (First) Use 1 (First) for when added engine braking is desired when descending steep hills. The automatic transaxle will shift to the proper gear to ascend any grade without any need to shift to 1 (First). Do not go faster than 61 km/h (38 mph) when in this gear. You can upshift from 1 (First) to overdrive at any time. When parking, do not use the gearshift in place of the parking brake. Always set the parking brake fully and make sure that the gearshift is securely latched in Park (P).
Driving VEHICLE LOADING Before loading a vehicle, familiarize yourself with the following terms: • Base Curb Weight: Weight of the vehicle including any standard equipment, fluids, lubricants, etc. It does not include passengers or aftermarket equipment. • Payload: Combined maximum allowable weight of cargo, passengers and optional equipment. The payload equals the gross vehicle weight rating minus base curb weight. • GVW (Gross Vehicle Weight): Base curb weight plus payload weight.
Driving Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label. Do not use replacement tires with lower weight capacities than the originals because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher weight limit than the originals do not increase the GVWR and GAWR limitations. TRAILER TOWING Your vehicle is classified as a light duty towing vehicle.
Driving Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label. Towing trailers beyond the maximum recommended gross trailer weight could result in engine damage, transmission/axle damage, structural damage, loss of control, and personal injury. Preparing to tow Use the proper equipment for towing a trailer, and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance.
Driving trailer’s lamps, see your Lincoln dealer. Be sure to follow their instructions carefully. If you do not install trailer lights correctly, you may cause damage to the vehicle’s lighting system or other vehicle systems. Driving while you tow Do not drive faster than 88 km/h (55 mph) when towing a trailer. Speed control may shut off if you are towing on long, steep grades. When towing a trailer: • Shift out of D (Overdrive) and into 3 (Third) or a lower gear when towing up or down steep hills.
Driving FUEL CONSUMPTION Fuel economy can be improved by avoiding: • lack of regular, scheduled maintenance. • excessive speed. • rapid acceleration. • extended idle. CHECKING YOUR HIGHWAY FUEL ECONOMY USING THE ELECTRONIC MESSAGE CENTER DISPLAY The following procedure will allow you to accurately monitor your actual highway fuel economy.
Roadside emergencies HAZARD FLASHER For information on the hazard flasher control, refer to Hazard lights control in the Roadside emergencies chapter. FUEL PUMP SHUT-OFF SWITCH If the engine cranks but does not start after a collision, the fuel pump shut-off switch may have been activated. The shut-off switch is a device intended to stop the electric fuel pump when your vehicle has been involved in a substantial jolt. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3.
Roadside emergencies Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color Fuse rating 5 amp 7.
Roadside emergencies 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 111
Roadside emergencies The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating 1 10A 2 10A 3 15A 4 10A 112 Description Lighting Control Module: Anti-Theft Indicator Lamp, PWM Dimming Output, Illumination Lamps for Microphone, RR and LR Door Ashtrays, Heated Seat Switches, Rear Defrost Control Switch, EATC Control Panel, Message Center Switches, Speed Control Switches, Cigar Lighter, Console and Ashtray Data Link Connector (DLC), Powertrain Control Module (PCM) Multi-Function Switch, Corner
Roadside emergencies Fuse/Relay Location Fuse Amp Rating 5 10A 6 10A 7 8 20A 20A 9 10A 10 30A 11 10A 12 10A Description Virtual Image Instrument Cluster, Lighting Control Module (LCM RUN/START Sense), Autolamp Light Sensor Virtual Image Instrument Cluster, RF Park/Turn Lamp Power Point Fuel Filler Door Release Switch, Trunk Lid Relay Air Bag Diagnostic Monitor, EATC Module, Blower Motor Relay Windshield Wiper Motor, Windshield Wiper Module Ignition Coils, Radio Interference Capacitor, PCM Power
Roadside emergencies Fuse/Relay Location Fuse Amp Rating 13 15A 14 15 20A 10A 16 17 18 30A 10A 19 10A 20 15A 21 22 23 10A 24 10A 25 10A 114 Description Lighting Control Module (LCM): RF Turn Lamp, Right Turn Indicator (VIC), RR Side Marker Lamps, Tail Lamps, License Lamps, LR Stop/Turn Lamps, Clock Illumination Cigar Lighter ABS Evac and Fill Connector Moonroof Switch NOT USED Lighting Control Module Lighting Control Module (LCM): Left Headlamp, DRL Multi-Function Switch: Flash to Pass, and
Roadside emergencies Fuse/Relay Location Fuse Amp Rating 26 10A 27 28 10A 29 30 31 10A 10A 15A 32 15A 33 - Description Virtual Image Instrument Cluster, EATC Module NOT USED Shift Lock Actuator, Vehicle Dynamic Module, Virtual Image Instrument Cluster, Rear Window Defrost, Heated Seat Switch Assembly, Low Tire Pressure Module Radio Heated Mirrors Lighting Control Module (LCM): FCU, Electronic Day/Night Mirror, RH and LH Courtesy Lamp, Door Courtesy Lamps, RH and LH Map Lamps, RR and LR Reading Lamp
Roadside emergencies Fuse/Relay Location Fuse Amp Rating 34 15A 35 36 37 30A 38 10A 39 10A 40 41 10A 20A 116 Description Console Shift Illumination, A/C Clutch Cycling Pressure Switch, A/C Clutch Relay (DTR) Sensor, Intake Manifold Runner Control, Backup Lamps NOT USED NOT USED Subwoofer Amplifier, Radio Analog Clock, CD Player, Mobile Telephone Transceiver, RESCU Power Door Locks, Power Seats, Power Mirrors, Keyless Entry, LF Seat Module, LF Door Module Cornering Lamps Door Locks
Roadside emergencies Power distribution box The power distribution box is located in the engine compartment near the battery. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses.
Roadside emergencies The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating 175 1 2 30A** 30A** 3 4 5 6 7 8 40A** 40A** 40A** 30A** 40A** 9 10 11 12 60A** 60A** 60A** 60A** 13 14 40A** 60A** 1 2 3 30A* 20A* 30A* 4 5 6 7 30A* 10A* 20A* 15A* 118 Description Generator/Voltage Regulator Driver’s Seat Module Passenger’s Seat Module Ignition Switch Ignition Switch Driver Window NOT USED PCM Power Rear Window Defrost Control I/P Fuse Panel LCM Power Compressor Relay Anti-Lo
Roadside emergencies Fuse/Relay Location Fuse Amp Rating 8 30A* 1 2 * Mini Fuses ** Maxi Fuses Description Front Passenger Window A/C Diode PCM Diode CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Tire change procedure 1. Park on a level surface, activate hazard flashers and set parking brake. 2. Place gearshift lever in P (Park). 3.
Roadside emergencies 5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. Refer to Anti-theft lug nuts for information on removing anti-theft lug nuts. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Refer to Air suspension system in the Driving chapter for more information. OFF 6.
Roadside emergencies 10. Remove the jack and fully tighten the lug nuts in the order shown. 11. Put flat tire, jack and lug wrench away. 12. Turn on the air suspension switch. 1 3 4 5 2 Anti-theft lug nuts (if equipped) If your vehicle is equipped with this feature, one of the lug nuts on each wheel must be removed and replaced with a special key. The key and registration card are attached to the lug wrench and stored with the spare tire.
Roadside emergencies JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. You could damage the catalytic converter. Batteries contain sulfuric acid which burns skin, eyes, and clothing. Preparing your vehicle Also see the label on the battery. 1. Use only a 12–volt supply to start your vehicle.
Roadside emergencies – – Connecting the jumper cables 1. Position the vehicles so that they do not touch one another. 4 2. Switch off the engine. Switch off any unnecessary electrical equipment. 1 + 3. Connect the positive (+) terminal of the discharged battery (1) to the positive (+) terminal of the booster battery (2). 4.
Roadside emergencies 124 4 + – + WRECKER TOWING 1 – Removing the jumper cables 1. Remove the jumper cables in reverse order. Take the cable off the alternator mounting brace stud (1) first, followed by the cable on the negative (-) booster battery terminal (2). 2. Remove the cable from the positive (+) terminal of the booster battery (3) and then the discharged battery (4). 3. After the disabled vehicle has been started, allow it to idle for a while so the engine can “relearn” its idle conditions.
Roadside emergencies If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. When calling for a tow truck, tell the operator what kind of vehicle you have. A towing manual is available from Ford Motor Company for all authorized tow truck operators.
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a “Service Guide” which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service. Check your “Warranty Guide” to find out which parts and services are covered. Use only recommended fuels, lubricants, fluids and service parts conforming to specifications.
Maintenance and care Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. Lift the hood until the lift cylinders hold it open. HOOD BRAKE RELEASE IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.
Maintenance and care 3. Engine coolant reservoir 4. Passenger compartment air filter assembly 5. Transaxle fluid dipstick 6. Brake fluid reservoir 7. Battery 8. Air filter assembly 9. Engine oil dipstick 10. Engine oil fill cap ENGINE OIL Checking the engine oil Check the engine oil each time you fuel your vehicle. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3.
Maintenance and care • If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range. • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil.
Maintenance and care Use SAE 5W-30 motor oil certified for gasoline engines by the American Petroleum Institute. Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by your warranty. Changing the engine oil and filter Change your engine oil and filter according to the appropriate schedule listed in the “Service Guide”.
Maintenance and care Brake fluid is toxic. If you use a brake fluid that is not DOT 3, you will cause permanent damage to your brakes. Do not let the reservoir for the master cylinder run dry. This may cause the brakes to fail. WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is symbol. highlighted with a If the level is low, add enough fluid to fill the reservoir. In very cold weather, do not fill the reservoir all the way.
Maintenance and care If the engine coolant has not been checked for a long period of time, the engine coolant reservoir may eventually empty. If this occurs, a LOW ENGINE COOLANT warning illuminate in the message center and you will need to add engine coolant to the coolant reservoir. For more information on engine coolant maintenance, refer to Adding engine coolant in this chapter.
Maintenance and care 2. When the engine is cool, wrap a thick cloth around the cap. Slowly turn cap counterclockwise. 3. Step back while the pressure releases. 4. When you are sure that all the pressure has been released, turn it counterclockwise and remove it. Use Ford Premium Cooling System Fluid E2FZ-19549–AA (in Canada, Motorcraft CXC-8–B) or an equivalent premium engine coolant that meets Ford specification ESE-M97B44–A.
Maintenance and care coolant concentration above 60%. Leave a 50/50 mixture of engine coolant and water in your vehicle year-round in non-extreme climates. CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid at least twice a year. If adding fluid is necessary, use only MERCONt ATF power steering fluid. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge will be near the center of the NORMAL band). 2.
Maintenance and care Before adding any fluid, make sure the correct type is used . The type of fluid used is normally indicated on the dipstick and/or dipstick handle and also in the Lubricant specifications section in the Capacities and specifications chapter. Do not drive the vehicle if the fluid level is below the hole at the bottom of the dipstick and outside temperatures are above 10°C (50°F). Your transmission does not use up fluid.
Maintenance and care 8. If an overfill occurs, excess fluid should be removed by a qualified technician. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. If the fluid level is above the crosshatch (hot operating range) area after driving the vehicle for approximately 30 km (20 miles), excess transmission fluid should be removed by a qualified technician. BATTERY Your vehicle may be equipped with a Superstart maintenance-free battery.
Maintenance and care If your battery has a cover/shield, make sure it is reinstalled after the battery is replaced. Because your vehicle’s engine is electronically controlled by a computer, some control conditions are maintained by power from the battery. When the battery is disconnected or a new battery is installed, the engine must relearn its idle conditions before your vehicle will drive properly. To begin this process: 1. Put the gearshift in P (Park), turn off all accessories and start the vehicle. 2.
Maintenance and care CABIN AIR FILTER The cabin air filter restricts the entry of airborne dust and pollen particles. The filter is located just in front of the windshield under the cowl vent screen on the passenger side of the vehicle. To replace the filter, perform the following procedure: 1. In order to gain better access to the filter, turn the ignition key to ON, then turn the wipers on. When the wipers reach the middle of the windshield (wipers in straight up position), turn the ignition to OFF. 2.
Maintenance and care 3. Pull the rubber cowl seal (number 1 in figure) away from the cowl vent screen. Remove the right half of the cowl vent screen (number 2 in figure) by placing your hand underneath the cowl vent screen and lifting straight up to release the four spring clips. 2 1 4. Remove the water shield (number 3 in figure) by disengaging the two water shield locking tabs (number 4 in figure), then sliding the water shield toward the front of the vehicle.
Maintenance and care Checking the wiper blades If the wiper blades do not wipe properly, clean both the windshield and wiper blades using undiluted windshield wiper solution or a mild detergent. Rinse thoroughly with clean water. To avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents. Changing the wiper blades When replacing wiper blade assemblies, always use a Motorcraft part or equivalent.
Maintenance and care • do not exceed 90 km/h (55 mph). Drive at a reduced rate of speed, if possible. • avoid excessive hard steering and braking maneuvers, if possible. • stop periodically to allow the tires to cool down. Pressure alert system (if equipped) Each of your SecuriTires is monitored by a low tire pressure sensor. A warning will appear in the overhead console when the pressure LOW TIRE in one of your tires drops below PRESSURE acceptable levels or if the system has malfunctioned.
Maintenance and care your SecuriTire requires service as soon as possible. Refer to Servicing your SecuriTires. The Pressure Alert System will activate only when the vehicle is moving faster than 15 km/h (10 mph). Servicing your SecuriTires If you cannot service your SecuriTire immediately, replace it with your temporary spare as soon as safely possible. Your temporary spare tire can be used until your SecuriTire has been repaired.
Maintenance and care Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire grade 150 would wear one and one-half (1 1/2) times as well on the government course as a tire grade 100.
Maintenance and care SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles). • Adjust tire pressure to recommended specifications found on the Safety Compliance Certification Label located on the right rear door jamb.
Maintenance and care Replacing the tires Replace the tires when the wear band is visible through the tire treads. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier to lose control and roll over. Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer. SNOW TIRES AND CHAINS Driving too fast for conditions creates the possibility of loss of vehicle control.
Maintenance and care WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. If you do not use the proper fuel cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision. The fuel system may be under pressure.
Maintenance and care • Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors or skin contact could cause an adverse reaction. Consult a physician immediately. Choosing the right fuel Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle. Your vehicle was not designed to use fuel or fuel additives with metallic compounds, including manganese-based compounds containing MMT.
Maintenance and care The American Automobile Manufacturers Association (AAMA) issued a gasoline specification to provide information on high quality fuels that optimize the performance of your vehicle. We recommend the use of gasolines that meet the AAMA specification if they are available. It should not be necessary to add any aftermarket products to your fuel tank if you continue to use a high-quality fuel.
Maintenance and care EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. To make sure that the catalytic converter and other emission control components continue to work properly: • Use only unleaded fuel. • Avoid running out of fuel. • Do not turn off the ignition while your vehicle is moving, especially at high speeds.
Maintenance and care the Vehicle Emission Control Information Decal located on or near the engine. This decal identifies engine displacement and gives some tune up specifications. Please consult your “Warranty Guide” for complete emission warranty information. Readiness for inspection/maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostic (OBD-II) system.
Maintenance and care 3. At the back of the headlamp, pull back and up slightly on the two right angle brackets to release the headlamp assembly from the vehicle. 4. Carefully pull the headlamp assembly away from the vehicle to expose the back of the bulb and wiring connector. 5. Disconnect the electrical connector from the bulb by pulling the connector rearward. 6.
Maintenance and care 5. Turn the headlamps on and make sure they work properly. If the headlamp was correctly aligned before you changed the bulb, you should not need to align it again. AIMING THE HEADLAMPS Your vehicle is equipped with a Vehicle Headlamp Aim Device (VHAD) on each headlamp. Each headlamp may be properly aimed in the vertical (up/down) and the horizontal (left/right) directions using your VHAD system. The headlamps on your vehicle are properly aimed at the assembly plant.
Maintenance and care 2. Use a 4mm wrench or socket to turn the horizontal adjusting screw until the “0” mark on the yellow dial lines up with the reference mark on the marker (as shown) when viewed directly from above. Turning the horizontal adjusting screw in the direction of the arrow changes the horizontal aim as shown. Vertical aim adjustment 1. Park the vehicle on a level surface. 2. With the hood open, locate the bubble level and vertical adjustment screw.
Maintenance and care D U 3. The “U” and “D” on the bubble indicate the directional change (up or down) of the vertical aim. 4. Use a 4 mm wrench or socket to turn the vertical adjusting screw until the bubble is centered between the two red lines which represents the “0” mark position. When the horizontal and vertical indicators are set to the “0” mark, the headlamp has been properly aimed. 5. Replace the protective cover.
Maintenance and care Function Trade Number Door mounted lamp (front) 214-2 Illuminated visor mirror 74 Overhead console reading lamp (without 912 moon roof) Passenger assist handle (rear seat) 211-2 To replace all instrument panel lights - see your dealer. CLEANING AND CARING FOR YOUR VEHICLE Refer to the “Customer Assistance Guide” for a list of Ford-approved cleaners, polishes and waxes. Washing your vehicle Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap.
Maintenance and care Repairing paint chips Minor scratches or paint damage from road debris may be repaired with touch-up paint, repair foil or aerosol paint spray from the Ford accessory line. Observe the application instructions on the products. Remove particles such as bird droppings, tree sap, insect remains, tar spots, road salt and industrial fallout immediately. Cleaning the wheels Wash with the same detergent as the body of your vehicle.
Maintenance and care • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary. Do not clean plastic parts with thinners, solvents or petroleum-based cleaners. Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. Use glass cleaner or tar remover if necessary.
Maintenance and care Cleaning leather seats For routine cleaning, wipe the surface with a soft, damp cloth. For more thorough cleaning, wipe the surface with a leather and vinyl cleaner or a mild soap. The type of scrubbing pad is very critical because the common 3M “Scotch Brite” green pad is too aggressive and will damage the leather surface. • Spray a small amount of the leather cleaner on the pad and rub the area to be cleaned with the pad using a circular motion. Only clean 1/4 of the area at a time.
Maintenance and care Inside windows Use glass cleaner for the inside windows if they become fogged. Cleaning mirrors Do not clean your mirrors with a dry cloth or abrasive materials. Use a soft cloth and mild detergent and water. Be careful when removing ice from outside mirrors because you may damage the reflective surface.
Capacities and specifications MOTORCRAFT PART NUMBERS Component 4.6L DOHC V8 engine Air filter FA-1615 Cabin air filter FP-5 Fuel filter FG-800A Battery BXT-65-750 Oil filter FL-820-S Spark plugs* AWSF-32EE** * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. **If a spark plug needs to be replaced, use only spark plugs with the same service part number suffix letter “EE” as shown on the engine decal.
Capacities and specifications Fluid Fuel tank Automatic transaxle Windshield washer fluid Ford Part Name N/A Application Capacity All Motorcraft MERCONtV ATF Ultra-Clear Windshield Washer Concentrate All 75.7L (20.0 gallons) 13.0L (13.
Capacities and specifications Item Engine oil Constant velocity joints Engine coolant Power steering fluid Windshield washer fluid Ford Part Ford Part Name or Number equivalent Motorcraft 5W30 XO-5W30-QSP Super Premium Motor Oil CV Joint Grease (High Temp.
Capacities and specifications VEHICLE DIMENSIONS Vehicle dimensions (1) Overall length (2) Overall width (3) Overall height (4) Wheelbase (5) Track - Front (5) Track - Rear mm (in) 5 294.7 (208.4) 1 870.3 (76.3) 1 421.9 (55.9) 2 769.8 (109.0) 1 600.2 (63.0) 1 562.1 (61.
Capacities and specifications 3 5 2 IDENTIFYING YOUR VEHICLE Safety compliance label The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the front door latch pillar on the driver’s side. MFD. BY FORD MOTOR CO. IN U.S.A.
Capacities and specifications Vehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. AIR BAG XXXXXXXXXXXXXXXXX ENGINE NUMBER The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame and transfer case (if so equipped).
Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Index Air bag supplemental restraint system ..........................................80 and child safety seats ..............81 description ................................80 disposal ......................................83 indicator light ...........................82 passenger air bag .....................81 Air suspension description ................................98 Anti-lock brake system (ABS)#$description Anti-theft system ........................63 Battery .......................................
Index high beam .................................26 Heating ........................................27 High beams indicator light .............................8 Hood release lever ............................127 Ignition positions of the ignition ...........34 Jump-starting your vehicle .....122, 123 attaching cables ......................123 disconnecting cables ..............124 Keyless entry system autolock .....................................70 keypad .......................................
Index Speed control ..............................36 canceling a set speed ...............39 resuming a set speed ...............39 tap up/tap down .......................38 turning off .................................37 Speedometer ...............................10 Starting your vehicle .............90,92 Sunvisor .......................................52 Tachometer mechanical cluster ...................11 Tilt steering wheel ......................40 Tires ....................................
Filling station information Recommended fuel Fuel tank capacity Engine oil capacity (with filter change) Automatic transaxle fluid capacity Tire size and pressure Hood release Coolant capacity Power steering fluid capacity Unleaded fuel only - 91 octane (R+M/2) 75.7L (20.0 gallons) 5.7L (6.0 quarts). Use Motorcraft 5W30 Super Premium Motor Oil, Ford Specification WSS-M2C153-G 13.0L (13.7 quarts).