LINDY LCD Terminal User Manual English LINDY No. 21520 - 21525 www.LINDY.
Safety Information • In order to avoid the risk of fire or electric shock, DO NOT expose this device to liquid or a high humidity environment • Operate the LCD only at temperatures between +5°C and +45°C • No user serviceable parts.
User Manual KVM LCD Terminal KVM LCD Terminal INSTALLATION INSTALLING THE DRAWER INTO A 19” CABINET 1. Fix the front side panel of the drawer onto the front side of your 19” cabinet 2. Fix the screws in the back onto the rear side of your 19” Cabinet. The mounting rails may be adjusted to fit different cabinet depths of between 52cm and 90cm Cable connections 1. 2. 3. 4. 5.
1 .L C D M o n ito r In s ta lla tio n 1-1 Installation: (1) The following process offers users the best way to set up your LCD Monitor into a whole PC system with correct and safe installation. (2) Turn off the power switch of the PC and disconnect from the mains input supply. (3) Connect one end of 15-pin XGA Signal Cable to the signal input port on the LCD Monitor and the other end to the signal output port of PC (4) Connect the DC 12V power output jack to the 12V DC input socket of the LCD monitor.
2 .F u n c tio n K e y s a n d o p e ra tio n : 2.1 Function Keys Definition and description: (1) Menu Key: Use this key to select and execute the magnitude and function process. The Sequence flows of Manu Key pressing: (a) Mode Selection: (+ Key) Press Manu key Display 1st press 2nd press 3rd press 4th press 5th press OSD *OSD shows up. Colour Picture Function Manu Mics Exit .
(2) (3) + Key: (a) In the Mode-Selection Mode: Pressing this key to locate forward the icon you want to adjust. Pressing it once, it moves one step forward to the next icon. Pressing it twice, it moves forward one more step to next 2nd icon. And so on. (b) Keep pressing down on this key, it flows continually through every icon and stops at the icon when the key is released. (c) In the Adjusting-and-executing Mode: The + Key, becomes the Adjusting-and-executing selection key.
(f) Keep pressing down on this key, and it will keep increasing continually until the key is released. (4) Switch (a) (b) (c) Power on/off Switch. Press this Key once; the monitor would be turned on. Press this key again and the monitor will be turned off.
2-2. Quick OSD Adjustment & Execution Operation: Key to be pressed Step 1 Menu Display OSD Display Remark Menu Key OSD Menu shows up. 1."Colour Icon” keeps flashing. 2.Mode is ready for Colour Adjustment. 3.
S e c tio n 1 : C o lo u r M o d e A d ju s tm e n t Key to be pressed Menu Display Magnitude Range Step 1 Example: Contrast Contrast: 0~255 Brightness: 0~216 Red Gain: 0~255 Menu Key Green Gain: 0~255 Blue Gain: 0~255 Contrast or Brightness/ Red/Green/ Blue by “+ key” Step 2 1. “Colour icon” keeps flashing. 2. “Contrast” marked by indigo light. Example: Contrast Menu Key Step 3 +/- key 1. “Colour icon” keeps flashing. 2. “Contrast” marked by indigo light. 3. Adjusting scale of 0~255 shows up.
Step 4 Example: Contrast Menu Key The Contrast adjustment is completed. The system is ready for next selection Step 5 +/- key To select Brightness 1. “Colour icon” keeps flashing. 2. “Contrast” marked by indigo light. Example: Brightness If selects: Red, Green, Blue. Repeat step 3~ 5 to complete the adjustment. 1. “Colour icon” keeps flashing. 2. “Brightness” on indigo light. Step 6 Example: Brightness Manu Key 1. “Colour icon” keeps flashing. 2. “Brightness” on indigo light. 3.
Step 7 Example: Brightness +/- key 1. “Colour icon” keeps flashing. 2. “Brightness” on indigo light. Example: Brightness Step 8 * Keeps press the “+ key”: Value in the Scale is increasing until 216 * Keeps press the “- key”: Value in the Scale is decreasing until 0 Release the key, the value will stop at the satisfied point. Manu key Brightness adjustment is completed. The system is ready for next selection 1. “Colour icon” keeps flashing. 2. “Brightness” on indigo light.
Step 10 Example: Exit Manu key System backs to Mode Selection Status and is ready to select: 1. “Colour icon” keeps flashing. Step 11 +/- key Section 2 or Section 3 or Section 4 or Section 5 or Section 6 The selected icon become flashing.
S e c tio n 2 : Im a g e M o d e A d ju s tm e n t Key to be pressed Menu Display Magnitude Range Step 1 Example: H-Position H-Position: 0~146 V-Position: 0~20 Sharpness: 1/2/3/4/5 Menu Key Phase: 0~31 Clock: 0~127 H-Position or V-Position/ Sharpness/ Phase/Clock by “+ key” Step 2 3. “Image icon” keeps flashing. 4. “H-Posit.” marked by indigo light. Example: H-Position Menu Key Step 3 +/- key 4. “Image icon” keeps flashing. 5. “H-Posit.” marked by indigo light. 6. Adjusting scale of 0~146 shows up.
Step 4 Example: H-Position Menu Key H-Position adjustment is completed. The system is ready for next selection 3. “Image icon” keeps flashing. 4. “H-Posit.” marked by indigo light. Example: V-Position Step 5 +/- key To select V-Position 3. “Image icon” keeps flashing. 4. “V-Position” on indigo light. Step 6 Example: V-Position Manu Key 4. “Image icon” keeps flashing. 5. “V-Position” on indigo light. 6.
Step 7 Example: V-Position +/- key 3. “Image icon” keeps flashing. 4. “V-Position” on indigo light. Example: V-Position Step 8 * Keeps pressing “+ key”: Value in the Scale is increasing until 20 * Keeps pressing “- key”: Value in the Scale is decreasing until 0 Release the key, the value will stop at the satisfied point. Manu key V-position adjustment is completed. The system is ready for next selection 3. “Image icon” keeps flashing. 4. “V-Position” on indigo light.
Step 10 Example: Exit Manu key System backs to Mode Selection Status and is ready to select: 1. “Image icon” keeps flashing. Step 11 +/- key Section 1 or Section 3 or Section 4 or Section 5 or Section 6 The selected icon become flashing.
S e c tio n 3 : F u n c tio n E x e c u tio n Key to be pressed Step 1 Menu Display Example: Auto Configuration Remark Manu pressed and Display: Auto Config. Menu Key Selected by +/- key: Auto Position. Auto Phase. Auto Clock. Auto Balance. Exit Auto config 5. “Function icon” keeps flashing. 6. “A. Config” marked by indigo light. Step 2 Example: Auto Configuration Menu Key 7. “Function icon” keeps flashing.. 8. Yes/No execution shows up.
Step 4 Example: Auto Configuration Menu Key Auto Config. is completed. The system is ready for next selection 5. “Function icon” keeps flashing. Step 5 Example: Auto-Position +/- key To select Auto-Position Step 6 1. “Function icon” keeps flashing. 2. “Auto position” Marked on Indigo light. Example: Auto-Position Manu Key 7. “Function icon” keeps flashing. 8. Yes/No execution shows up. 16 If selects: Auto Phase, Auto Clock or Auto Balance: Repeat step 3~ 5 to execute.
Step 7 Example: Auto-Position * Presses “+ key” to select “Yes.” * Presses “- key” to select “No.” +/- key “Function icon” keeps flashing. Example: Auto-Position Step 8 Manu key Auto-Position execution is completed. The system is ready for next selection “Function icon” keeps flashing. Example: Exit Step 9 +/- key To select Exit 5. “Fuction icon” keeps flashing. 6. “Exit” marked on indigo light. 17 As for Auto Phase, Auto Clock or Auto Balance: Repeat step 5~ step 8.
Step 10 Example: Exit Manu key System backs to Mode Selection Status and is ready to select: “Function icon” keeps flashing. Step 11 +/- key Section 1 or Section 2 or Section 4 or Section 5 or Section 6 The selected icon become flashing.
S e c tio n 4 : O S D M a n u A d ju s tm e n t Key to be pressed Step 1 Menu Display Example: Language Remark Manu pressed and Display: Language Menu Key Selected by +/- key: OSD H-Position. OSD V-Position. OSD Timer. Exit Language 7. “OSD Manu icon” keeps flashing. 8. “Language” marked by indigo light Step 2 Example: Language Menu Key Language Table: English. Germany. France. Spanish Italy 9. “OSD Manu icon” keeps flashing.. 10. Language table shows up.
Step 4 Example: Language Menu Key Language setting is completed. The system is ready for next selection 6. “OSD Manu icon” keeps flashing. Step 5 Example: OSD H-Position +/- key To select OSD H-Position Step 6 3. “OSD Manu icon” keeps flashing. 4. “OSD H-position” Marked on Indigo light. Example: OSD H-Position Manu Key 9. “OSD Manu icon” keeps flashing. 10. Adjusting Scale of 0~120 shows up. 20 Adjusting Range: OSD Position: H-Position: 0~120 V-position: 0~ 120 If selects: OSD V-Position.
Step 7 Example: OSD H-Position +/- key * Keeps presses “+ key”: Value in the Scale is increasing until 120 * Keeps presses “- key”: Value in the Scale is decreasing until 0 Release the key, the value will stop at the satisfied point. “OSD Manu icon” keeps flashing. Example: OSD H-Position Step 8 Manu key OSD H-Position adjustment is completed. The system is ready for next selection. “OSD Manu icon” keeps flashing. Example: Exit Step 9 +/- key To select Exit 7. “OSD Manu icon” keeps flashing. 8.
Step 10 Example: Exit Manu key System backs to Mode Selection Status and is ready to select: “OSD Manu icon” keeps flashing. Step 11 Section 1 or Section 2 or Section 3 or Section 5 or Section 6 The selected icon become flashing.
S e c tio n 5 : F u n c tio n E x e c u tio n Key to be pressed Menu Display Remark Step 1 Example: Input Source Manu pressed and Display: Input Source. Menu Key Selected by +/- key: Mode Option. Reset. Exit Input Source 9. “Misc icon” keeps flashing. 10. “Input Source” marked by indigo light. Example: Input Source Step 2 Menu Key 11. “Misc icon” keeps flashing.. 12.
Step 4 Example: Input Source Menu Key Input Source Selection is completed. The system is ready for next selection. “Misc icon” keeps flashing. Step 5 Example: Mode Option +/- key To select Mode Option 5. “Misc icon” keeps flashing. 6. “Mode Option” Marked on Indigo light. Step 6 Example: Mode Option Manu Key 11. “Misc icon” keeps flashing. 12. MAC 768-75/VESA768-75 shows up. 24 If selects: Reset. Repeat step 3~ 5 to execute.
Step 7 Example: Mode Option * Presses “+ key” to select “MAC768-75.” * Presses “- key” to select “VESA768-75” +/- key “Misc icon” keeps flashing. Example: Mode Option Step 8 Manu key Mode Option selection is completed. The system is ready for next selection Step 9 “Misc icon” keeps flashing. Example: Exit +/- key To select Exit 9. “Misc icon” keeps flashing. 10. “Exit” marked on indigo light. 25 As for Reset Repeat step 5~step 8.
Step 10 Example: Exit Manu key System backs to Mode Selection Status and is ready to select: “Misc icon” keeps flashing. Step 11 +/- key Section 1 or Section 2 or Section 3 or Section 4 or Section 6 The selected icon become flashing.
S e c tio n 6 : O S D E x it Key to be pressed Menu Display Example: Exit Mode Selection: E x it 11. “Exit icon” keeps flashing. 12. Only “Exit” displayed on OSD.
3 .S p e c ific a tio n a n d A p p e n d ix : 3-1 Technical Specification: LCD Panel: 15.0” TFT, 0.297mm, TTL Viewing Angle -60~60 degree (H), -55~45 degree (V) Resolution: Display Colors: 1024 x 768 (XGA) 800 x 600 (SVGA) 640 x 480 (VGA) 16.7 M (8 bits/color) Pixel Pitch (mm): 0.297 (H) x 0.297 (V) Contrast Ration: 350:1 Brightness (cd/m2): 250nit Display Area (mm): 304.1 (H) x 228.1 (V) Power Supply: AC 90~264, 50~60Hz Universal Power management: VESA-DPMS 30W Max.
3-2. Appendix A: Systems Compatible: Input Mode XGA SVGA VGA DOS (Text) DOS (EGA) TEXT MAC NTSC PAL Resolution 1024 x 768 800 x 600 640 x 480 640 x 480 640 x 350 720 x 400 832 x 624 720 x 240(I) 720 x 288 (I) Zoom to 1024x768 1:1 HQ scale up HQ scale up Scale up Scale up Scale up HQ scale up De-interlace De-interlace 3-3: Appendix B: Modes supported , - . / 0 1 2 3 4 ! " #$ % 3 .
Radio Frequency Energy Certifications Shielded cables must be used with this equipment to maintain compliance with radio frequency energy emission regulations and ensure a suitably high level of immunity to electromagnetic disturbances. European EMC Directive 89/336/EEC CE statement This equipment complies with the requirement for CE mentioned in the European Directive and Standards EN55022 and EN55024.