Contents Before driving Introduction 2 Instrumentation 6 Controls and features 18 Seating and safety restraints 87 Starting and driving Starting 128 Driving 133 Roadside emergencies 157 Servicing Maintenance and care 179 Capacities and specifications 227 Customer assistance 235 Reporting safety defects 247 Index 248 All rights reserved.
Introduction The following warning may be required by California law: CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction BREAKING-IN YOUR VEHICLE There are no particular breaking-in rules for your vehicle. During the first 1 600 km (1 000 miles) of driving, vary speeds frequently. This is necessary to give the moving parts a chance to break in. INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation. SPECIAL NOTICES Using your vehicle with a snowplow Do not use this vehicle for snowplowing.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Emission System Engine Air Filter Passenger Compartment Air Filter Jack MAX MIN 5
Instrumentation Turn signal and wiper/washer control (pg. 59) Instrument cluster (pg. 8) Gearshift (includes overdrive button) (pg. 142) Headlamp control (pg. 18) DOOR AJAR H 60 80 F 4X4 L 40 20 LOW FUEL SERVICE ENGINE SOON H NAVIGATOR 20 40 L THEFT 00 LOW RANGE 60 MPH D 2 P RN D E H RPMX1000 km/h SELECT RESET CK SUSP C BRAKE INT 2 INT 1 OFF RESUME NEXT SET ACCEL MODE COAST OFF ON PEDALS Rear window defroster control (pg.
Instrumentation Clock (pg. 24) H Electronic sound system (pg. 25) M BASS BAL SEL TREB VOL PUSH ON OVERDRIVE OFF CD EJ TAPE AM A4WD FM REW FF SIDE 1.2 1 2 3 SCAN 6 MAX A/C VENT HI AUTOMATIC OUTSIDE TEMP Auxiliary climate controls (pg. 61) SHUFF 5 OFF 4L AUTO COMP 4 4H Radio controls (pg. 61) RDS TUNE SEEK MUTE FADE PNL FLR FLOOR 4wd control* (pg. 144) FLR DEF DEF Auxiliary power point (pg. 23) LO Climate control system (pg.
Instrumentation WARNING LIGHTS AND CHIMES DOOR AJAR H 60 40 L 80 00 F E H NAVIGATOR 4X4 20 L 40 20 LOW FUEL SERVICE ENGINE SOON THEFT LOW RANGE 60 MPH H RPMX1000 km/h D 2 P RN D SELECT RESET BRAKE CK SUSP C Low fuel Illuminates as an early reminder of a low fuel condition indicated on the fuel gauge (refer to Fuel Gauge in this chapter for more information).
Instrumentation What you should do if the Service Engine Soon light illuminates Light turns on solid: This means that the OBD II system has detected a malfunction. Temporary malfunctions may cause your Service Engine Soon light to illuminate. Examples are: 1. The vehicle has run out of fuel. (The engine may misfire or run poorly.) 2. Poor fuel quality or water in the fuel. 3. The fuel cap may not have been properly installed and securely tightened.
Instrumentation Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter. Brake system warning Momentarily illuminates when the ignition is turned to the ON BRAKE position. Also illuminates if the ! parking brake is engaged. If the brake warning lamp does not illuminate at these times, seek service immediately.
Instrumentation High beams Illuminates when the high beam headlamps are turned on. SecuriLockY anti-theft system This light indicates the anti-theft alarm system is armed. Momentarily THEFT illuminates when the ignition is turned to ON/START. If the light fails to illuminate, continues to flash or remains on, have the system serviced. Refer to SecuriLocky passive anti-theft system in the Controls and features chapter.
Instrumentation Four wheel drive low (if equipped) Momentarily illuminates when the LOW ignition is turned to the START RANGE position. Illuminates when four-wheel drive low is engaged. If the light continues to flash have the system serviced. Four wheel drive indicator (if equipped) Momentarily illuminates when the 4x4 ignition is turned to the ON position. Illuminates when 4x4 range is engaged. If the light continues to flash have the system serviced.
Instrumentation For information on the safety belt warning chime, refer to the Seating and safety restraints chapter. Supplemental restraint system (SRS) warning chime For information on the SRS warning chime, refer to the Seating and safety restraints chapter. Key-in-ignition warning chime Sounds when the key is left in the ignition in the OFF/LOCK or ACC position and the driver’s door is opened.
Instrumentation A minimum of 22.2 L (six gallons) must be added or removed from the fuel tank in order for the gauge to instantaneously update. If less than six gallons is the change, the gauge will take between five to twenty minutes to update. Speedometer Indicates the current vehicle speed. 60 80 00 20 40 40 20 60 MPH Engine coolant temperature gauge Indicates the temperature of the engine coolant.
Instrumentation Odometer Registers the total kilometers (miles) of the vehicle. Trip odometer Registers the kilometers (miles) of individual journeys. Press and release the reset button until a “T” appears in the display (this represents the trip mode). Press and hold the button for three seconds to reset. Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine.
Instrumentation Engine oil pressure gauge This shows the engine oil pressure in the system. Sufficient pressure exists as long as the needle remains in the normal range (the area between the “L” and “H”). H If the gauge indicates low pressure, stop the vehicle as soon as safely possible and switch off the engine L immediately. Check the oil level. Add oil if needed (refer to Engine oil in the Maintenance and care chapter).
Instrumentation Mode control Each press of the MODE control will display a different feature as follows: MODE E/M Fuel range. This displays the RESET approximate number of kilometers (miles) left to drive before the fuel MILES tank is empty. The indicated TO EMPTY distance to empty may be inaccurate: • with sustained, drastic changes in fuel economy (such as trailer towing), but will eventually recover. • if the vehicle is started while parked on an incline.
Controls and features HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. A High beams Push forward to activate. Pull toward you to deactivate. Flash to pass Pull toward you to activate and release to deactivate. Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output.
Controls and features Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Light (DRL) System does not activate your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision. Foglamp control (if equipped) The headlamp control also operates the foglamps.
Controls and features AUTOLAMP CONTROL The autolamp system provides light sensitive automatic on-off control of A the exterior lights normally controlled by the headlamp control. The autolamp system also keeps the lights on for approximately 20 seconds after the ignition switch is turned to OFF. • To turn autolamps on, rotate the control counterclockwise. • To turn autolamps off, rotate the control clockwise to OFF. • Foglamps are not controlled by the autolamps.
Controls and features REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog. • A small LED will illuminate when the rear defroster is activated. The ignition must be in the ON position to operate the rear window defroster. The defroster turns off automatically after 10 minutes or when the ignition is turned to the OFF position.
Controls and features To help avoid personal injury, always use caution when in reverse and when using the reverse sensing system. This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle. The system may not detect smaller objects, particularly those close to the ground.
Controls and features disable the reverse sensing system only when the ignition is ON, and the gear selector is in R (Reverse). The OFF indicator remains illuminated when the system is disabled. The system defaults to ON every time the reverse gear is selected. Press the control to disable or enable the system. The indicator will remain illuminated to indicate a failure of the reverse sensing system.
Controls and features A second auxiliary power point is located on the lower rear side of the console. The power point is accessible from the rear seats. CLOCK Press H to set the hour. Press M to set the minute.
Controls and features USING YOUR AUDIO SYSTEM Premium AM/FM Stereo/Cassette (CD Changer Compatible) BASS BAL SEL TREB VOL PUSH ON CD EJ TAPE AM FM RDS TUNE SEEK MUTE REW FF SIDE 1.
Controls and features Your audio system is equipped with selective lighting, a unique lighting strategy. This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off. Those controls which have a function for the specific mode of operation selected will be lit, while the controls which have no function for that mode will be turned off.
Controls and features With the radio on, press and hold the volume control for five seconds, until the display reads SPEED VOL #, then press: VOL PUSH ON • to increase volume compensation • to decrease or shut off the volume compensation AM/FM select The AM/FM select control works in radio, tape and CD modes (if equipped). SEL AM FM AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations.
Controls and features • Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold for quick movement. Tune adjust for CD changer • Press to select the previous TUNE disc in the CD changer. (Play will begin on the first track of the disc unless the CD changer is in shuffle mode.) Refer to Shuffle feature for more information. Hold the control to continue reversing through the discs. to select the next disc in the CD changer.
Controls and features Scan function The scan function works in radio, tape or CD mode (if equipped). SCAN Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode. Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction.
Controls and features Autoset memory preset Autoset allows you to set strong radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations AUTO are filled, the station stored in memory preset control 1 will start playing.
Controls and features Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control. Use the SEL control to adjust the sound between the speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the FADE control. Use the SEL control to adjust the sound between the front and rear speakers.
Controls and features • In CD mode, pressing the REW control for less than three seconds results in slow rewind. Pressing the control for more than three seconds results in fast rewind. Fast forward The fast forward control works in FF tape and CD modes (if equipped). 2 • In the tape mode, tape direction will automatically reverse when the end of the tape is reached. • In CD mode, pressing the control for less than three seconds results in slow forward action.
Controls and features Compression feature Compression adjust brings soft and COMP loud CD passages together for a more consistent listening level. 5 Press the COMP control to activate and deactivate compression adjust. The effect of the feature varies with the music content. Shuffle feature The shuffle feature operates in CD SHUFF mode and plays all tracks on the current disc in random order. If 6 equipped with the CD changer, the shuffle feature continues to the next disc after all tracks are played.
Controls and features Radio data system (RDS) feature This feature allows your audio system to receive station DSP RDS identification or program type from RDS-equipped FM radio stations. The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC) recommend FM radio broadcasters to use RDS technology to transmit information.
Controls and features • Use the SEL control to select the program type. With the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: • Classic • Country • Info • Jazz • Oldies • R&B • Religious • Rock • Soft • Top 40 Show • With RDS activated, press the RDS control until SHOW is displayed. • Use the SEL control to select TYPE (the display shows the program type), NAME (the display shows the call letters of the station) or NONE.
Controls and features Use the SEL control to select the desired signal mode (the selected mode will appear in the display). SEL The following signal modes can be selected: • JAZZ CLUB—jazz club with clearly reflected sounds. • HALL—rectangular concert hall capacity of about 2 000 • CHURCH—church with a high vault. • STADIUM—outdoor stadium with a capacity of about 30 000. • NEWS—“voice-only” type of sound with a limited audio band.
Controls and features To turn on the rear seat controls, 1 2 3 5 6 4 press the memory preset controls 3 and 5 at the same time. The will appear in the display. Pressing 3 and 5 at the same time again will turn the rear seat controls off. If there is a discrepancy between the rear seat and the front audio controls, (such as both trying to listen to the same playing media), the front audio system will receive the desired selection. REW Adjusting the volume Press the + control to increase volume.
Controls and features Using headphones Plug a 3.5 mm headphone (not included) into the jack. Press the speaker on/off control to operate the headphones. The speakers will cut out once the speaker on/off control is pressed. Press the control again to deactivate the headphones. Mode select Push the MODE control to toggle between AM, FM1, FM2, tape, CD or CD changer (if equipped).
Controls and features Seek function • In radio mode, press to find the next listenable station down the frequency band. • In radio mode, press to find the next listenable station up the frequency band. • In tape mode, use the SEEK function to access the next or previous selection. • In CD mode (if equipped), use the SEEK function to access the next - VOLUME + MODE SEEK MEMORY or previous selection. CD changer (if equipped) Your CD changer is located in the center console.
Controls and features 1. Pull the lever to remove a CD tray from the magazine. 2. Insert one disc into each CD tray of the magazine (up to 6 discs). Ensure that the label side is facing up. If you pull too hard on the disc holder, the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine. 3. Insert each CD tray, with the disc loaded, all the way into the CD magazine. 4. Insert the CD magazine into the changer.
Controls and features 5. Slide the door to the left to close. Use only compact discs containing this mark. The magazine does not need to be full for the changer to operate. Radio power must be turned on to play the CDs in the changer. The magazine may be stored in the glove compartment when not being used. The CD magazine may be inserted or ejected with the radio power off. Keep the CD changer door closed. Coins and foreign objects will damage the CD player and void your audio system warranty.
Controls and features Cleaning compact discs Inspect all discs for contamination before playing. If necessary, clean discs only with an approved CD cleaner and wipe from the center out to the edge. Do not use circular motion. CD and CD changer care • Handle discs by their edges only. Never touch the playing surface. • Do not expose discs to direct sunlight or heat sources for extended periods of time. • Do not insert more than one disc into each slot of the CD changer magazine.
Controls and features Radio reception factors Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their strength/volume relative to other stations. • Terrain.
Controls and features Turning the EATC on Press AUTOMATIC, any of the override controls or the fan speed control. The EATC will only operate when the vehicle is running. MAX A/C VENT Turning the EATC off Press OFF. The Outside Temperature function will continue to operate until the ignition is turned off. PNL • FLR FLOOR OFF HI OFF F AUTO OUTSIDE TEMP AUTOMATIC FLR • DEF DEF LO HI AUTOMATIC FLR • DEF DEF LO Automatic operation Press AUTOMATIC and select the desired temperature.
Controls and features Temperature selection The display window indicates the selected temperature, function (AUTO or one of the override controls) and manual control of fan speed ( ) if automatic fan speed is not desired. To control the temperature, select any temperature between 18°C (65°F) and 29°C (85°F) by pressing the blue (cooler) or red (warmer) buttons.
Controls and features Fan speed ( ) When AUTOMATIC is pressed, fan speed is adjusted automatically for existing conditions. You can override fan speed at any time. To control fan speed manually, use the thumbwheel or steering wheel control to cancel automatic fan speed operation. HI OFF AUTOMATIC FLR • DEF DEF LO • Rotate the thumbwheel up for higher fan speed or down for lower fan speed. • Press the steering wheel control up for higher fan speed or down for lower fan speed.
Controls and features • MAX A/C-Uses recirculated air to cool the vehicle. The temperature will display 16°C (60°F). To exit, press AUTOMATIC or any other override controls. MAX A/C is noisier than normal A/C but more economical and will cool the inside of the vehicle faster. Airflow is from the instrument panel registers. This mode can also be used to prevent undesirable odors from entering the vehicle. • VENT-Distributes outside air through the instrument panel registers.
Controls and features Displaying outside temperature Press OUTSIDE TEMP to display the outside air temperature. It will be displayed until OUTSIDE TEMP is pressed again. OUTSIDE TEMP MAX A/C VENT PNL • FLR If the selected temperature is changed while the outside temperature is displayed, the new temperature will be displayed for four seconds after it is changed, then the outside temperature will return to the window.
Controls and features • Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield). • If your vehicle has been parked with the windows closed during hot weather, the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open. This will force most of the hot, stale air out of the vehicle. Then operate the air conditioner as you would normally. • Do not place objects over the defroster outlets.
Controls and features Your climate controls will either be located on the rear of the center console, OFF LO HI COOL WARM PANEL - VOLUME + MODE SEEK MEMORY FLOOR or located in the overhead console. OFF LO HI COOL WARM PANEL FLOOR Turn the air distribution control to the desired airflow position. Turn the fan speed control to the desired position. Auxiliary A/C-heater controls (if equipped) The auxiliary A/C-heater feature provides increased capacity to quickly heat or cool the vehicle.
Controls and features Your auxiliary A/C controls may be located in the floor console, R OO FL F OF RM WA AR RE L NE PA HI OL CO or located in the overhead console.
Controls and features In order for the auxiliary A/C-heater controls to function, the driver’s auxiliary A/C-heater control must be set to REAR. OFF REAR HI COOL The instrument panel climate controls must be on in order for the auxiliary A/C-heater to operate.
Controls and features POSITIONS OF THE IGNITION 1. ACCESSORY, allows the electrical 4 accessories such as the radio to 3 operate while the engine is not 5 running. 2. LOCK, locks the steering wheel, 2 automatic transmission gearshift lever and allows key removal. 1 3. OFF, shuts off the engine and all accessories without locking the steering wheel. 4. ON, all electrical circuits operational. Warning lights illuminated. Key position when driving. 5. START, cranks the engine.
Controls and features SPEED CONTROL To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. Do not shift the gearshift lever into N (Neutral) with the speed control on.
Controls and features To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. To set a speed • Press SET/SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal.
Controls and features speed while driving on a downhill, you may want to shift to the next lower gear or apply the brakes to reduce your vehicle speed. If your vehicle slows down more than 16 km/h (10 mph) below your set speed on an uphill, your speed control will disengage. This is normal. Pressing RES/RSM/RESUME will re-engage it. Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. To set a higher set speed • Press and hold SET/SET ACC/ SET ACCEL.
Controls and features To set a lower set speed • Press and hold CST/COAST. Release the control when the desired speed is reached or • Press and release CST/COAST to operate the Tap-Down function. Each press will decrease the set speed by 1.6 km/h (1 mph) or • Depress the brake pedal. When the desired vehicle speed is reached, press SET/SET ACC/ SET ACCEL.
Controls and features To disengage speed control • Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. To return to a previously set speed • Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph).
Controls and features TILT STEERING Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control. Never adjust the steering wheel when the vehicle is moving. HAZARD FLASHER For information on the hazard flasher control, refer to Hazard flasher in the Roadside emergencies chapter.
Controls and features Rear window wiper/washer controls For rear wiper operation, rotate the rear window wiper and washer control to the desired position. Select: INT 2 — One second interval rear wiper. INT 1 — Ten second interval rear wiper. OFF — Rear wiper and washer off. For rear wash cycle, rotate (and hold as desired) the rear wiper/washer control to either position. From either position, the control will automatically return to the INT2 or OFF position.
Controls and features The TCIL (the word OFF) will no longer be illuminated. When you shut off and re-start your vehicle, the transmission will automatically return to normal (Overdrive) mode. For additional information about the gearshift lever and the transmission control switch operation refer to the Automatic Transmission Operation section of the Driving chapter. STEERING WHEEL CONTROLS These controls allow you to operate some radio and climate control features.
Controls and features OVERHEAD CONSOLE The appearance of your vehicle’s overhead console will vary according to your option package. Forward storage bin (if equipped) Press the release control to open the storage compartment. The door will open slightly and can be moved to full open. The storage compartment may be used to secure sunglasses or a similar object.
Controls and features One-touch moon roof (if equipped) • Press and release the rear portion of the moon roof control to open. • Press and hold (as desired) the front portion of the moon roof control to close. • To halt motion at any point during one-touch opening, press the control a second time. • The moon roof has a sliding shade that can be manually opened or closed when the glass panel is shut. • To close the shade, pull it toward the front of the vehicle.
Controls and features Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 1 15 2 14 3 13 4 12 11 5 6 10 7 8 9 2. Locate the compass module mounted on the center rear view mirror post. 3. Turn ignition to the ON position. 4. Press and hold the RESET button on top of the compass module until the message display in the trip computer shows the current zone setting. 5. Release the RESET button. 6.
Controls and features 2. Press and hold the RESET button on the compass module until CAL indicator is displayed in the trip computer. 3. Release pressure from the RESET button. 4. Slowly drive the vehicle in a circle (less than 5 km/h [3 mph]) until the CAL indicator turns off. This will take three to five circles to complete calibration. 5. The compass is now calibrated.
Controls and features Press the portion of the VENT control to close the power rear quarter windows. Interior Lamps Map lamps To turn on the map lamps, press the control next to each lamp. VENT ROOF VENT Rear dome lamp The dome lamp lights when: • any door is opened. • the instrument panel dimmer switch is held up until the courtesy lamps come on. • any of the remote entry controls are pressed and the ignition is OFF.
Controls and features Do not block the sensor on the backside of the inside rear view mirror since this may impair proper system performance. Press the control to turn the mirror OFF or AUTO. The mirror will automatically return to the normal state whenever the vehicle is placed in R (Reverse)(when the mirror is on) to ensure a bright clear view when backing up. OFF AUTO ILLUMINATED VISOR MIRROR (IF EQUIPPED) To turn on the visor mirror lamps, slide the mirror cover open.
Controls and features Programming 1. Prepare for programming the HomeLinkt Universal Transceiver by erasing the three factory default codes by holding down the two outside buttons until the red light begins to flash after 20 seconds. Release both buttons. 2. Hold the end of your hand-held transmitter 5–14 cm (2–5 inches) away from the HomeLinkt Universal Transceiver surface (located on your visor) while keeping the red light in view. 3.
Controls and features To program your hand-held transmitters: • continue to hold the button on the HomeLinkt Universal Transceiver. • press and re-press the hand-held transmitter button every two seconds until the red light changes from a slow to a fast flash. Operating the HomeLinkT Universal Transceiver Once programmed, the HomeLinkt Universal Transceiver can be used in place of hand-held transmitters.
Controls and features 3. Press and release the programmed HomeLinkt button. Press and release the HomeLinkt button a second time to complete the training process. (Some garage door openers may require this procedure to be done a third time to complete the training). The 2nd or 3rd press from step 3 will activate the door. The HomeLinkt Universal Transceiver has now been trained to the receiver. The remaining two buttons may now be programmed if this has not previously been done.
Controls and features POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. AUTO • Press the bottom portion of the rocker switch to open. AUTO One touch down • Press AUTO completely down and release quickly. The driver’s window will open fully. Depress again to stop window operation. One touch down can be deactivated during operation by pushing the top portion of the power window control.
Controls and features Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls WINDOW LOCK except for the driver’s press the left side of the control. Press the right side to restore the window controls. Accessory delay With accessory delay, the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until any door is opened.
Controls and features POWER SIDE VIEW MIRRORS The ignition can be in any position to adjust the power side view mirrors. To adjust your mirrors: 1. Select L to adjust the left mirror or R to adjust the right mirror. MIRRORS L 2. Move the control in the direction you wish to tilt the mirror. R MIRRORS L R 3. Return to the center position to lock mirrors in place. Press the control to retract or extend the outside rear view mirrors.
Controls and features Heated outside mirrors Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors. Signal mirrors When the turn signal is activated, the outer portion of the appropriate mirror housing will blink yellow.
Controls and features • • • • • Cupholders Coin holder slots Tissue box holder Compact disc changer (if equipped) Cellular phone (if equipped) Use only soft cups in the cupholder. Hard objects can injure you in a collision. Navigation system (if equipped) The navigation system is located in the center console. For information on operating the navigation system, refer to the Navigation System Supplement.
Controls and features POSITIVE RETENTION FLOOR MAT Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. To remove the floor mat, reverse the installation procedure. LIFTGATE To open the rear window, pull the left side of the liftgate handle. To open the liftgate, pull the right side of the liftgate handle.
Controls and features SECURILOCKY PASSIVE ANTI-THEFT SYSTEM Your vehicle is equipped with a coded-key anti-theft system. Only the correct key will be able to start your vehicle. If your keys are lost or stolen, you must take your vehicle to your dealership for key reprogramming. This system provides an advanced level of vehicle theft protection. Your vehicle’s engine can only be started with the two coded keys provided with your vehicle.
Controls and features Theft indicator The theft indicator in the instrument cluster will operate as follows: • When the ignition is OFF, the theft indicator will flash briefly every two seconds to indicate the anti-theft system is protecting your vehicle. • When the ignition is turned to ON or START, the theft indicator will light for three seconds and then go out.
Controls and features 4. Turn the ignition to OFF and remove the second coded key from the ignition. 5. Within 10 seconds of turning the ignition to OFF, insert the new unprogrammed key (new key/valet key) into the ignition and turn the ignition from OFF to ON (maintain ignition in ON for at least one second). This step will program your new key to a coded key. 6. To program additional new unprogrammed key(s), repeat this procedure from step 1.
Controls and features Unlocking the doors Press this control to unlock the driver door. The interior lamps and running board lamps will illuminate. The memory mirrors/seat will also be moved to position 1, 2 or 3 depending upon which remote entry transmitter (1, 2 or 3) is used. Press the control a second time within three seconds to unlock all doors. Locking the doors Press this control to lock all doors. To confirm doors are closed and locked, press this control a second time within three seconds.
Controls and features Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Replacing the battery The remote transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle.
Controls and features Replacing lost transmitters If a remote transmitter has been lost and you would like to remove it from the vehicle’s memory, or you would like to purchase additional remote transmitters and have them programmed to your vehicle: • Take all your vehicle’s transmitters to your dealer for programming, or • Perform the programming procedure yourself Programming remote transmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prio
Controls and features Illuminated entry The illuminated entry system will turn on the interior lights when the remote transmitter unlock control is pressed. The illuminated entry system will turn off the interior lights if the ignition switch is turned to the ON position, or if the remote transmitter lock control is pressed, or after 25 seconds of illumination. The inside lights will not turn off if: • they have been turned on with the dimmer control or • any door is open.
Controls and features 1. Turn the ignition key to ON. 2. Press the power door unlock control three times. 3. Turn the ignition key from ON to OFF. 4. Press the power door unlock control three times. 5. Turn the ignition back to ON. The horn will chirp. 6. Press the power door unlock control two times, then press the power lock control once. The horn will chirp twice if the memory feature was deactivated or three times (two short and one long chirp) if the memory feature was activated. 7.
Controls and features 6. Press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. 7. Turn the ignition to OFF. The horn will chirp once to confirm the procedure is complete. Keyless entry system With the keyless entry keypad, you can: • lock or unlock the vehicle doors without using the key. Your vehicle has a factory set 5 digit code that operates the keyless entry system.
Controls and features If you wish to erase your personal code, use the following instructions: 1. Enter factory set code. 2. Press 1/2 control within five seconds of step one. 1 2 3 4 5 6 7 8 9 0 3. Press 7/8 control and 9/0 control at the same time within five seconds of step 2. The system will now only respond to the factory set code.
Seating and safety restraints SEATING Adjustable head restraints (if equipped) Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. Refer to the following to raise and lower the head restraints.
Seating and safety restraints Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’s safety belt in the event of a collision.
Seating and safety restraints Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down.
Seating and safety restraints Memory seats/rearview mirrors/adjustable pedals (if equipped) This system allows automatic positioning of the driver seat, outside rearview mirrors, and SET adjustable pedals to three programmable positions. The memory seat control is located on the driver door. 1 2 • To program position one, move the driver seat to the desired position using the seat controls. Press the SET control. The SET control indicator light will briefly illuminate.
Seating and safety restraints CLIMATE CONTROL SEATS (if equipped) To operate the climate control seats the engine must be running. to heat • Slide the control to the seatback and the seat cushion. • Slide the control to to cool the seatback and the seat cushion. 5 3 In heat mode: • Rotate the thumbwheel to select the desired heat level from 0 (OFF) to 5 (MAX). In cool mode: • Rotate the thumbwheel to select the desired cooling level from 0 (OFF) to 5 (MAX).
Seating and safety restraints • There is a filter located under both front seats and can be accessed from the second row seat. Move the front seat all the way forward and up to ease access.
Seating and safety restraints To remove climate control seat air filter: • Remove key from ignition. • Push on the outside rigid edge of the air filter at the center and rotate downward once tab is released. Remove filter. ,,,, To install climate control seat air filter: • First, position the filter in it’s housing making sure that the far forward end is all the way up in the housing. Then push in on the center of the outside edge of the filter and rotate up into the housing until it clips into position.
Seating and safety restraints Push or pull the head rests to the desired position. Rear folding bench seat (if equipped) Folding down the rear seats Ensure that the headrest is in the down position and no objects such as books, purses or briefcases are on the floor in front of the second row seats before folding them down. Move front passenger seat forward so that the second row seat head rest clears the front seat. 1.
Seating and safety restraints Returning the seat to upright Always latch the vehicle seat to the floor, whether the seat is occupied or empty. If not latched, the seat may cause injury during a sudden stop. 1. Rotate the closeout panel onto the seatback and press the black control (adjacent to the green control) to lock. 2. Locate and lift the handle that reads “FOLD FLAT OR RECLINE”. 3. Pull on the seatback while lifting the handle to lift the seat into the upright position.
Seating and safety restraints the center seating position. For information on the proper operation of the safety restraints, refer to Safety Restraints in this chapter. The third row seat may be removed from the vehicle for additional cargo space. Accessing the third row seat Your vehicle is equipped with an easy entry second row seat feature which allows ready access to the third row seat.
Seating and safety restraints Removing the third row seat From the rear of the vehicle, with the liftgate open: 1. Disengage the lap/shoulder belt from the floor by inserting a key or small screwdriver through the hole in the boot of the detachable anchor. Then, press the release button to separate the detachable anchor from the anchor tongue. 2. Before removing the seat, be sure that the detachable anchor tongue is stowed flat into the vehicle floor. 3.
Seating and safety restraints • Pull the seat release lever located on the lower right side of the seatback while pushing the seatback down into the seat cushion. • The seatback will latch into place. 4. Lift the seat release bar located at the center of the seat near the floor to release the floor latches. 5. While pulling up on the release bar, lift the seat up and out of the floor tubs and roll seat rearward. 6. With assistance, lift the seat out of the vehicle.
Seating and safety restraints • When the rear of the seat is 10–13 cm (4–5 in) above the rear pins, let the seat drop. This will ensure that the seat will properly latch into the floor. 3. Locate the seat belt anchor tongue in the plastic housing on the floor. 4.
Seating and safety restraints 5. Lift latch up and out of floor tub to upright position using the strap on the latch. 6. Pull down support bar and push into floor latch. To return seat to seating position: 1. Hold seat and pull support bar from floor latch. 2. Rotate support bar up under seat. 3. Rotate floor latch down into floor tub. 4. Lower the seat. When the rear of the seat is 10–13 cm (4–5 in) above the rear pins, let the seat drop. This will ensure that the seat will properly latch into the floor.
Seating and safety restraints Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag SRS is provided. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Seating and safety restraints Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. To unfasten, push the release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts.
Seating and safety restraints When to use the automatic locking mode • Anytime a child safety seat is installed in a passenger front or outboard rear seating position (if equipped). Children 12 years old and under should be properly restrained in the rear seat whenever possible. Refer to Safety Restraints for Children or Safety Seats for Children later in this chapter. How to use the automatic locking mode • Buckle the combination lap and shoulder belt.
Seating and safety restraints How to disengage the automatic locking mode Ford recommends that all safety belt assemblies and attaching hardware should be inspected by a qualified technician after any collision. Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted.
Seating and safety restraints Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. To tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips. Shorten and fasten the belt when not in use. • 2nd row center seating position (if equipped) The lap belt will adjust automatically.
Seating and safety restraints Front and second row safety belt height adjustment Your vehicle has safety belt height adjustments for the driver, front passenger and second row passengers. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button down and slide the height adjuster down. To raise the height of the shoulder belt, slide the height adjuster up.
Seating and safety restraints Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... Then... The safety belt warning light illuminates1-2 minutes and the warning chime sounds 4-8 seconds. The safety belt warning light and warning chime turn off. The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding...
Seating and safety restraints The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... 9Crashes are rare events9 Consider... 36 700 crashes occur every day. The more we drive, the more we are exposed to 9rare9 events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our lifetime. 9I’m not going far9 3 of 4 fatal crashes occur within 25 miles of home.
Seating and safety restraints One time disable Anytime the safety belt is buckled and then unbuckled during an ignition ON cycle, Belt Minder will be disabled for that ignition cycle only. Deactivating/activating the belt minder feature Read steps 1 - 9 thoroughly before proceeding with the deactivation/activation programming procedure.
Seating and safety restraints 6. Within seven seconds of the safety belt warning light turning off, buckle then unbuckle the safety belt. • This will disable Belt Minder if it is currently enabled, or enable Belt Minder if it is currently disabled. 7. Confirmation of disabling Belt Minder is provided by flashing the safety belt warning light four times per second for three seconds. 8.
Seating and safety restraints AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Your vehicle is equipped with a crash sensing and diagnostic module which records information about the air bag and sensor systems. In the event of a collision this module may save information related to the collision including information about the air bag system and impact severity.
Seating and safety restraints Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. National Highway Traffic Safety Administration (NHTSA) recommends a minimum distance of at least 25 cm (10 inches) between an occupant’s chest and the driver air bag module. Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries.
Seating and safety restraints Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision. Air bags can kill or injure a child in a child seat.
Seating and safety restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the air bag. Small amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic.
Seating and safety restraints The RCM (restraints control module) monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors, the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors). Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system.
Seating and safety restraints Do not use accessory seat covers. The use of accessory seat covers may prevent the deployment of the side air bags and increase the risk of injury in an accident. Do not lean your head on the door. The side air bag could injure you as it deploys from the side of the seatback. Do not attempt to service, repair, or modify the air bag Supplemental Restraint System, its fuses or the seat cover on a seat containing an air bag. See your Ford or Lincoln Mercury dealer.
Seating and safety restraints by the collision will be inflated, even if the respective seat is not occupied. The air bag was designed to inflate between the door panel and occupant to further enhance the protection provided occupants in side impact collisions. The air bag SRS is designed to activate when the vehicle sustains lateral deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation.
Seating and safety restraints A difficulty with the system is indicated by one or more of the following: • The readiness light (same light as for front air bag system) will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on. • A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and light are repaired.
Seating and safety restraints Children and safety belts If the child is the proper size, restrain the child in a safety seat. Children who are too large for child safety seats (as specified by your child safety seat manufacturer) should always wear safety belts. Follow all the important safety restraint and air bag precautions that apply to adult passengers in your vehicle.
Seating and safety restraints Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision. When installing a child safety seat: • Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter.
Seating and safety restraints Carefully follow all of the manufacturer’s instructions included with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision. Installing child safety seats in combination lap and shoulder belt seating positions Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag.
Seating and safety restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it. 5.
Seating and safety restraints 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly tilt the seat forward and back to make sure the seat is securely held in place. 10.
Seating and safety restraints 5. If you have not pulled out enough webbing to reach, allow the webbing to fully retract before attempting to pull it out again and repeat steps 2 through 4. 6. Pull the webbing through the child seat toward the buckle while pushing down with your knee on the child seat. 7. Allow the safety belt to retract to remove any slack in the belt. It will make a clicking noise while doing this. 8.
Seating and safety restraints have a loop at the top, and are to be used for child seat tether anchorages. A tethered seat can be installed in the front passenger seat. Put the tether strap over the seatback and attach it to an anchor bracket. Anchor brackets can be bolted to the rear edge of the front passenger seat cushion. The bolt holes are in the bottom of the rear edge of the front passenger seat cushion frame. The anchor bracket must be installed using the instructions provided with the kit.
Seating and safety restraints The tether strap anchors in your vehicle are in the following positions (shown from top view): Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor. 1. Position the child safety seat on the seat cushion. 2. Route the child safety seat tether strap over the back of the seat. 3. Locate the correct anchor for the selected seating position.
Seating and safety restraints • You may need to pull the seatback forward to access the tether anchors. Make sure the seat is locked in the upright position before installing the child seat. Refer to the Folding Down The Rear Seats section in this chapter for information on how to operate the rear seats. 4. Clip the tether strap to the anchor as shown. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 5.
Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use the accelerator when you have difficulty starting the engine. For more information on starting the vehicle, refer to Starting the engine in this chapter.
Starting 2. Make sure the headlamps and vehicle accessories are off. 3. Make sure the gearshift is in P (Park). 4. Make sure the parking brake is set. HOOD BRAKE 5. Turn the key to 4 (ON) without turning the key to 5 (START). 4 If there is difficulty in turning the 3 key, firmly rotate the steering wheel 5 left and right until the key turns freely.
Starting DOOR AJAR H 60 40 L 80 00 F E H NAVIGATOR 4X4 20 L 40 20 LOW FUEL SERVICE ENGINE SOON THEFT LOW RANGE 60 MPH H RPMX1000 km/h D 2 P RN D SELECT RESET CK SUSP C BRAKE Make sure the corresponding lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. STARTING THE ENGINE 1.
Starting Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater-defroster system to respond quickly. Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below. For best results, plug the heater in at least three hours before starting the vehicle.
Starting Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air. Improve vehicle ventilation by keeping all air inlet vents clear of snow, leaves and other debris.
Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Driving ABS warning lamp ABS The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal BRAKE braking is still effective unless the ! brake warning light also remains illuminated with parking brake released.
Driving Parking brake with auto-release Apply the parking brake whenever the vehicle is parked. To set the parking brake, press the parking brake pedal down until the pedal stops. HOOD BRAKE The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. BRAKE ! Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park).
Driving If the parking brake fails to release after completing this procedure, use the manual parking brake release lever. Pull the release lever to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy. HOOD BRAKE STEERING Your vehicle is equipped with power steering. Power steering uses energy from the engine to help steer the vehicle.
Driving Speed sensitive steering The steering in your vehicle is speed sensitive. At high speeds, steering assist will decrease to improve steering feel. At lower speeds, maneuverability will be increased. If the amount of effort required to steer your vehicle changes while driving at a constant vehicle speed, have the power steering system checked by your dealer or a qualified service technician.
Driving The air suspension shut-off switch is located behind an access panel underneath the passenger side instrument panel. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Normal vehicle operation does not require any action by the driver.
Driving To avoid injury, never run the engine with one wheel off the ground, such as when changing a tire. PREPARING TO DRIVE YOUR VEHICLE Utility vehicles have a significantly higher rollover rate than other types of vehicles. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Your vehicle has special design and equipment features to make it capable of performing in a wide variety of circumstances.
Driving AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the brake pedal depressed: 1. Apply the parking brake, turn ignition key to LOCK, then remove the key. 2. Insert the key and turn it to OFF.
Driving Driving with a 4–speed automatic transmission Your vehicle’s automatic transmission is equipped with a special shift strategy that insures maximum heater performance during cold weather operation. When ambient temperature is –5° C (23° F) or below and the engine coolant temperature is below 38° C (100° F), light throttle upshifts may be slightly delayed. Once the engine coolant temperature reaches 71° C (160° F) the normal shift strategy will resume.
Driving R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this gear. (Overdrive) The normal driving position for the best fuel economy. Transmission operates in gears one through four.
Driving Each time the vehicle is started, the transmission will automatically return to normal overdrive mode. Every time the vehicle is shut off and restarted, you must press the transmission control switch to cancel overdrive operation if driving in overdrive is not desired. 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades.
Driving FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this chapter. When Four–wheel drive (4WD) is engaged, power is supplied to all four wheels through a transfer case. 4WD power can be selected when additional driving power is desired.
Driving Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns or abrupt maneuvers in these vehicles. Using the Control-Trac system Shifting from A4WD to 4H Move the 4WD control from A4WD to 4H at any forward speed up to 88 km/h (55 mph).
Driving Shifting to A4WD Move the 4WD control back to A4WD at a stop or at speeds up to 88 km/h (55 mph). A4WD 4H 4L Driving off-road with 4WD Your vehicle is specially equipped for driving on sand, snow, mud and rough terrain and has operating characteristics that are somewhat different from conventional vehicles, both on and off the road. Maintain steering wheel control at all times, especially in rough terrain.
Driving Do not spin the wheels at over 56 km/h (35 mph). The tires may fail and injure a passenger or bystander. Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. Do not reduce the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels. Mud and water If you must drive through high water, drive slowly. Traction or brake capability may be limited.
Driving reduces strain on the engine and the possibility of stalling. When descending a steep hill, avoid sudden braking. Shift to a lower gear when added engine braking is desired. When speed control is on and you are driving uphill, your vehicle speed may drop considerably, especially if you are carrying a heavy load. If vehicle speed drops more than 16 km/h (10 mph), the speed control will cancel automatically. Resume speed with accelerator pedal.
Driving Driving through deep water where the transmission vent tube is submerged may allow water into the transmission and cause internal transmission damage. VEHICLE LOADING Before loading a vehicle, familiarize yourself with the following terms: • Base Curb Weight: Weight of the vehicle including any standard equipment, fluids, lubricants, etc. It does not include passengers or aftermarket equipment. • Payload: Combined maximum allowable weight of cargo, passengers and optional equipment.
Driving Remember to figure in the tongue load of your loaded trailer when figuring the total weight. Do not exceed the GVWR or the GAWR specified on the certification label. Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher limit than the originals do not increase the GVWR and GAWR limitations.
Driving Calculating the load your vehicle can carry/tow 1. Use the appropriate maximum gross combined weight rating (GCWR) chart to find the maximum GCWR for your type engine and rear axle ratio. 2. Weigh your vehicle as you customarily operate the vehicle without cargo. To obtain correct weights, try taking your vehicle to a shipping company or an inspection station for trucks. 3. Subtract your loaded vehicle weight from the maximum GCWR on the following charts.
Driving GCWR (Gross Combined Weight Rating)/Trailer weights Rear axle Maximum GCWR Trailer weight range Engine ratio kg (lbs.) (0-maximum) - kg (lbs.) 4x2 with 17 inch wheels 6 577 0-4 037 5.4L-4V 3.73 (14 500) (0-8 900) 4x4 with 17 inch wheels 6 350 0-3 674 5.4L-4V 3.73 (14 000) (0-8 100) Maximum frontal area of trailer is 5.6 square meters (60 square feet) Do not exceed the maximum loads listed on the Safety Compliance Certification label.
Driving Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of control and personal injury. Preparing to tow Use the proper equipment for towing a trailer, and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance. Hitches Do not use hitches that clamp onto the vehicle’s bumper or attach to the axle.
Driving If you use a rental trailer, follow the instructions that the rental agency gives to you. Do not attach safety chains to the bumper. Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes are safe if installed properly and adjusted to the manufacturer’s specifications. The trailer brakes must meet local and Federal regulations. Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system.
Driving Recreational towing (all wheels on the ground) An example of recreational towing would be towing your vehicle behind a Motorhome. Follow these guidelines if you have the need for recreational towing your vehicle with all four wheels on the ground. These guidelines are designed to ensure that your transmission is not damaged.
Driving Launching or retrieving a boat When backing down a ramp during boat launching or retrieval, • Do not allow the static water level to rise above the bottom edge of the rear bumper and • Do not allow waves to break higher than 15 cm (6 inches) above the bottom edge of the rear bumper. Exceeding these limits may allow water to enter critical vehicle components, adversely affecting driveability, emissions, reliability and causing internal transmission damage.
Roadside emergencies GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the Basic warranty period (Canada) or New Vehicle Limited Warranty period (U.S.
Roadside emergencies Roadside coverage beyond basic warranty In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer. Similarly in Canada, you may purchase additional coverage beyond the basic coverage period by consulting the Ford Roadside Assistance Club brochure or by calling 1–877–294–CLUB (1–877–894–2582).
Roadside emergencies The fuel pump shut-off switch is located in the passenger’s foot well, by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. Turn the ignition to the ON position. Pause for a few seconds and return the key to the OFF position. 5.
Roadside emergencies Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color COLOR Fuse Rating Mini Fuses Standard Fuses Maxi Fuses 2A 3A 4A 5A 7.
Roadside emergencies 20 21 10 11 31 30 9 RELAY 5 29 19 8 28 18 27 17 7 RELAY 4 RELAY 3 RELAY 2 RELAY 1 6 16 5 26 15 4 25 14 13 2 3 12 FUSE1 22 23 24 To remove a fuse use the fuse puller tool provided on the fuse panel cover. The fuses are coded as follows.
Roadside emergencies Fuse/Relay Location 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 162 Fuse Amp Passenger Compartment Rating Fuse Panel Description 5A Cluster, Overhead Trip Computer, Compass, Steering Sensor, Brake Shift Interlock Solenoid, Air Suspension Module, GEM Module, Heated Mirror, Rear Defroster, Reverse Sensing System, Automatic Park Brake Release 5A Aux A/C Blower Relay, Console Blower 5A Remote Entry Module, Cell Phone, Clock, GEM Module, Navigation — Not Used — Not Used 30A Front Washer Pu
Roadside emergencies Fuse/Relay Location 21 22 23 24 25 26 27 28 29 30 31 Relay Relay Relay Relay Relay 1 2 3 4 5 Fuse Amp Passenger Compartment Rating Fuse Panel Description 15A Starter Relay, Fuse 20, Digital Transmission Range Selector 10A Air Bag Module, EATC, EATC Blower Relay, Feeds Fuse 7 10A Electrochromic Mirror, Aux A/C, Heated Seats, Trailer Tow Battery Charge, Turn/Hazard Flasher, Console Blower Door Actuator, 4x4 Clutch Relay, 4 Wheel Anti-Lock Brake System (4WABS) Module — Not Used — Not Us
FUSE 1 FUSE 2 FUSE 3 FUSE 4 FUSE 5 FUSE 6 FUSE 7 FUSE 8 FUSE 9 FUSE 10 FUSE 11 FUSE 12 FUSE 13 FUSE 14 FUSE 15 FUSE 16 FUSE 17 FUSE 18 FULL RELAY 301 MAXI FUSE 108 MAXI FUSE 107 MAXI FUSE 104 MAXI FUSE 112 MAXI FUSE 111 MAXI FUSE 103 MAXI FUSE 116 HALF RELAY 202 MAXI FUSE 102 MAXI FUSE 101 MAXI FUSE 110 MAXI FUSE 114 MAXI FUSE 118 MAXI FUSE 106 CB602 HALF RELAY 204 HALF RELAY 206 HALF RELAY 209 MAXI FUSE 105 MAXI FUSE 109 MAXI FUSE 113 D 503 FULL RELAY 304 D 502 HALF REL
Roadside emergencies The high-current fuses are coded as follows: Fuse/Relay Location 1 2 3 4 5 6 Fuse Amp Rating 20A * 30A* 30A* 20A* 20A* 15A* 7 8 9 10 11 12 13 14 15 16 17 18 20A* 30A* 15A* 20A* 20A* 10A* 15A* — 10A* — 10A* 15A* 19 20 21 22 23 10A* 10A* — — 15A* 24 101 102 103 — 30A** 50A** 50A** Power Distribution Box Description Power Point Powertrain Control Module Headlamps/Autolamps Console Powerpoint Trailer Tow Backup/Park Lamps Parklamps/Autolamps, Feeds Passenger Compartment Fuse 18 Horn
Roadside emergencies Fuse/Relay Location 104 105 106 107 Fuse Amp Rating 30A** 40A** — 30A** 108 109 110 111 30A** 50A** 30A** 40A** 112 30A** 113 40A** 114 115 116 117 118 201 202 203 204 205 206 207 208 209 301 302 303 30A** — 40A** — — — — — — — — — — — — — — 166 Power Distribution Box Description 4x4 Shift Motor & Clutch Climate Control Front Blower Not Used Passenger Power Seat, Passenger Seat Lumbar Trailer Tow Electric Brake Air Suspension Compressor Heated Seats/CCS Ignition Switch Batter
Roadside emergencies Fuse/Relay Location 304 401 501 502 503 601 Fuse Amp Rating — — — — — 30A 602 — *Mini fuses **Maxi fuses Power Distribution Box Description Powertrain Control Module Relay Not Used Powertrain Control Module Diode A/C Clutch Diode Automatic Park Brake Release Diode Delayed Accessory (Power Windows, Flip Windows, Radio, Moonroof) Not Used Relays Relays are located in the power distribution box and should be replaced by qualified technicians.
Roadside emergencies Removing the jack handle 1. Open the hood. 2. Unsnap the end of the handle that is retained by the clip on the top of the windshield washer bottle. 3. Unsnap the shaft of the handle from the two retaining clips attached to the top of the radiator shroud. Removing the jack and tools 1. Locate the access panel on the right rear quarter panel interior trim. Lift the two panel retaining clips and remove the panel. 2.
Roadside emergencies Stowing the spare tire 1. Lay the tire on the ground with the outboard side facing up. 2. Install the retainer through the wheel center and slide the wheel under the vehicle. 3. Turn the spare handle clockwise until the tire is raised to its original position underneath the vehicle. The spare handle ratchets when the tire is raised to the stowed position. It will not allow you to overtighten.
Roadside emergencies 1. Park on a level surface, activate hazard flashers and set the parking brake. 2. Place gearshift lever in P (Park) and turn engine OFF. HOOD BRAKE 3. Block the diagonally opposite wheel. 4. Obtain the spare tire and jack from their storage locations. 5. Use the tip of the lug wrench to remove any wheel trim. 6. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground.
Roadside emergencies 7. Turn OFF the air suspension switch. 8. Position the jack according to the following guides and turn the jack handle clockwise until the wheel is completely off the ground. When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the transmission is in P (Park).
Roadside emergencies • Front (4x4) • Rear To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. • Never use the front or rear differential as a jacking point. 9. Remove the lug nuts with the lug wrench. 10. Replace the flat tire with the spare tire, making sure the valve stem is facing outward.
Roadside emergencies 12. Remove the jack and fully tighten the lug nuts in the order shown. 13. Stow the flat tire. Refer to Stowing the spare tire. 14. Stow the jack and lug wrench. Make sure the jack is fastened so it does not rattle when you drive. 15. Unblock the wheels. 16. Turn on the air suspension switch. 1 3 4 5 2 JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage.
Roadside emergencies 3. Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts. 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect any electrical surges. Turn all other accessories off.
Roadside emergencies + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. + + – – 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.
Roadside emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables + + – – Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface.
Roadside emergencies + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. If equipped with air suspension, the air suspension control must be turned to the OFF position.
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service. Check your “Warranty Guide” to find out which parts and services are covered.
Maintenance and care Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. HOOD BRAKE 2. Go to the front of the vehicle and release the auxiliary latch located under the front of the hood, just above the passenger side headlamp. Slide the yellow handle to release the auxiliary latch. 3.
Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 5.4L 4V V8 engine 1 2 3 4 5 6 7 8 10 9 1. Battery 2. Automatic transmission fluid dipstick 3. Engine oil filler cap 4. Power steering fluid reservoir 5. Engine oil dipstick 6. Brake fluid reservoir 7. Power distribution box 8. Air filter assembly 9. Engine coolant reservoir 10.
Maintenance and care 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). MIN MAX 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL.
Maintenance and care • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity.
Maintenance and care Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by your warranty. Change your engine oil and filter according to the appropriate schedule listed in the scheduled maintenance guide. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life.
Maintenance and care If you use a brake fluid that is not DOT 3, you will cause permanent damage to your brakes. Do not let the fluid level in the reservoir for the master cylinder fall below the MIN mark. If master cylinder runs dry, this may cause the brakes to fail. WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low, add enough fluid to fill the reservoir.
Maintenance and care ENGINE COOLANT Checking engine coolant Your engine’s cooling system has been factory-filled with a 50/50 mixture of distilled water and Ford G05 Engine Coolant (yellow in color) per ford specification WSS-M97B51–A1. A 50/50 mixture of distilled water and Ford G05 Engine Coolant provides: • maximum cooling system efficiency. • freeze protection down to -36° C (-34° F). • boiling protection up to 129° C (265° F). • protection against rust and other forms of corrosion.
Maintenance and care • Refer to the scheduled maintenance guide for service interval schedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter. If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become low or empty. If the reservoir is low or empty, add engine coolant to the reservoir. Refer to Adding engine coolant in this chapter.
Maintenance and care Do not put engine coolant in the windshield washer fluid reservoir. If engine coolant is sprayed onto the windshield, it could make it difficult to see through the windshield. When the engine is cool, add a 50/50 mixture of engine coolant and distilled water to the engine coolant reservoir, until the coolant is at the “cold fill level” or within the “cold fill range” as listed in the engine coolant reservoir (depending upon application).
Maintenance and care Recycled engine coolant Ford Motor Company recommends the use of a recycled engine coolant produced by Ford-approved processes. Not all coolant recycling processes produce coolant which meets Ford specification ESE-M97B44-A. Use of a recycled engine coolant which does not meet the Ford specification may harm engine and cooling system components. Always dispose of used automotive fluids in a responsible manner.
Maintenance and care • decreased engine coolant concentrations below 40% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage. • refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive. Vehicles driven year-round in non-extreme climates should use a 50/50 mixture of engine coolant and distilled water for optimum cooling system and engine protection.
Maintenance and care Once the engine temperature cools, the engine can be re-started. Take your vehicle to a service facility as soon as possible to minimize engine damage. When fail-safe mode is activated You have limited engine power when in the fail-safe mode, so drive the vehicle with caution. The vehicle will not be able to maintain high speed operation and the engine will run rough. Remember that the engine is capable of completely shutting down automatically to prevent engine damage, therefore: 1.
Maintenance and care 4. Check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is in this range. 5. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and MAX lines. Be sure to put the cap back on the reservoir.
Maintenance and care 5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary, refer to Identifying components in the engine compartment in this chapter for the location of the dipstick. 6. Install the dipstick making sure it is fully seated in the filler tube. 7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated area for normal operating temperature or ambient temperature.
Maintenance and care Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type of fluid used is normally indicated on the dipstick and also in the Lubricant specifications section in the Capacities and specifications chapter. Use of a non-approved automatic transmission fluid may cause internal transmission component damage. If necessary, add fluid in 250 mL (1/2 pint) increments through the filler tube until the level is correct.
Maintenance and care If the electrolyte level in the battery is low, you can add plain tap water to the battery, as long as you do not use hard water (water with a high mineral or alkali content). If possible, however, try to only fill the battery cells with distilled water. If the battery needs water often, have the charging system checked. If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced.
Maintenance and care Battery posts, terminals and related accessories contain lead and lead compunds. Wash hands after handling. RN LE TU AD RE Because your vehicle’s engine is electronically controlled by a computer, some control conditions are maintained by power from the battery. When the battery is disconnected or a new battery is installed, the engine must relearn its idle and fuel trim strategy for optimum driveability and performance. To begin this process: 1.
Maintenance and care AIR FILTER MAINTENANCE Refer to the scheduled maintenance guide for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the Motorcraft air filter element listed. Refer to Motorcraft Part Numbers in the Capacities and specifications chapter. Do not start your engine with the air cleaner removed and do not remove it while the engine is running. Changing the air filter element 1.
Maintenance and care 3. Remove the air filter element from the air filter housing. 4. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover. This could cause filter damage and allow unmetered air to enter the engine if not properly seated. 5. Replace the air filter cover and secure the clamp. 6. Replace the air inlet tube and secure the clamp.
Maintenance and care Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 3. Attach the new wiper to the wiper arm and press it into place until a click is heard.
Maintenance and care U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
Maintenance and care The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles).
Maintenance and care Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity. Use only the tire combinations recommended on the label. If you do not follow these precautions, your vehicle may not drive properly and safely.
Maintenance and care The tires on your vehicle have all weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires and chains. Follow these guidelines when using snow tires and chains: • Use only cable type chains offered by Ford as an accessory or equivalent. SAE class “S” or other conventional link type chains may contact and cause damage to the vehicle’s wheel house and/or body.
Maintenance and care Automotive fuels can cause serious injury or death if misused or mishandled. Gasoline may contain benzene, which is a cancer-causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury.
Maintenance and care splashed on the skin, promptly wash skin thoroughly with soap and water. Consult a physician immediately if you experience an adverse reaction. When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be taken to avoid inhaling excess fumes.
Maintenance and care octane ratings may degrade performance. We do not recommend the use of gasolines labeled as “Premium” in high altitude areas that are sold with octane ratings of less than 91. Do not be concerned if your engine sometimes knocks lightly. However, if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating, see your dealer or a qualified service technician to prevent any engine damage.
Maintenance and care Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine. • Your “Service Engine Soon” indicator may come on. For more information on the “Service Engine Soon” indicator, refer to the Instrumentation chapter.
Maintenance and care If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury. Fuel Filter For fuel filter replacement, see your dealer or a qualified service technician. Refer to the scheduled maintenance guide for the appropriate intervals for changing the fuel filter. Replace the fuel filter with an authorized Motorcraft part.
Maintenance and care For consistent results when filling the fuel tank: • Use the same filling rate setting (low — medium — high) each time the tank is filled. • Allow three automatic click-offs when filling (more than three clicks would overfill the tank). • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump and have the vehicle facing the same direction each time you fill up.
Maintenance and care Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy. • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel economy. • Slow down gradually. • Driving at reasonable speeds (traveling at 88 km/h [55 mph] uses 15% less fuel than traveling at 105 km/h [65 mph]).
Maintenance and care • Carrying unnecessary weight may reduce fuel economy (approximately 0.4 km/L [1 mpg] is lost for every 180 kg [400 lb] of weight carried). • Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy. • Using fuel blended with alcohol may lower fuel economy. • Fuel economy may decrease with lower temperatures during the first 12–16 km (8–10 miles) of driving.
Maintenance and care • Have the items listed in your scheduled maintenance guide performed according to the specified schedule. The scheduled maintenance items listed in the scheduled maintenance guide are essential to the life and performance of your vehicle and to its emissions system.
Maintenance and care If the vehicle’s powertrain system or its battery has just been serviced, the on-board diagnostics system is reset to a “not ready for I/M test” condition. To ready the on-board diagnostics system for I/M testing, a minimum of 30 minutes of city and highway driving is necessary as described below: • First, at least 10 minutes of driving on an expressway or highway. • Next, at least 20 minutes driving in stop-and-go, city-type traffic with at least four idle periods.
Maintenance and care 3. At the back of the headlamp, remove the headlamp assembly retainers by pushing rearward and pulling up. 4. Pull the headlamp assembly forward slightly to expose the electrical connectors. 5. Rotate the bulb cover counterclockwise and remove. 6. Disconnect the electrical connector from the bulb by pulling rearward. 7. Remove the bulb retainer ring by turning it counterclockwise, then slide the ring off the plastic base.
Maintenance and care 8. Without turning, carefully pull the bulb out of the headlamp assembly. Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. 9. Insert the glass end of the new bulb into the headlamp assembly.
Maintenance and care 5. Release clip and disconnect the electrical connector from the bulb socket. 6. Rotate the bulb socket counterclockwise and remove. 7. Pull the bulb straight out of the socket and push in the new bulb. 8. To complete installation of the parking lamp/turn signal assembly, follow the removal procedures in reverse order. Replacing foglamp bulbs The halogen bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped.
Maintenance and care Replacing tail lamp bulbs 1. Open the liftgate to expose the lamp assembly screws. 2. Remove the two screws from the lamp assembly. 3. Carefully pry the lamp assembly away from the vehicle to expose the bulb socket. 4. Rotate the bulb socket counterclockwise and remove from lamp assembly. 5. Pull bulb straight out of socket and push in the new bulb. 6. Install the bulb socket into the lamp assembly and rotate clockwise. 7.
Maintenance and care 3. Rotate the bulb socket counterclockwise counterclockwise and remove. 4. Pull bulb straight out of socket and push in the new bulb. 5. To complete installation, follow the removal procedure in reverse order. Replacing license plate lamp bulbs To change the license plate bulbs: 1. Remove screw and the license plate lamp assembly from liftgate. 2. Remove the bulb socket from lamp assembly by turning counterclockwise. 3.
Maintenance and care Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to assure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.
Maintenance and care AIMING THE HEADLAMPS Your vehicle is equipped with a Vehicle Headlamp Aim Device (VHAD) on each headlamp. Each headlamp may be properly aimed in the vertical (up/down) and the horizontal (left/right) directions using your VHAD system. The headlamps on your vehicle are properly aimed at the assembly plant. A bubble (vertical indicator) that is not centered between the two red lines does not necessarily indicate out-of-aim headlamps.
Maintenance and care Turning the horizontal adjusting screw in the direction of the arrow changes the horizontal aim as shown. Vertical aim adjustment 1. Park the vehicle on a level surface. 2. With the hood open, locate the bubble level and the vertical adjustment screw. The adjustment screw is located on the outboard side of the headlamp. U D U 3. The “U” and “D” on the bubble indicate the directional change (up or down) of the vertical aim. 4.
Maintenance and care CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance chapter for a list of Ford-approved cleaners, polishes and waxes. Washing your vehicle Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap. If your vehicle is particularly dirty, use a quality car wash detergent. Always use a clean sponge, washing glove or similar device and plenty of water for best results.
Maintenance and care recommended that you clean the wiper blades and windshield as described in Cleaning the wiper blades and windshield. Repairing paint chips Minor scratches or paint damage from road debris may be repaired with the Ultra Touch Prep and Finishing Kit (#F7AZ-19K507–BA), Lacquer Touch-up Paint (#ALBZ-19500–XXXXA), or Exterior Acrylic Spray Lacquer (#ALAZ-19500–XXXXA) from the Ford Car Care Chemicals line.
Maintenance and care • Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning non-painted plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary. Do not clean plastic parts with thinners, solvents or petroleum-based cleaners. Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle.
Maintenance and care hot wax treatments used by commercial car washes. Clean the outside of the windshield or rear window with a non-abrasive cleaner such as Ford Ultra-Clear Spray Glass Cleaner, (E4AZ-19C507–AA), available from your Ford Dealer. Do not use abrasive cleansers on glass as they may cause scratches. The windshield or rear window is clean if beads do not form when you rinse it with water.
Maintenance and care the Deluxe Leather Care Kit F8AZ-19G253–AA, which is available from your Ford Dealer. This mild cleaner and special pad, cleans the leather and maintains its natural beauty. Follow the instructions on the cleaner label. Regular cleaning of your leather upholstery helps maintain its resiliency and color. Do not use household cleaning products, alcohol solutions, solvents or cleaners intended for rubber, vinyl or plastics.
Capacities and specifications MOTORCRAFT PART NUMBERS Component Air filter element Battery (standard) Fuel filter Oil filter PCV valve Spark plugs* 5.4L 4V V8 engine FA-1634 BXT-65-650 FG-986B FL-820-S EV-233 AWSF-32P * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information.
Capacities and specifications Fluid Engine coolant Front axle lubricant Rear axle lubricant 4 Windshield washer fluid 1 3 Ford Part Application Name Premium Engine without aux rear Coolant heat with aux rear heat Motorcraft SAE 4 x 4 vehicles 75W-90 Premium 4x4 Front Axle Lubricant Motorcraft SAE All 75W-140 Synthetic Rear Axle Lubricant Ultra-Clear All Windshield Washer Concentrate Capacity 24.1L (25.5 quarts) 26.4L (27.9 quarts) 1.8-2.0L (3.5-3.7 pints) 2.9-3.1L (5.5-5.8 pints) 4.1L (4.
Capacities and specifications amount of transmission fluid and fluid level should be set by the indication on the dipstick’s normal operating range. 3 Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter. 4 Your vehicle’s rear axle is filled with a synthetic rear axle lubricant and is considered lubricated for life.
Capacities and specifications Item Engine coolant Engine oil Ford part name Ford Premium Engine Coolant Ford part number E2FZ-19549-AA (in Canada, Motorcraft CXC-10) XO-5W-30-QSP Motorcraft SAE 5W-30 Super Premium Motor Oil E8TZ-19590-A 4x4 front wheel High bearings, 4x4 Temperature 4x4 Front Axle spindle needle bearings, spindle & Wheel Bearing thrust bearings Grease & front drive axle u-joint/slip spline Motorcraft XT-2-QDX Automatic MERCONt ATF transmission 1 Power steering Motorcraft XT-2-QDX fluid
Capacities and specifications Item Windshield washer fluid Ford part name Ultra-clear Windshield Washer Concentrate Ford part number C9AZ-19550-AC Ford specification ESR-M17P5-A 1 Ensure the correct automatic transmission fluid is used. Transmission fluid requirements are indicated on the dipstick or on the dipstick handle. Check the container to verify the fluid being added is of the correct type. Refer to your scheduled maintenance guide to determine the correct service interval.
Capacities and specifications ENGINE DATA Engine Cubic inches Required fuel Firing order Spark plug gap Ignition system Compression ratio 5.4L 4V V8 engine 330 91 octane 1-3-7-2-6-5-4-8 1.3-1.4 mm (0.052-0.056 inch) Coil on plug 9.5:1 VEHICLE DIMENSIONS Vehicle dimensions 4x2 mm (in) (1) Overall length 5 202.0 (204.8) (2) Vehicle width 2 027.0 (79.8)1 2 (3) Overall height 1 907.0 (75.1) (4) Wheelbase 3 026.0 (119.1) (5) Track - Front 1 661.0 (65.4) (5) Track - Rear 1 663.0 (65.5) 1 2 4x4 mm (in) 5 202.
Capacities and specifications 4 1 3 5 2 233
Capacities and specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’s side. MFD. BY FORD MOTOR CO. IN U.S.A.
Customer assistance Ford Extended Service Plan You can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.S.) and Ford of Canada (in Canada).
Customer assistance If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing dealership. 2. If your inquiry or concern remains unresolved, contact the Sales Manager or Service Manager at the dealership. 3. If the inquiry or concern cannot be resolved at the dealership level, please contact the Ford Customer Assistance Center.
Customer assistance If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Assistance Center to find an authorized dealership to help you. In the United States: Ford Motor Company Customer Assistance Center 16800 Executive Plaza Drive P.O.
Customer assistance replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson-Moss Warranty Act or state replacement or repurchase laws. THE DISPUTE SETTLEMENT BOARD (U.S.
Customer assistance Concerns are ineligible for review if the New Vehicle Limited Warranty has expired at receipt of your application and, in certain states eligibility is dependent upon the customer’s possession of the vehicle. Eligibility may differ according to state law. For example, see the unique brochures for California, West Virginia, Georgia and Wisconsin purchasers/lessees.
Customer assistance • a brief summary of the action taken by the dealer(s) and Ford Motor Company • the names (if known) of all the people you contacted at the dealership(s) • a description of the action you expect to resolve your concern You will receive a letter of explanation if your application does not qualify for Board review. Oral presentations If you would like to make an oral presentation, indicate YES to question #6 on the application.
Customer assistance You may also contact the North American Customer Assistance Center at 1-800-392-3673 (Ford), TDD for the hearing impaired: 1-800-232-5952 or by writing to the Center at the following address: Ford Motor Company Customer Assistance Center 16800 Executive Plaza Drive P.O.
Customer assistance The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company/Ford of Canada is not responsible for any damage caused by use of improper fuel. In the United States, using leaded fuel may also result in difficulty importing your vehicle back into the U.S.
Customer assistance Ford Deluxe Leather and Vinyl Cleaner (not available in Canada) Motorcraft Vinyl Cleaner (Canada only) Ford Extra Strength Tar and Road Oil Remover* (not available in Canada) Ford Extra Strength Upholstery Cleaner (Canada only) Ford Extra Strength Upholstery Cleaner (not available in Canada) Ford Metal Surface Cleaner Ford Multi-Purpose Cleaner* Motorcraft Car Wash Concentrate Motorcraft Carlite Glass Cleaner Ford Spot and Stain Remover* Ford Super Premium Tire and Trim Dressing Ford Tri
Customer assistance Comfort and convenience Cabin air filter Cargo nets (Floor mount) Cargo organizers Cargo trays Engine block heaters Tire step Travel equipment Ashtray, rear seat Automatic headlamp system with DRL Daytime running lights (DRL) Factory luggage rack Factory luggage rack adaptors Heavy-duty battery Raised cross bars Raised cross bar adaptors Towing mirrors (removable and permanent) Trailer hitch bars and balls Trailer hitch mounted bike carrier Trailer hitch wiring adaptor Protection and app
Customer assistance Lubricants and oils Molded vinyl floor mats Rear air deflectors Side window air deflectors Spare tire lock Touch-up paint Universal floor mats For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR or GAWR as indicated on the Safety compliance certifica
Customer assistance ORDERING ADDITIONAL OWNER’S LITERATURE To order the publications in this portfolio: Make checks payable to: HELM, INCORPORATED P.O. Box 07150 Detroit, Michigan 48207 For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST, for credit card holders only Obtaining a French owner’s guide French Owner’s Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P.O.
Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Index A Accessory delay ..........................72 Air bag supplemental restraint system ................111, 115 and child safety seats ............113 description ......................111, 115 disposal ............................115, 118 driver air bag ..................113, 116 indicator light .............9, 115, 117 operation .........................113, 116 passenger air bag ...........113, 116 side air bag ..............................115 Air cleaner filter ...............
Index Cellular telephone (see your Cellular Phone Guide) ................75 Certification Label ....................234 Child safety restraints ..............119 child safety belts ....................119 Child safety seats ..............119–120 attaching with tether straps ..124 in front seat ............................121 in rear seat ..............121, 123–124 Cleaning your vehicle ...............222 engine compartment ..............223 exterior ....................................223 exterior lamps ...
Index through water .................146–148 E Emergencies, roadside jump-starting ..........................173 Emission control system ..........211 Engine ........................................232 check engine/ service engine soon light ...........8 cleaning ...................................223 coolant .....................................186 fail-safe coolant ......................190 idle speed control ...................194 lubrication specifications ..................229, 232 refill capacities ..
Index engine coolant temperature gauge ...................14 engine oil pressure gauge ........16 fuel gauge ..................................13 odometer ...................................15 speedometer .............................14 tachometer ................................15 trip odometer ............................15 GAWR (Gross Axle Weight Rating) .....149 calculating ...............................151 definition .................................149 driving with a heavy load ......149 location ...
Index headlamps, flash to pass ..........18 instrument panel, dimming .....19 interior lamps ...................66, 219 replacing bulbs .......213, 215–218 Lane change indicator (see Turn signal) ........................53 Liftgate ........................................76 Lights, warning and indicator ......8 air bag ..........................................9 air suspension .........................138 anti-lock brakes (ABS) ....10, 134 anti-theft ...................................11 brake .............
Index fluid, specifications .........229, 232 Preparing to drive your vehicle .....................139 R Radio ............................................25 Relays ................................159, 167 Remote entry system ...........79–80 illuminated entry ......................83 locking/unlocking doors ...........80 panic alarm ...............................80 replacement/additional transmitters ...............................82 replacing the batteries .............81 Reverse sensing system .........
Index recreational towing .................155 trailer towing ..........................151 wrecker ....................................178 Traction-lok rear axle ...............138 Transmission .............................140 fluid, checking and adding (automatic) .............................192 fluid, refill capacities ..............227 lubricant specifications ..229, 232 Trip odometer .............................15 Turn signal ............................10, 53 V Vehicle dimensions ...................
Filling station information Item Required fuel-5.4L 4V V8 engine Fuel tank capacity Tire size and pressure Information Unleaded fuel only - 91 octane 113.6L (30 gallons) Refer to the Certification Label inside of driver’s door. Hood release Pull handle under the left side of the instrument panel. Engine oil capacity (includes filter 5.7L (6.0 quarts). Use Motorcraft change) SAE 5W-30 Super Premium Motor Oil, Ford specification WSS-M2C153-G. 24.1L (25.
Filling station information an automatic transmission application requiring MERCONt may cause transmission damage. Use of any fluid other than the recommended fluid may cause transmission damage. 3 Indicates only approximate dry-fill capacity. Some applications may vary based on cooler size and if equipped with in-tank cooler. The amount of transmission fluid and fluid level should be set by the indication on the dipstick’s normal operating range.
