Table of Contents Introduction Congratulations Safety and environment protection Symbol glossary Instrument Cluster 4 4 5 8 10 Warning and control lights Gauges 10 17 Entertainment Systems 19 AM/FM stereo cassette AM/FM stereo cassette (CD changer compatible) CD changer Climate Controls Electronic automatic temperature control Lights Headlamps Bulb replacement Driver Controls Steering wheel adjustment Power windows Mirrors Message center 19 26 38 43 43 49 49 53 59 60 62 63 77 Locks and Secur
Table of Contents Seating and Safety Restraints Seating Safety restraints Air bags Child restraints Driving Starting Brakes Traction control/AdvanceTrac Transmission operation Vehicle loading Trailer towing Recreational towing Roadside Emergencies 102 106 121 128 136 136 140 143 146 150 151 154 156 Hazard flasher switch Fuses and relays Changing tires Jump starting Wrecker towing 157 158 165 169 175 Customer Assistance 176 The dispute settlement board Utilizing the mediation/arbitration Getting as
Table of Contents Maintenance and Specifications Hood Engine compartment Engine oil Battery Fuel information Air filter(s) Refill capacities Lubricant specifications Engine data Vehicle dimensions 193 194 194 195 199 207 221 227 228 230 230 Accessories 234 Index 237 All rights reserved.
Introduction The following warning may be required by California law: CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction Fuel pump shut-off switch In the event of an accident the safety switch will automatically cut off the fuel supply to the engine. The switch can also be activated through sudden vibration (e.g. collision when parking). To reset the switch, refer to the Fuel pump shut-off switch in the Roadside emergencies chapter.
Introduction BREAKING-IN YOUR VEHICLE There are no particular guidelines for breaking-in your vehicle. During the first 1 600 km (1 000 miles) of driving, vary speeds frequently. This is recommended to give the moving parts a chance to break in. SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper-to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 7.3L Power Stroke Diesel Engine Coverage.
Introduction MIDDLE EAST/NORTH AFRICA VEHICLE SPECIFIC INFORMATION For your particular global region, your vehicle may be equipped with features and options that are different from the ones that are described in this Owner Guide; therefore, a supplement has been supplied that complements this book. By referring to the pages in the provided supplement, you can properly identify those features, recommendations and specifications that are unique to your vehicle.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Emission System Engine Air Filter Passenger Compartment Air Filter Jack Check fuel cap Low tire warning MAX MIN 9
Instrument Cluster WARNING LIGHTS AND CHIMES CHECK FUEL CAP TRUNK AJAR DOOR AJAR TRAC OFF AIR SUSPENSION O/D OFF TRAC ACTIVE SPEED CONTROL 60 COMPASS 20 10 100 120 WASHER LTR/100km 90 140 40 160 100 km MILES/GAL FUEL ECON DIST TO EMPTY AVG SPEED TRIP A B E/M 20 180 110 < FILL ON LEFT 120 H SERVICE ENGINE SOON 70 80 80 30 km 60 50 40 CIRCLE SLOWLY MPH P F km/h R N D 2 1 AIR BAG 1 2 E BRAKE Warning lights and gauges can alert you to a vehicle condition that may become serious
Instrument Cluster These temporary malfunctions can be corrected by filling the fuel tank with high quality fuel of the recommended octane and/or properly installing and securely tightening the fuel cap. After three driving cycles without these or any other temporary malfunctions present, the light should turn off. (A driving cycle consists of a cold engine startup followed by mixed city/highway driving.) No additional vehicle service is required.
Instrument Cluster Brake system warning Illuminates if the parking brake is engaged. Also momentarily BRAKE illuminates at start up to ensure the ! circuit is functional. If the brake warning lamp does not illuminate at these times, or illuminates after releasing the parking brake, seek service immediately. Refer to Brakes in the Driving chapter for more information. Anti-lock brake system (ABS) Momentarily illuminates at start up to ensure the circuit is functional.
Instrument Cluster Engine oil pressure Illuminates when the oil pressure falls below the normal range. Check the oil level and add oil if needed. Refer to Engine oil in the Maintenance and specifications chapter. Engine coolant temperature Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as safely possible, switch off the engine and let it cool. Never remove the coolant recovery cap while the engine is running or hot.
Instrument Cluster Trac off Illuminates when the Traction Controly system has been disabled (by the driver or as a result of a system failure). For more information, refer to the Driving chapter. Air suspension Illuminates when the air suspension switch is turned OFF or the air suspension system requires servicing.
Instrument Cluster O/D off Illuminates when the overdrive function has been turned OFF using the Transmission Control Switch (TCS). If the light does not come on or the light flashes steadily, have your vehicle serviced as soon as possible, damage to the transmission could occur. TRUNK AJAR DOOR AJAR TRAC OFF AIR SUSPENSION CIRCLE SLOWLY km O/D OFF TRAC ACTIVE SPEED CONTROL COMPASS Turn signals Illuminates when the turn signals or the hazard lights are turned on.
Instrument Cluster Trunk ajar Illuminates when the trunk is not completely closed. This light will flash five times and sound a tone for one second, then the light remains on. TRUNK AJAR DOOR AJAR TRAC OFF AIR SUSPENSION CIRCLE SLOWLY km O/D OFF TRAC ACTIVE SPEED CONTROL COMPASS Safety belt warning chime Sounds to remind you to fasten your safety belts. BeltMinder chime Sounds intermittently to remind you to fasten your safety belts.
Instrument Cluster GAUGES CHECK FUEL CAP TRUNK AJAR DOOR AJAR TRAC OFF AIR SUSPENSION O/D OFF TRAC ACTIVE SPEED CONTROL 60 COMPASS 20 10 100 120 WASHER LTR/100km 90 140 40 160 100 km MILES/GAL FUEL ECON DIST TO EMPTY AVG SPEED TRIP A B E/M 20 180 110 < FILL ON LEFT 120 H SERVICE ENGINE SOON 70 80 80 30 km 60 50 40 CIRCLE SLOWLY MPH P F km/h R N D 2 1 AIR BAG 1 2 E BRAKE Engine coolant temperature gauge Indicates the temperature of the engine coolant.
Instrument Cluster Fuel gauge Displays approximately how much fuel is in the fuel tank. The fuel gauge may vary slightly when the vehicle is in motion or on a grade. When refueling the vehicle from empty indication, the amount of fuel that can be added will be less than the advertised capacity due to the reserve fuel. < FILL ON LEFT F 1 2 E Speedometer Indicates the current vehicle speed.
Entertainment Systems AM/FM STEREO CASSETTE VOL - PUSH ON AM FM1 BASS CLK ST TREB BAL FADE FM SEEK SCAN SIDE REW EJ TUNE 1 2 3 4 5 TAPE AMS 1-2 FF 6 Your vehicle is equipped with a delayed accessory feature. This feature enables the audio playing media to continue playing up to 10 minutes after the ignition has been turned off, or until a door is opened. Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume.
Entertainment Systems If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. BASS Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output.
Entertainment Systems Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. FADE Seek function The seek function control works in radio mode. Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. Scan function The scan function works in radio mode.
Entertainment Systems AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the AM control to select from AM selections, and press the FM control to select from FM1 or FM2 memory preset stations. AM/FM select in tape mode Press this control to stop tape play and begin radio play. Radio station memory preset The radio is equipped with six station memory preset controls.
Entertainment Systems • • to decrease hours and to increase hours. To set the minute, press and hold the CLK control and press: CLK TAPE AMS • • to decrease minutes and to increase minutes. The CLK control will allow you to switch between media display mode (radio station, stereo information, etc.) and clock display mode (time). When in clock mode, the media information will display for 10 seconds, when the radio is turned on, and then revert to clock information.
Entertainment Systems Tape select • To enter tape mode while in radio mode, press the TAPE AMS control. CLK TAPE AMS Automatic Music Search The Automatic Music Search feature allows you to quickly locate the beginning of the tape selection CLK being played or to skip to the next selection. TAPE To activate the feature, momentarily AMS depress the TAPE AMS button. Then, press either REW (for the beginning of the current selection) or FF (to advance to the next selection).
Entertainment Systems Tape direction select Press SIDE and 1–2 at the same time to play the alternate side of a tape. Eject function Press the control to stop and eject a tape. SIDE REW 1-2 FF EJ DolbyT noise reduction Dolbyt noise reduction operates only in tape mode. Dolbyt noise 4 reduction reduces the amount of hiss and static during tape playback. control to activate (and deactivate) Dolbyt noise Press the reduction.
Entertainment Systems PREMIUM AM/FM STEREO/CASSETTE (CD CHANGER COMPATIBLE) BASS BAL SEL TREB VOL PUSH ON CD EJ TAPE AM FM TUNE SEEK MUTE REW FF SIDE 1.
Entertainment Systems Your audio system is equipped with selective lighting, a unique lighting strategy. This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off. Those controls which have a function for the specific mode of operation selected will be lit, while the controls which have no function for that mode will be turned off.
Entertainment Systems With the radio on, press and hold the volume control for five seconds, until the display reads SPEED VOL, then press: VOL PUSH ON • to increase volume compensation • to decrease or shut off the volume compensation Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the BASS control. Use the SEL control to increase or decrease the amount of bass.
Entertainment Systems Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control. Use the SEL control to adjust the sound between the speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the FADE control. Use the SEL control to adjust the sound between the front and rear speakers.
Entertainment Systems Seek function for CD changer • Press to seek to the previous SEEK track of the current disc. If a selection has been playing for three seconds or more and you press , the CD changer will replay that selection from the beginning. • Press to seek forward to the next track of the current disc. After the last track has been completed, the first track of the current disc will automatically replay. Scan function The scan function works in radio, tape or CD mode (if equipped).
Entertainment Systems AM/FM select in radio mode The AM/FM control allows you to select AM or FM frequency bands. Press the control to toggle between AM, FM1 or FM2 memory preset stations. AM/FM select in tape mode Press this control to stop tape play and begin radio play. AM/FM select in CD mode Press this control to stop CD play and begin radio play. Radio station memory preset The radio is equipped with six station memory preset controls.
Entertainment Systems If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available. To deactivate autoset and return to your audio system’s manually set memory stations, press the control again. Setting the clock with radio data system (RDS) feature (if equipped) This feature applies to vehicles not equipped with a separate, instrument panel mounted clock.
Entertainment Systems Rewind The rewind control works in tape REW and CD modes. 1 • In tape mode, radio play will continue until rewind is stopped (with the TAPE control) or the beginning of the tape is reached. • In CD mode, pressing the REW control for less than three seconds results in slow rewind. Pressing the control for more than three seconds results in fast rewind. Fast forward The fast forward control works in FF tape and CD modes (if equipped).
Entertainment Systems DolbyT noise reduction Dolbyt noise reduction operates only in tape mode. Dolbyt noise reduction reduces the amount of 4 hiss and static during tape playback. Press the control to activate (and deactivate) Dolbyt noise reduction. The Dolbyt noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation. Dolbyt and the double-D symbol are registered trademarks of Dolbyt Labratories Licensing Corporation.
Entertainment Systems • Use SEEK, TUNE or radio presets 1 through 6 to select a phone number previously programmed in the phone. • Press the phone/mute control again to send and end calls. This control will mute the playing media even if your vehicle is not equipped with a factory-installed cellular phone. Press the control again to return to the playing media. Mute mode Press the control to mute the playing media. Press the control again to return to the playing media.
Entertainment Systems Press the DSP control until one of the following appears: • ALL SEATS • DRIVER SEAT • REAR SEATS Use the SELECT control to change the equalization to the desired mode. RDS DSP SEL Radio data system (RDS) feature This feature allows your audio system to receive station identification or program type from RDS-equipped FM radio stations.
Entertainment Systems • Use the SEL control to select ON or OFF. With the feature on, use the SEEK or SCAN control to SEL find a radio station broadcasting a traffic report (if it is broadcasting RDS data). Traffic information is not available in most U.S. markets. Program type • Press the RDS control until the FIND program type is displayed. • Use the SEL control to select the program type.
Entertainment Systems • Use the SEL control to select TYPE (the display shows the program type), NAME (the display shows the call letters of the station) or NONE. CD CHANGER (IF EQUIPPED) Your CD changer is located in the trunk. 1. Slide the door to access the CD changer magazine. 2. Press to eject the magazine. 3. Pull the lever to remove a CD tray from the magazine.
Entertainment Systems 4. Insert one disc into each CD tray of the magazine (up to 6 discs). Ensure that the label side is facing up. If you pull too hard on the disc holder, the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine. 5. Insert each CD tray, with the disc loaded, all the way into the CD magazine. 6. Insert the CD magazine into the changer. 7. Slide the door to the left to close. Use only compact discs containing this mark.
Entertainment Systems Radio power must be turned on to play the CDs in the changer. The magazine may be stored in the glove compartment when not being used. The CD magazine may be inserted or ejected with the radio power off. Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur. TROUBLESHOOTING THE CD CHANGER (IF EQUIPPED) The laser beam used in the compact disc player is harmful to the eyes. Do not attempt to disassemble the case.
Entertainment Systems Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur. CLEANING CASSETTE PLAYER (IF EQUIPPED) Clean the tape player head with a cassette cleaning cartridge after 10 to 12 hours of play in order to maintain the best sound and operation. CASSETTE AND CASSETTE PLAYER CARE • Use only cassettes that are 90 minutes long or less. • Do not expose tapes to direct sunlight, high humidity, extreme heat or extreme cold.
Entertainment Systems RADIO RECEPTION FACTORS Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their strength/volume relative to other stations. • Terrain.
Climate Controls ELECTRONIC AUTOMATIC TEMPERATURE CONTROL (EATC) SYSTEM The EATC system will maintain a ˚F selected temperature and automatically control airflow. You AUTO can override automatic operation with any of the override controls, the fan speed control or the steering wheel controls (if equipped). EXT Turning the EATC on Press AUTO, any of the override controls or the fan speed control. The EATC will only operate when the vehicle is running.
Climate Controls If unusual conditions exist (i.e.-window fogging, etc.), the manual override controls allow you to select airflow locations and the fan control allows you to adjust fan speed as necessary. Temperature selection The display window indicates the selected temperature, function (AUTO or one of the override controls) and manual control of fan speed ( ) if automatic fan speed is not desired.
Climate Controls Fan speed ( ) When AUTO is pressed, fan speed is adjusted automatically for existing conditions. You can override fan speed at any time. To control fan speed manually, press the fan control or the steering wheel fan speed control (if equipped) to MAX EXT OFF AUTO A/C cancel automatic fan speed operation. Press the control up for higher fan speed or down for lower fan speed. Press the steering wheel control (if equipped) up for higher fan speed or down for lower fan speed.
Climate Controls • • • • • • (Panel)-Distributes outside air through the instrument panel registers. However, the air cannot be cooled below the outside temperature because the air conditioning does not operate in this mode. (Panel and floor) -Distributes outside air through the instrument panel registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode. The air will be heated or cooled based on the temperature selection.
Climate Controls If a manual override function is selected while the outside temperature is displayed, the new function will be displayed for four seconds after it is changed, then the outside temperature will return to the window along with the override selection. The outside temperature reading is most accurate when the vehicle is moving. Higher readings may be obtained when the vehicle is not moving.
Climate Controls • If your vehicle has been parked with the windows closed during hot weather, the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open. This will force most of the hot, stale air out of the vehicle. Then operate the air conditioner as you would normally. • Do not place objects over the defroster outlets. These objects may block airflow and reduce visibility through your windshield.
Lights HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. OFF P Your vehicle’s headlamp system is equipped with a feature that will not dim the instrument panel lighting when the headlamps are on in the daytime. Even during full daylight, the instrument panel lighting will still be visible with the headlamp operating.
Lights Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Light (DRL) System does not activate your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision. The Daytime Running Light (DRL) system will automatically illuminate the tail lamps and parking lamps at dusk (when the headlamp control is in the OFF position).
Lights AIMING THE HEADLAMPS Your vehicle is equipped with a Vehicle Headlamp Aim Device (VHAD) on each headlamp. Each headlamp may be properly aimed in the vertical (up/down) and the horizontal (left/right) directions using your VHAD system. The headlamps on your vehicle are properly aimed at the assembly plant. A bubble (vertical indicator) that is not centered between the two red lines does not necessarily indicate out-of-aim headlamps.
Lights Turning the horizontal adjusting screw in the direction of the arrow changes the horizontal aim as shown. Vertical aim adjustment 1. Park the vehicle on a level surface. 2. With the hood open, remove protective cover, then locate the bubble level and the vertical adjustment screw. The adjustment screw is located on the outboard side of the headlamp. 3. The “U” and “D” on the bubble indicate the directional change (up or down) of the vertical aim. 4.
Lights TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. HI LO F S OFF INTERIOR LAMPS Rear courtesy/reading lamps The courtesy lamp lights when: • any door is opened. • any of the remote entry controls are pressed and the ignition is OFF. With the ignition key in the ACC or ON position, the reading lamp can be turned on by pressing the rocker control.
Lights Do not remove lamp bulbs unless they will be replaced immediately. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect performance. Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to assure lamp performance, light brightness and pattern and safe visibility.
Lights Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position. 2. Open the hood. 3. Twist the plastic knobs and remove the protective cover from the back of the headlamps. Lift the cover and pull towards the windshield. 4. Remove headlamp by taking the retainer pins out. Pull headlamp forward to access bulb connector. 5. Disconnect the electrical connector from the bulb by pulling rearward.
Lights 6. Remove the bulb retaining ring by rotating it counterclockwise (when viewed from the rear) to free it from the bulb socket, and slide the ring off the plastic base. Keep the ring to retain the new bulb. 7. Without turning, remove the old bulb from the lamp assembly by gently pulling it straight back out of the lamp assembly. To install the new bulb: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass.
Lights Replacing front parking lamp/turn signal lamp bulbs 1. Make sure the headlamp control is in the OFF position. 2. Open the hood. 3. Twist the plastic knobs and remove the protective cover from the back of the headlamps. Lift the cover and pull towards the windshield. 4. Remove headlamp by taking the retainer pins out. Pull headlamp forward to access bulb connector. 5. Disconnect the electrical connector from the bulb socket. 6. Rotate the bulb socket counterclockwise and remove from lamp assembly. 7.
Lights Replacing high-mount brakelamp bulbs 1. Remove the lamp cover by prying up. 2. Rotate the bulb socket counterclockwise and remove from lamp assembly. 3. Carefully pull the bulb straight out of socket and push in the new bulb. 4. To complete installation, follow the removal procedure in reverse order. Replacing license plate lamp bulbs 1. Remove two screws, grommets and the license plate lamp assembly from the trunk lid. 2. Carefully pull the bulb from the socket and push in the new bulb. 3.
Driver Controls WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals. Push the control on the end of the stalk to activate washer. Push and hold for a longer wash cycle.
Driver Controls Changing the wiper blades To make changing the wiper blades easy, turn the ignition to ACC, then turn the wipers on. When the wipers reach the vertical position, turn the ignition to LOCK. To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 3.
Driver Controls Never adjust the steering wheel when the vehicle is moving. ILLUMINATED VISOR MIRROR (IF EQUIPPED) To turn on the visor mirror lamps, lift the mirror cover. CLOCK (IF EQUIPPED) If your vehicle is not equipped with an instrument panel mounted clock, refer to Setting the Clock section in the Entertainment chapter. Press the right control to increase the time displayed. Press the left control to decrease the time displayed.
Driver Controls AUXILIARY POWER POINT Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. The auxiliary power point is located under the instrument panel. This outlet should be used in place of the cigarette lighter for optional electrical accessories.
Driver Controls MIRRORS Automatic dimming inside rear view mirror (if equipped) Your vehicle is equipped with an inside rear view mirror which has an auto-dimming function (available as an option on the outside driver’s side mirror). The electronic day/night mirror will change from the normal state to the non-glare state when bright lights (glare) reach the mirror. When the mirror detects bright light from front or behind, it will automatically adjust (darken) to minimize glare.
Driver Controls 2. Move the control in the direction you wish to tilt the mirror. L R 3. Return to the center position to lock mirrors in place. Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors.
Driver Controls SPEED CONTROL To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not shift the gearshift lever into N (Neutral) with the speed control on. ON OFF Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased.
Driver Controls If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal. Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill. If your vehicle speed is faster than the set speed while driving on a downhill, you may want to shift to the next lower gear or apply the brakes to reduce your vehicle speed.
Driver Controls • Depress the brake pedal. When the desired vehicle speed is reached, press SET ACCEL. RES SET ACCEL COAST To disengage speed control • Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. ON OFF To return to a previously set speed • Press RES/RESUME. For RES/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph).
Driver Controls Indicator light Indicator message This message is displayed in the Message Center when either the SET ACCEL or RES/RESUME controls are pressed. It turns off when the speed control OFF is pressed, the brake is applied or the ignition is turned to the OFF position. SPEED CONTROL STEERING WHEEL CONTROLS (IF EQUIPPED) These controls allow you to operate some radio and climate control features. Radio control features • Press BAND/MODE to select AM, FM1, FM2, TAPE or CD (if equipped).
Driver Controls Climate control features • Press TEMP up or down to adjust temperature. • Press FAN up or down to adjust fan speed. MOON ROOF (IF EQUIPPED) To open the moon roof: • Press and release the control. • For one-touch operation, press and release the rear portion of the control; this will fully open the moon roof. • To stop one-touch operation at the desired position, press and release the forward portion of the control. To close the moon roof: • Press and hold the front portion of the control.
Driver Controls Programming Do not program the HomeLinkt Universal Transceiver with the vehicle parked in the garage. 1. Prepare for programming the HomeLinkt Universal Transceiver by erasing the three factory default codes by holding down the two outside buttons until the red light begins to flash after 20 seconds. Release both buttons. 2.
Driver Controls Operating the HomeLinkT Universal Transceiver Once programmed, the HomeLinkt Universal Transceiver can be used in place of hand-held transmitters. To operate, simply press and release the appropriate HomeLinkt button (the red light will illuminate, indicating the signal is being transmitted).
Driver Controls The 2nd or 3rd press from step 3 will activate the door. The HomeLinkt Universal Transceiver has now been trained to the receiver. The remaining two buttons may now be programmed if this has not previously been done. Erasing HomeLinkT buttons Individual buttons cannot be erased, however, to erase the three programmed buttons: 1. Hold down the two outside buttons until the red light begins to flash after 20 seconds. 2. Release both buttons.
Driver Controls To program your hand-held transmitters: • Continue to hold the button on the HomeLinkt Universal Transceiver. • Press and re-press the hand-held transmitter button every two seconds until the red light changes from a slow to a fast flash. VEHICLE COMMUNICATION SYSTEM (IF EQUIPPED) The Vehicle Communication System is designed to provide a variety of safety enhancing services and offers access to hands-free calling through the Vehicle Communication System wireless phone.
Driver Controls 1. SOS BUTTON — In an emergency situation or for roadside assistance, press this button to contact the Lincoln Response Center. A response center representative will locate your vehicle and dispatch assistance if needed. Once a connection is made to the Lincoln Response Center, only the response center representative will be able to disconnect the call.
Driver Controls Volume Control — Volume can be controlled using the audio system controls. VOL PUSH ON First Owner/First Time Activation • After receiving the wireless phone and welcome kit, please contact Sprint PCS at 1–866–PCS-AUTO (1–866–727–2886) and select option “1” for activations. When calling Sprint PCS to activate your phone, please do not call from your new wireless phone.
Driver Controls Vehicle Communication System Limitations • Vehicle Communication System services are available in the 48 contiguous states and Hawaii • Vehicle Communication System services are not available in Alaska • Only available within range of the cellular systems • Connection limited by atmospheric and topographical conditions • Connection limited by cellular network capabilities and infrastructure • The wireless phone must have an active wireless service plan with Sprint PCS and docked in the docki
Driver Controls Phone accessories can be purchased at Sprint PCS stores. Billing or services issues should be directed to Sprint PCS at 1–866–PCS-AUTO (1–866–727–2886). Select “2” for Client Services. ELECTRONIC MESSAGE CENTER The electronic message center only works when the ignition is in the ON position. The message center allows you to: • see problems such as door ajar TRUNK AJAR DOOR AJAR and trunk ajar. CIRCLE TRAC OFF AIR SUSPENSION SLOWLY • see the compass direction.
Driver Controls Selectable features Select Each press of the SELECT control WASHER FUEL ECON will select a different feature as LTR/100km DIST TO EMPTY follows: AVG SPEED • FUEL ECON TRIP A B • DIST TO EMPTY E/M km MILES/GAL • AVG SPEED • TRIP A/TRIP B • E/M For descriptions of the SELECT features, refer to “Message center functions” later in this chapter. Reset Press this control to reset the selected message center function to zero. (The only functions which can be reset are FUEL ECON and TRIP A or B.
Driver Controls Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 1 15 2. Locate the compass module and 2 14 the calibration button mounted on 3 the center rear view mirror post. 13 4 12 3. Turn ignition to the ON position. 11 4. Press and hold the CALIBRATION 5 6 10 BUTTON switch located on top of the compass module until the 7 8 9 message center display changes to show the current zone setting. 5.
Driver Controls 3. Press and hold the CALIBRATION TRUNK AJAR DOOR AJAR BUTTON for 2 to 4 seconds until CIRCLE CIRCLE SLOWLY is displayed on the TRAC OFF AIR SUSPENSION SLOWLY message center. km 4. Release pressure from the button. O/D OFF TRAC ACTIVE 5. Slowly drive the vehicle in a SPEED CONTROL COMPASS circle (less than 5 km/h [3 mph]) until the CIRCLE SLOWLY indicator turns off. This will take up to five circles to complete calibration. 6. The compass is now calibrated.
Driver Controls You may notice gradual improvement in fuel economy over the course of your vehicle’s break-in period (approximately 1 600 kilometers [1 000 miles]). 1. Set the speed control. Refer to Speed control in this chapter. 2. Select FUEL ECON FUEL ECON DIST TO EMPTY AVG SPEED TRIP A B E/M 3. Press the RESET control to clear SELECT RESET the system memory. • Actual highway fuel economy is now displayed.
Driver Controls The DTE function will flash for 5 seconds and sound a tone for 1 second when you have approximately: • 80 km (50 miles) left before you run out of fuel • 40 km (25 miles) • 16 km (10 miles) If “CO” or “CS” is displayed, there is a problem with the fuel indication system and you should contact your dealer for service as soon as possible. AVG speed To use this function, select AVG SPEED and press the RESET control.
Driver Controls OVERDRIVE CONTROL Activating overdrive (Overdrive) is the normal drive position for the best fuel economy. The overdrive function allows automatic upshifts and downshifts through all available gears. Deactivating overdrive Press the Transmission Control Switch (TCS) located on the end of O/D ON/OFF the gearshift lever. The Transmission Control Indicator Light (TCIL) will illuminate on the instrument cluster. The transmission will operate in all gears except overdrive.
Driver Controls FUEL DOOR RELEASE Your vehicle is equipped with a locking fuel door. To open the door, press the control located on the door. Fuel filler door override release If the remote release is inoperative, open the trunk, then pull the override release handle located inside the trunk to open the fuel filler door.
Driver Controls • To program position two, repeat the previous procedure using control 2. • To program position three, repeat the previous procedure but press controls 1 and 2 simultaneously. A position can only be recalled when the transmission gearshift is in Park. A memory seat position may be programmed at any time. The memory positions are also recalled when you press your remote entry transmitter UNLOCK control.
Driver Controls Radio/climate controls lockout The rear radio/climate control feature can be locked out by pressing the 3 and the 5 buttons on the radio simultaneously while the radio is on. To enable the rear radio/climate controls, press the 3 and the 5 buttons again. Remote seat adjustment The rear passenger can move the front passenger seat forward or backward using the control located in the rear center console. Move the control forward or backward to move front passenger seat.
Driver Controls Remote seat adjustment lockout The window lockout control, located WINDOW LOCK on the drivers door, will also lockout the remote seat adjustment. To lock out the remote seat adjustment feature, press the right side of the control. Press the left side to restore the remote seat adjustment control. POSITIVE RETENTION FLOOR MAT Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in.
Locks and Security KEYS The vehicle is equipped with a master key and valet key lock system. The master key will access doors, trunk, glove box, ignition and remote trunk release. The valet key (marked “valet”) will access doors and ignition only. Before using this key, lock the trunk remote control to disable the Trunk remote control on the drivers door, then lock the glove compartment with your master key. POWER DOOR LOCKS Press control to unlock or lock all doors.
Locks and Security INTERIOR LUGGAGE COMPARTMENT RELEASE Your vehicle is equipped with a mechanical interior luggage compartment release handle that provides a means of escape for children and adults in the event they become locked inside the luggage compartment. Adults are advised to familiarize themselves with the operation and location of the release handle. To open the luggage compartment door (lid) from the inside, pull the illuminated “T” shaped handle and push up on the trunk lid.
Locks and Security REMOTE ENTRY SYSTEM This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Locks and Security Deactivating/activating the horn chirp feature The horn chirp feature can be turned on/off through the following procedure: Complete steps 1-7 within 30 seconds or you must repeat the procedure. Wait 30 seconds before repeating the procedure. 1. Turn ignition key to ON. 2. Press power door unlock control on the door panel 3 times. 3. Turn ignition key from ON to OFF. 4. Press power door unlock control 3 times. 5. Turn ignition key back to ON. The doors will lock and unlock. 6.
Locks and Security The remote entry system allows you to open the trunk while the ignition is in any position. However, if the ignition is in the ON position and the gearshift is in D (Drive), the trunk will only open if the vehicle is moving 5 km/h (3 mph) or slower. Replacing the battery The remote transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle.
Locks and Security Replacing lost transmitters Take all your vehicle’s transmitters to your dealer if service is required.
Locks and Security Autolock The autolock feature will lock all of the vehicle doors when: • all doors are closed • the engine is running and • you shift into any gear putting the vehicle in motion The autolock feature repeats when: • any door, except the drivers door, is opened then closed while the engine is running and • you put the vehicle in motion Autolock can also be activated or deactivated using the following procedure: You must complete steps 1 through 7 within 30 seconds or the procedure will have
Locks and Security Press the control once to unlock the driver’s door and move the memory features to the corresponding memory position, just as if you had pressed the memory control in the vehicle. • transmitter #1 will recall memory feature position one. • transmitter #2 will recall memory feature position two. • If a third or fourth transmitter is added, it will not recall a memory position. Memory seat positions can be changed at any time.
Locks and Security KEYLESS ENTRY SYSTEM (IF EQUIPPED) With the keyless entry keypad, you can: 1 2 3 4 5 6 7 8 9 0 • lock or unlock the vehicle doors without using the key Your vehicle has a factory-set 5–digit code that operates the keyless entry system. You can also program your own 5–digit personal entry code.
Locks and Security You can program up to three personal codes to unlock your vehicle. These codes do not replace the permanent code that the dealership gave you. Erasing personal code To erase all of the personal entry codes programmed to a vehicle: 1. Enter the factory-set code. 1 2 3 4 5 6 7 8 9 0 2. Press 1/2 within 5 seconds of step 1. 3. Press and hold 1/2 for two seconds.
Locks and Security Locking doors with the keyless entry system It is not necessary to enter the factory-set code prior to locking all doors. To lock the doors: • Press 7/8 and 9/0 at the same time. 1 2 3 4 5 6 7 8 9 0 SECURILOCKY PASSIVE ANTI-THEFT SYSTEM SecuriLocky passive anti-theft system is an engine immobilization system. This system prevents the engine from being started unless a coded key programmed to your vehicle is used.
Locks and Security Key information Your vehicle is supplied with two coded keys. Only a coded key will start your vehicle. Spare coded keys can be purchased from your dealership. Your dealership can program your key or you can “do it yourself”, refer to Programming spare keys. Large metallic objects, electronic devices on the key chain that can be used to purchase gasoline or similar items, or a second key on the same key ring as the coded key may cause vehicle starting issues.
Locks and Security If your keys are lost or stolen you will need to do the following: • Use your spare key to start the vehicle, or • Have your vehicle towed to a dealership or locksmith. The key codes will need to be erased from your vehicle and new key codes will need to be re-coded. Replacing coded keys can be very costly and you may want to store an extra programmed key away from the vehicle in a safe place to prevent an unforeseen inconvenience. The correct coded key must be used for your vehicle.
Locks and Security Please read and understand the entire procedure before you begin. 1. Insert the first previously programmed coded key into the 4 ignition and turn the ignition from 3 3 (OFF) to 4 (ON) (maintain ignition 5 in 4 (ON) for at least one second). 2. Turn ignition to 3 (OFF) then 2 2 (LOCK) and remove the first coded key from the ignition. 1 3.
Seating and Safety Restraints SEATING Head restraints Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. Refer to the following to raise and lower the head restraints.
Seating and Safety Restraints To adjust the front seatback using the manual recliner: • Lift and hold the handle located on the side of the seat. • Lean against the seatback to adjust it to your desired position. You can recline the seat back or bring it forward. • Release the handle when the desired position has been reached. Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press one side of the control to adjust firmness.
Seating and Safety Restraints Press the control to recline the seatback forward or backward. Press to move the seat forward or backward. Press to move the front portion of the seat cushion up or down. Press to move the rear portion of the seat cushion up or down.
Seating and Safety Restraints Heated seats (if equipped) The heated seat controls are located on the door trim panel. To operate the heated seats: • Slide the control to BACK to heat the seatback only. BACK • Slide the control to BOTH to heat the seatback and the seat cushion. BOTH • Rotate the thumbwheel to select the desired heat (from 0 (OFF) to 5 (HI)). Allow five minutes for the heat level to stabilize.
Seating and Safety Restraints Memory seats/rearview mirrors/adjustable pedals (if equipped) This system allows automatic SET positioning of the driver seat, outside rearview mirrors, and 2 1 adjustable pedals to three programmable positions. The memory seat control is located on the driver door. • To program position one, move the driver seat to the desired position using the seat controls. Press the SET control. The SET control indicator light will briefly illuminate.
Seating and Safety Restraints • • • • Front crash severity sensor. Restraints Control Module (RCM) with impact and safing sensors. Restraint system warning light and back-up tone. The electrical wiring for the air bags, crash sensor(s), safety belt pretensioners, front safety belt usage sensors, driver seat position sensor, passenger occupant classification sensor (if equipped), and indicator lights.
Seating and Safety Restraints Driver’s seat position sensor The driver’s seat position sensor allows your Personal safety system to tailor the deployment level of the driver dual-stage air bag based on seat position. The system is designed to help protect smaller drivers sitting close to the driver air bag by providing a lower air bag output level.
Seating and Safety Restraints Front safety belt usage sensors The front safety belt usage sensors detect whether or not the driver and front outboard passenger safety belts are fastened. This information allows your Personal safety system to tailor the air bag deployment and safety belt pretensioner activation depending upon safety belt usage. Refer to Safety belt section in this chapter.
Seating and Safety Restraints If any of these things happen, even intermittently, have the Personal safety system serviced at your dealership or by a qualified technician immediately. Unless serviced, the system may not function properly in the event of a collision. Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. To reduce the risk of injury, make sure children sit where they can be properly restrained.
Seating and Safety Restraints Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder. 3) Never use a single belt for more than one person.
Seating and Safety Restraints Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of approximately 8 km/h (5 mph) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers.
Seating and Safety Restraints • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Ford Motor Company recommends that all safety belt assemblies and attaching hardware should be inspected by a qualified technician after any collision.
Seating and Safety Restraints Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions. Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button and slide the height adjuster down. To raise the height of the shoulder belt, slide the height adjuster up.
Seating and Safety Restraints The lap belt does not adjust automatically. Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. To tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips. Shorten and fasten the belt when not in use.
Seating and Safety Restraints Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON position... Then... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds.
Seating and Safety Restraints If... The driver’s safety belt is buckled before the ignition switch is turned to the ON position... Then... The BeltMinder feature will not activate. The purpose of the BeltMinder is to remind occasional wearers to wear safety belts all of the time. The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given...
Seating and Safety Restraints Reasons given... “Belts wrinkle my clothes” “The people I’m with don’t wear belts” “I have an air bag” “I’d rather be thrown clear” Consider... Possibly, but a serious crash can do much more than wrinkle your clothes, particularly if you are unbelted. Set the example, teen deaths occur 4 times more often in vehicles with TWO or MORE people. Children and younger brothers/sisters imitate behavior they see. Air bags offer greater protection when used with safety belts.
Seating and Safety Restraints • • • • the ignition switch is in the OFF position all vehicle doors are closed the driver’s safety belt is unbuckled the parklamps/headlamps are in OFF position (If vehicle is equipped with Autolamps, this will not affect the procedure.) To reduce the risk of injury, do not deactivate/activate the Belt Minder feature while driving the vehicle. 1. Turn the ignition switch to the RUN (or ON) position. (DO NOT START THE ENGINE) 2.
Seating and Safety Restraints Safety belt extension assembly If the safety belt is too short when fully extended, there is a 20 cm (8 inch) safety belt extension assembly that can be added (part number 611C22). This assembly can be obtained from your dealer at no cost. Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label.
Seating and Safety Restraints AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) CHECK TRAC 50 60 70 40 80 80 30 60 20 OFF 10 P H SERVICE ENGINE SOON 100 BAL BASS 120 90 SEL 140 40 160 VOL PUSH ON 100 TREB FADE 20 180 110 120 MPH km/h < FILL ON CD LEFT F 1 EJ TAPE RDS 2 SEEK MUTE SCAN TUNE AUTO E AM FM 1 2 3 REW FF SIDE 1 2 4 5 6 COMP SHUFF LO F PANEL DIM S OFF MIST RES ON SET ACCEL RESET SELECT OFF COAST FRONT REAR EXT OFF AUTO MAX A/C Your vehicl
Seating and Safety Restraints Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. National Highway Traffic Safety Administration (NHTSA) recommends a minimum distance of at least 25 cm (10 inches) between an occupant’s chest and the driver air bag module. Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries.
Seating and Safety Restraints Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision. Air bags can kill or injure a child in a child seat.
Seating and Safety Restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the air bag. Small amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic.
Seating and Safety Restraints • a readiness light and tone. • diagnostic module. • and the electrical wiring which connects the components. The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors.
Seating and Safety Restraints Do not lean your head on the door. The side air bag could injure you as it deploys from the side of the seatback. Do not attempt to service, repair, or modify the air bag supplemental restraint system, its fuses or the seat cover on a seat containing an air bag. See your Ford or Lincoln Mercury dealer. All occupants of the vehicle including the driver should always wear their safety belts even when an air bag SRS is provided.
Seating and Safety Restraints The air bag SRS is designed to activate when the vehicle sustains lateral deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation.
Seating and Safety Restraints • The readiness light will not illuminate immediately after ignition is turned on. • A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and light are repaired. If any of these things happen, even intermittently, have the SRS serviced at your dealership or by a qualified technician immediately. Unless serviced, the system may not function properly in the event of a collision.
Seating and Safety Restraints Children and safety belts If the child is the proper size, restrain the child in a safety seat. Children who are too large for child safety seats (as specified by your child safety seat manufacturer) should always wear safety belts. Follow all the important safety restraint and air bag precautions that apply to adult passengers in your vehicle.
Seating and Safety Restraints Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision. When installing a child safety seat: • Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter.
Seating and Safety Restraints Installing child safety seats in combination lap and shoulder belt seating positions Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back. 1. Position the child safety seat in a seat with a combination lap and shoulder belt. Children 12 and under should be properly restrained in the rear seat whenever possible. 2.
Seating and Safety Restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it. 5.
Seating and Safety Restraints 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly tilt the seat forward and back to make sure the seat is securely held in place. To check this, grab the seat at the belt path and attempt to move it side to side and forward and back.
Seating and Safety Restraints The tether strap anchors in your vehicle are in the following positions (shown from top view): Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor. 1. Position the child safety seat on the seat cushion. 2. Route the child safety seat tether strap over the back of the seat.
Seating and Safety Restraints 5. Clip the tether strap to the anchor as shown. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 6. Refer to the Installing child safety seats in combination lap and shoulder belt seating positions section of this chapter for further instructions to secure the child safety seat. 7. Tighten the child safety seat tether strap according to the manufacturer’s instructions.
Driving STARTING Positions of the ignition 1. ACCESSORY, allows the electrical 4 accessories such as the radio to 3 operate while the engine is not 5 running. 2. LOCK, locks the steering wheel, 2 automatic transmission gearshift lever and allows key removal. 1 3. OFF, shuts off the engine and all accessories without locking the steering wheel. 4. ON, all electrical circuits operational. Warning lights illuminated. Key position when driving. 5. START, cranks the engine.
Driving Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions. If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM).
Driving 5. Turn the key to 4 (ON) without turning the key to 5 (START). 4 If there is difficulty in turning the 3 key, firmly rotate the steering wheel 5 left and right until the key turns freely.
Driving 1. Turn the key to 5 (START) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 4 (ON). 2. If the temperature is above –12° C (10° F) and the engine does not start within five seconds on the first try, turn the key to OFF, wait 10 seconds and try again. 4 3 5 2 1 3. If the temperature is below -12° C (10° F) and the engine does not start in 15 seconds on the first try, turn the key OFF and wait 10 seconds and try again.
Driving If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes. These fumes are harmful and could kill you.
Driving Anti-lock brake system (ABS) On vehicles equipped with an anti-lock braking system (ABS), a noise from the hydraulic pump motor and pulsation in the pedal may be observed during ABS braking events. Pedal pulsation coupled with noise while braking under panic conditions or on loose gravel, bumps, wet or snowy roads is normal and indicates proper functioning of the vehicle’s anti-lock brake system. The ABS performs a self-check after you start the engine and begin to drive away.
Driving ABS warning lamp ABS The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal BRAKE braking is still effective unless the ! brake warning light also remains illuminated with parking brake released.
Driving Your vehicle has an automatic parking brake release. To release the parking brake: 1. Turn the ignition to the ON position. 2. Press the brake pedal. 3. Move the gearshift from the P (Park) position to one of the forward gears (the parking brake will not release automatically when you shift into reverse). The brake pedal must remain pressed while the gearshift is moved. If the parking brake fails to release after completing this procedure, use the manual parking brake release lever.
Driving The Traction Controly system will allow your vehicle to make better use of available traction on slippery surfaces. The system is a driver aid which makes your vehicle easier to handle primarily on snow and ice covered roads. During Traction Controly operation you may hear an electric motor type of sound coming from the engine compartment and the engine will not “rev-up” when you push further on the accelerator. This is normal system behavior.
Driving • high crosswinds • wheels out of alignment • loose or worn suspension components Speed sensitive steering The steering in your vehicle is speed sensitive. At high speeds, steering assist will decrease to improve steering feel. At lower speeds, maneuverability will be increased. If the amount of effort required to steer your vehicle changes while driving at a constant vehicle speed, have the power steering system checked by your dealer or a qualified service technician.
Driving AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless the brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the brake pedal depressed: 1. Apply the parking brake, turn ignition key to LOCK, then remove the key. 2.
Driving Driving with a 4–speed automatic transmission Understanding gearshift positions To put your vehicle in gear, start the engine, depress the brake pedal, then move gearshift lever out of P (Park). Hold the brake pedal down while you move the gearshift lever from P (Park) to another position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone. P (Park) Always come to a complete stop before shifting into P (Park).
Driving Overdrive The normal driving position for the best fuel economy. Transmission operates in gears one through four. Overdrive can be deactivated by pressing the transmission control switch on the gearshift lever. The transmission control indicator light (TCIL) will illuminate on the instrument cluster. O/D ON/OFF TRUNK AJAR DOOR AJAR AIR SUSPENSION CIRCLE SLOWLY km O/D OFF SPEED CONTROL COMPASS Drive Not shown on the display.
Driving 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to Overdrive. Selecting 1 (Low) at higher speeds causes the transmission to shift to a lower gear, and will shift to 1 (Low) after vehicle decelerates to the proper speed.
Driving If driving through deep or standing water is unavoidable, proceed very slowly. Never drive through water that is higher than the bottom of the hubs (for trucks) or the bottom of the wheel rims (for cars). Once through the water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal.
Driving engine/transmission combination, any required option weight for trailer towing and the weight of the driver from the GCWR for the towing vehicle. • Maximum Trailer Weight: Maximum weight of a trailer the loaded vehicle (including occupants and cargo) is permitted to tow. It is determined by subtracting the weight of the loaded trailer towing vehicle from the GCWR for the towing vehicle.
Driving Towing a trailer places an additional load on your vehicle’s engine, transmission, brakes, tires and suspension. Inspect these components carefully after towing. Your loaded trailer should weigh no more than 907 kg (2 000 lbs.). Do not exceed the GVWR or the GAWR specified on the certification label. Towing trailers beyond the maximum recommended gross trailer weight could result in engine damage, transmission/axle damage, structural damage, loss of control, and personal injury.
Driving Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system. Your vehicle may not have enough braking power and your chances of having a collision greatly increase. The braking system of the tow vehicle is rated for operation at the GVWR not GCWR. Trailer lamps Trailer lamps are required on most towed vehicles. Make sure your trailer lamps conform to local and Federal regulations.
Driving • If you are driving down a long or steep hill, shift to a lower gear. Do not apply the brakes continuously, as they may overheat and become less effective. • The trailer tongue weight should be 10% of the loaded trailer weight. • After you have traveled 80 km (50 miles), thoroughly check your hitch, electrical connections and trailer wheel lug nuts. • When stopped in traffic for long periods of time in hot weather, place the gearshift in P (Park) and increase idle speed.
Driving An example of recreational towing is towing your vehicle behind a motorhome. The following recreational towing guidelines are designed to ensure that your transmission is not damaged. • Place the transmission in N (Neutral). • Maximum speed is 56 km/h (35 mph). • Maximum distance is 80 km (50 miles). If a distance of 80 km (50 miles) or a speed of 56 km/h (35 mph) must be exceeded, you must disconnect the driveshaft. Ford recommends the driveshaft be removed/installed only by a qualified technician.
Roadside Emergencies GETTING ROADSIDE ASSISTANCE To fully assist if you should have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the Basic warranty period (Canada) or New Vehicle Limited Warranty period (U.S.
Roadside Emergencies If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. To obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who need to obtain reimbursement information, call 1–800–665–2006.
Roadside Emergencies The fuel pump shut-off switch is located on a bracket inside of the luggage compartment. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. Turn the ignition to the ON position. Pause for a few seconds and return the key to the OFF position. 5.
Roadside Emergencies Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses 2A 3A 4A 5A 7.
Roadside Emergencies 27 25 26 18 23 24 16 17 9 22 14 15 7 8 21 19 20 12 6 10 11 13 5 3 4 RELAY 1 1 2 33 32 31 30 29 28 The fuses are coded as follows. 160 Fuse/Relay Location 1 Fuse Amp Rating 10A 2 3 30A 10A 4 5 7.5A 7.
Roadside Emergencies Fuse/Relay Location 9 Fuse Amp Rating 20A 10 10A 11 12 — 15A 13 10A 14 7.5A 15 20A 16 30A 17 10A 18 7.5A 19 10A 20 7.
Roadside Emergencies 162 Fuse/Relay Location 22 Fuse Amp Rating 20A 23 20A 24 25 5A 15A 26 5A 27 28 29 20A 10A 20A 30 7.5A 31 7.
Roadside Emergencies Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses.
Roadside Emergencies The high-current fuses are coded as follows.
Roadside Emergencies Fuse/Relay Location 19 Fuse Amp Rating 30A* 20 21 15A* 15A* 22 23 24 25 20A 15A 20A* 30A** 26 30A CB** 27 20A** 28 — 29 — Relay 1 — Relay 2 — Relay 3 — Relay 4 — Relay 5 — * Mini Fuses ** Maxi Fuses Power Distribution Box Description Subwoofer, I/P Fuse Panel, Fuse 33 Fuel Injectors, PCM Heated Oxygen Sensors, Transmission Solenoids, EVAP Canaster Vent Solenoid, EGR Vacuum Regulator, EVAP Vapor Management Valve Fuel Pump Charging System Auxiliary Power Outlet Passenger Seat (Long
Roadside Emergencies If you use the temporary spare tire continuously or do not follow these precautions, the tire could fail, causing you to lose control of the vehicle, possibly injuring yourself or others.
Roadside Emergencies 2. Place gearshift lever in P (Park), turn engine OFF and block the diagonally opposite wheel. 3. Remove the spare tire and the jack. The jack could be located: • A — under the spare tire or • B — in the wheel well A B On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. OFF Refer to Air suspension system in the Driving chapter for more information. 4. Remove the lug wrench (A) from the jack.
Roadside Emergencies 5. Locate pry off notch (if equipped) and remove the center ornament from the aluminum wheel with the tapered end of the wheel nut wrench that came with your vehicle. Insert and twist the handle, then pry against the wheel. 6. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground.
Roadside Emergencies To lessen risk of personnal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is ONLY meant for changing the tire. • Never use the rear differential as a jacking point. 7. Remove the lug nuts with the lug wrench. 8. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall lug nuts until the wheel is snug against the hub.
Roadside Emergencies Do not attempt to push-start your vehicle. Automatic transmissions do not have push-start capability; also, the catalytic conveter may become damaged. Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its adaptive strategy. As a result of this, the transmission may shift firmly. This operation is considered normal and will not affect function or durability of the transmission.
Roadside Emergencies Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + + – – 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery.
Roadside Emergencies + + – – 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. 5.
Roadside Emergencies Removing the jumper cables + + – – Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + + – – 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery.
Roadside Emergencies + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside Emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. Before your vehicle can be towed, the air suspension control in the luggage compartment must be turned to the OFF position (if equipped).
Customer Assistance GETTING THE SERVICES YOU NEED At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. It is preferred that you return to the Ford dealer where your vehicle was purchased when warranty repairs are needed. However, you may also take your vehicle to another Ford Motor Company or Ford of Canada dealership authorized for warranty repairs.
Customer Assistance In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
Customer Assistance In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the Dispute Settlement Board before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws.
Customer Assistance THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes • available free to owners and lessees of qualifying Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this service without notice and without incurring obligations per applicable state law.
Customer Assistance Board membership The Board consists of: • three consumer representatives • a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities.
Customer Assistance You will receive a letter of explanation if your application does not qualify for Board review. Oral presentations If you would like to make an oral presentation, indicate YES to question 6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made. An oral presentation may be requested by the Board as well.
Customer Assistance UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Customer Assistance If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY WORLDWIDE DIRECT MARKET OPERATIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A. Telephone: (313) 594-4857 FAX: (313) 390-0804 If you are in another foreign country, contact the nearest Ford dealership.
Customer Assistance IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.
Customer Assistance REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Cleaning WASHING THE EXTERIOR OF YOUR VEHICLE Never wash a vehicle that is “hot to the touch” or during exposure to strong, direct sunlight. It is recommended that you wash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo, such as Detail Wash (ZC-3–A), which is available from your authorized Ford, Lincoln or Mercury dealer. Always use a clean sponge or carwash mitt with plenty of water for best results.
Cleaning REPAIRING PAINT CHIPS Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips. Minor scratches or paint damage from road debris may be repaired using the Ultra Touch Prep and Finishing Kit (F7AZ-19K507–BA), which is available at your authorized Ford, Lincoln or Mercury dealer.
Cleaning • Never spray a hot engine with cold water, as damage to the engine block or engine components may occur. • Use caution when using a self-serve power washer (1000psi maximum pressure) to clean the engine, as the high-pressure fluid could penetrate the sealed parts and cause damage. • Never apply anything to any exposed belts in the engine compartment, including the belt dressing.
Cleaning WASHING NON-PAINTED PLASTIC EXTERIOR PARTS Use Detail Wash (ZC-3–A) for routine cleaning. If tar or grease spots are present, clean with Extra Strength Tar and Road Oil Removal (B7A-19520–AA). Use only approved products to clean plastic parts. These products are available from your authorized Ford, Lincoln or Mercury dealer. WASHING THE EXTERIOR LAMPS In order to avoid scratching the plastic lamps, do not use dry paper towels, non-approved chemical solvents or abrasive cleaners.
Cleaning CLEANING THE INSTRUMENT PANEL Clean the instrument panel with a damp cloth, then dry with a dry cloth. Avoid cleaners or polish that increase the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection. Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the air bag system.
Cleaning CLEANING LEATHER SEATS (IF EQUIPPED) All Ford, Lincoln and Mercury vehicles with leather seating surfaces have a clear, protective coating over the leather. To clean the leather seats, simply use a soft cloth with Deluxe Leather and Vinyl Cleaner (F2AZ-19521–WA). Dry the area with a soft cloth. It is recommended that you use the Deluxe Leather Care Kit (F8AZ-19G253–AA), available from your authorized Ford, Lincoln or Mercury dealer.
Cleaning FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your Ford, Lincoln or Mercury dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Each product is made from high quality materials that meet or exceed rigid specifications.
Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service. Check your Warranty Guide to find out which parts and services are covered.
Maintenance and Specifications Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front of the hood. 3. Lift the hood until the lift cylinders hold it open. IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L SOHC V8 engine 8 9 7 1.
Maintenance and Specifications 2. 3. 4. 5. 6. 7. 8. 9. Engine oil dipstick Engine oil filler cap Air filter assembly Power steering fluid reservoir Engine coolant reservoir Battery Windshield washer fluid reservoir Automatic transmission fluid dipstick WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. If the level is low, add enough fluid to fill the reservoir. In very cold weather, do not fill the reservoir all the way.
Maintenance and Specifications 2. Turn the engine off and wait up to 10 minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). DO NOT OVERFILL 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL.
Maintenance and Specifications • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter. • Do not overfill the engine with oil. Oil levels above this mark may cause engine DO NOT OVERFILL damage. If the engine is overfilled, some oil must be removed from the engine by a qualified service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2.
Maintenance and Specifications Engine oil and filter recommendations Look for this certification trademark. SAE 5W-20 engine oil is recommended. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). Use Motorcraft or an equivalent oil meeting Ford specification WSS-M2C153–H. SAE 5W-20 oil provides optimum fuel economy and durability performance meeting all requirements for your vehicle’s engine.
Maintenance and Specifications BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the scheduled maintenance guide for the service interval schedules. Keep the electrolyte level in each cell up to the “level indicator”. Do not overfill the battery cells.
Maintenance and Specifications When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners. Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing.
Maintenance and Specifications R TU LE AD RE If the battery has been disconnected or a new battery has been installed, the clock must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries.
Maintenance and Specifications When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the “cold fill level” or within the “cold fill range” as listed on the engine coolant reservoir (depending upon application). • Refer to the Scheduled Maintenance Guide for service interval schedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter.
Maintenance and Specifications The cooling system in your vehicle is filled with either green-colored Motorcraft Premium Engine Coolant meeting Ford specification ESE-M97B44–A or yellow-colored Motorcraft Premium Gold Engine Coolant meeting Ford Specification WSS-M97B51–A1. To determine your vehicle’s coolant type (color), check your coolant reservoir. • Add Motorcraft Premium Engine Coolant (green-colored), VC-4–A (U.S.
Maintenance and Specifications To avoid personal injury, make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come out forcefully when the cap is loosened slightly. 1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolant pressure relief cap on the coolant reservoir (an opaque plastic bottle).
Maintenance and Specifications Recycled engine coolant Ford Motor Company recommends the use of a recycled engine coolant produced by Ford-approved processes in vehicles originally equipped with Motorcraft Premium Engine Coolant (green-colored). However, not all coolant recycling processes produce coolant that meets Ford specification ESE-M97B44–A. Use of such coolant may harm the engine and cooling system components.
Maintenance and Specifications • NEVER decrease the coolant concentration below 40%. • Decreased engine coolant concentrations below 40% will decrease the corrosion protection characteristics of the engine coolant and may cause engine damage. • Decreased engine coolant concentrations below 40% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage.
Maintenance and Specifications Continued operation will increase the engine temperature: symbol will begin to flash. • The • A tone will sound 5 times. • The engine will completely shut down, causing steering and braking effort to increase. Once the engine temperature cools, the engine can be re-started. Take your vehicle to a service facility as soon as possible to minimize engine damage.
Maintenance and Specifications The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury.
Maintenance and Specifications • Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury. • Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin and/or clothing, promptly remove contaminated clothing and wash skin thoroughly with soap and water.
Maintenance and Specifications When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the filler cap counterclockwise 1/8 of a turn until it stops. 3. Pull to remove the cap from the fuel filler pipe. 4. To install the cap, align the tabs on the cap with the notches on the filler pipe. 5. Turn the filler cap clockwise 1/8 of a turn until it stops. The “Check Fuel Cap” light illuminates when the ignition is turned to the ON position.
Maintenance and Specifications Repairs to correct the effects of using a fuel for which your vehicle was not designed may not be covered by your warranty. Octane recommendations Your vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87. We do not recommend the use of (R+M)/2 METHOD gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes knocks lightly.
Maintenance and Specifications Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines to improve air quality. Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine. • Your “Service Engine Soon” indicator may come on.
Maintenance and Specifications The advertised capacity is the amount of the indicated capacity and the empty reserve combined. Indicated capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty. Empty reserve is the small amount of fuel remaining in the fuel tank after the fuel gauge indicates empty. The amount of usable fuel in the empty reserve varies and should not be relied upon to increase driving range.
Maintenance and Specifications 5. Follow one of the simple calculations in order to determine fuel economy: Multiply liters used by 100, then divide by total kilometers traveled. Divide total miles traveled by total gallons used. Keep a record for at least one month and record the type of driving (city or highway). This will provide an accurate estimate of the vehicle’s fuel economy under current driving conditions.
Maintenance and Specifications Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fuel economy. • Use recommended engine oil. Refer to Lubricant specifications in this chapter. • Perform all regularly scheduled maintenance items. Follow the recommended maintenance schedule and owner maintenance checks found in your vehicle scheduled maintenance guide.
Maintenance and Specifications EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. To make sure that the catalytic converter and other emission control components continue to work properly: • Use only the specified fuel listed. • Avoid running out of fuel. • Do not turn off the ignition while your vehicle is moving, especially at high speeds.
Maintenance and Specifications Please consult your Warranty Guide for complete emission warranty information. Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostics system. If your “Check Engine/Service Engine Soon” light is on, refer to the description in the Warning lights and chimes section of the Instrument Cluster chapter.
Maintenance and Specifications NG RI NOT DO ERFILL OV POW STE ER UI E FL D 3. Turn the engine off. 4. Check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is in this range. MAX MIN 5. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and MAX lines. Be sure to put the cap back on the reservoir.
Maintenance and Specifications Brake fluid is toxic. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes. Seek medical attention if irritation persists. If taken internally, drink water and induce vomiting. Seek medical attention immediately. If you use DOT 5 or any other brake fluid that is not DOT 3 or DOT 4, you will cause permanent damage to your brakes. Do not let the reservoir for the master cylinder run dry, this may cause the brakes to fail.
Maintenance and Specifications 7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated area for normal operating temperature or ambient temperature. Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the ambient temperature is above 10°C (50°F). DON’T ADD Correct fluid level The transmission fluid should be checked at normal operating temperature 66°C-77°C (150°F-170°F) on a level surface.
Maintenance and Specifications High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. DON’T ADD Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used.
Maintenance and Specifications 2. Release the clamps that secure the air filter housing cover. 3. Carefully separate the two halves of the air filter housing. 4. Remove the air filter element from the air filter housing. 5. Wipe the air filter housing and cover clean to remove any dirt or debris and to ensure good sealing. 6. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover.
Maintenance and Specifications U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
Maintenance and Specifications The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge.
Maintenance and Specifications Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification or Tire Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity. Use only the tire combinations recommended on the label.
Maintenance and Specifications Follow these guidelines when using snow tires and chains: • Use only cable type chains offered by Ford as an accessory or equivalent. Using SAE class S or other conventional link type chains may cause damage to the vehicle’s wheel house and/or body. • Install chains securely, verifying that the chains do not touch any wiring, brake lines or fuel lines. • Drive cautiously. If you hear the chains rub or bang against your vehicle, stop and re-tighten the chains.
Maintenance and Specifications REFILL CAPACITIES Fluid Engine oil (includes filter change) Brake fluid Power steering fluid Transmission fluid Engine coolant 2 4 Fuel tank Rear axle lubricant Windshield washer fluid 5 Ford Part Name Motorcraft SAE 5W-20 Super Premium Motor Oil Motorcraft High Performance DOT 3 Motor Vehicle Brake Fluid1 Motorcraft MERCONt ATF Motorcraft MERCONtV ATF Motorcraft Premium Engine Coolant (green-colored) or Motorcraft Premium Gold Engine Coolant (yellow-colored) N/A Motorc
Maintenance and Specifications 4 Add the coolant type originally equipped in your vehicle. Rear axles are considered lubricated for life when the vehicle is used for normal service. See your scheduled maintenance guide for Severe Duty requirements. 6 Add 118 ml (4 oz.) of Additive Friction Modifier C8AZ-19B546-A or equivalent meeting Ford specification EST-M2C118–A for complete refill of Traction-Lok rear axle. For limousine, use 2.4L (5.
Maintenance and Specifications Item Hinges, latches, striker plates, fuel filler door hinge and seat tracks Lock cylinders Power steering fluid Automatic transmission (4R70W)3 Rear Axle Lubricant 2 Windshield washer fluid Ford part name Multi-Purpose Grease Ford part number XG-4 or F5AZ-19G209-AA Ford specification ESB-M1C93-B or ESR-M1C159-A Penetrating and Lock Lubricant Motorcraft MERCONt ATF Motorcraft MERCONtV ATF Motorcraft SAE 80W-90 Premium Rear Axle Lubricant Ultra-clear Windshield Washer Conc
Maintenance and Specifications ENGINE DATA Engine Cubic inches Required fuel Firing order Spark plug gap Ignition system Compression ratio 4.6L SOHC V8 engine 281 87 octane 1-3-7-2-6-5-4-8 1.3-1.4 mm (0.052-0.056 inch) Coil on plug 9.4:1 VEHICLE DIMENSIONS Vehicle dimensions (1) Overall length (2) Overall width (3) Overall height (4) Wheelbase (5) Track - Front (5) Track - Rear a Denotes long wheel base mm (in) 5 469 (215.3)/5 621 (221.3)a 1 987 (78.2) 1 472 (58.0) 2 990 (117.7)/3 142 (123.7)a 1 611 (63.
Maintenance and Specifications 4 1 4 1 231
Maintenance and Specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the front door latch pillar on the driver’s side. Vehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel.
Maintenance and Specifications 1. World manufacturer identifier 2. Brake type and gross vehicle weight rating (GVWR) 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame and transfer case (if equipped).
Accessories FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for your vehicle through your local authorized Lincoln Mercury dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle. In addition, each accessory is made from high quality materials and meets or exceeds Ford’s rigorous engineering and safety specifications.
Accessories Comfort and convenience Cargo nets Cargo organizer Electrochromic compass mirror Electrochromic compass mirror with temperature display Engine block heaters HomeLinkt Remote start system Travel equipment Automatic headlamps with daytime running lights (DRL) Chrome wheel arch molding Daytime running lights (DRL) HomeLinkt Protection and appearance equipment Carpet floor mats Door edge guards First aid kit Flat splash guards Front end covers Highway safety kit Locking gas cap Molded splash guards
Accessories For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR or GAWR as indicated on the Safety compliance certification label). Consult your dealer for specific weight information.
Index A B Accessory delay ..........................62 Air bag supplemental restraint system ................................121, 125 and child safety seats ............123 description ......................121, 125 disposal ....................................128 driver air bag ..................123, 126 indicator light ...................12, 125 operation .........................123, 126 passenger air bag ...........123, 126 side air bag ..............................125 Air cleaner filter ............
Index in front seat ............................131 in rear seat ..............................131 Cleaning your vehicle engine compartment ..............187 exterior ....................................191 instrument cluster lens ..........190 instrument panel ....................190 interior .....................................190 plastic parts ............................189 safety belts ..............................191 washing ....................................186 waxing ............................
Index lubrication specifications ..................228, 230 refill capacities ........................227 service points ..........................194 starting after a collision .........157 Engine block heater .................139 Engine oil ..................................195 change oil soon warning, message center .......................195 checking and adding ..............195 dipstick ....................................195 filter, specifications ........198, 226 recommendations ...................
Index bulb specifications ....................54 daytime running lights .............49 flash to pass ..............................50 high beam ...........................15, 50 replacing bulbs .........................55 turning on and off ....................49 warning chime ..........................16 HomeLink universal transceiver (see Garage door opener) ..................................69–72 Hood ..........................................194 I Ignition ...............................
Index Load limits .................................150 GAWR ......................................150 GVWR ......................................150 trailer towing ..........................150 Locks autolock .....................................94 childproof ..................................88 doors ..........................................88 Lubricant specifications ...228, 230 Lumbar support, seats .............103 M Message center ...........................77 english/metric button ...............
Index lap belt ....................................114 Occupant Classification Sensor ......................................108 warning light and chime ...................12, 16, 115–116 Safety seats for children ..............................129–130 Seat belts (see Safety restraints) ..................................106 Seats ..........................................102 child safety seats ............129–130 cleaning ...................................190 easy access/easyout feature ..105 heated ........
Index W Warning chimes ...........................16 Warning lights (see Lights) .......10 Washer fluid ..............................195 Water, Driving through .............149 Windows power .........................................62 Windshield washer fluid and wipers checking and adding fluid .....195 checking and cleaning ..............59 operation ...................................59 replacing wiper blades .............60 Wrecker towing .........................
