User Manual

Scene Folders
YourM9isequippedwith4scenefoldersgivingyouatotalof24scenes.
To access a new folder press 3A + Tap to access your current scenes
folderthenturntheModelSelectknobandselectthefolderyouwish
toload(1-4)thenpressanyscenetoloadit.Sceneswillnowdefaultto
the new folder.
LoopeR & setup
TheLooperintheM9gives youup to28secondsofmonorecording
timeatnormalspeed,or56secondsathalfspeed.Yourloopwillalways
runinmono,evenifyou’rerunningstereoFX.
To begin, press and hold the
TAP/Hold for Looper footswitch.
Your
TAPLEDwillnowstayon.WheninLoopmodeyoucan
still use
TAPtosetFXtempoandspeed-youjustwon’thavethe
LEDashingintimeforreference.
Press
REC/ODUB to start recording your loop. You can press
REC/ODUB again to immediately end your loop and begin
recordingasmanyoverdubsasyou’dlike,or...
Press
PLAY/STOP to continue the loop without recording. You
canstilljamoveryourloop.Itjustwon’tbeoverdubbedintoyour
loop. Press again to stop the loop playback.
PLAY ONCE can be pressed from stop or during playback, to
cause play to end when the loop completes.
Hitabadnote?Youcanpress
UNDO/REDO to discard your last
overddub. This is also handy if you just want to remove your last
overdub momentarily. Press
UNDO/REDO again to recall the
discarded overdub.
Stepon
HALF SPEED while in playback mode and your loop
willnowplaybackinhalfspeed.Startanewloopinhalfspeed
whenyouneedadditionallooptime-upto56seconds.
The
REV footswitch sets your playback to reverse. Reverse can-
not be engaged during record - doing so will immediately stop
recording and start playback of your loop in reverse.
Press and hold
TAPtoexitLoopMode.
Using FX while looping
Any effects you have on when entering Looper mode will remain in
your signal path. To change your FX Units or Switch Scenes during
looping press and hold
TAP to exit loop mode, make your selections and
then press and hold
TAPtoreturntoLoopmode.Settingyourlooper
to “
PRE”willapplyFXtoyourguitarsignalonly.IntheSetupMenu
setting the looper to “
POST”willapplyFXtoyourlooprecordingand
your guitar signal.
Looper Setup
ToviewandeditsetupoptionsforyourLooperfunctionalityyou’llneed
to access the setup screen. First, make sure you are in normal opera-
tion - if you are currently in looper mode press and hold
TAP to exit.
Nowsimultaneouslypress
1B + 2B to enter setup then press the model
encoder until you see this screen:
OVERDUB LO CUT
HI CUT
PLAY
Looper: Levels EQ
LPR PRE
Yourbottomleftknobswitchesyourlooper’saudiopathfromPre(your
looperbeforeFXUnits)toPost(afterFXUnits).
PLAY adjusts the level
of your loop.
OVERDUB adjusts the level of each overdub pass from
0dBto-20dB.
LO CUT and HI CUTeqltersaffectyourrecordedand
looped audio only.
DetaiLs
Constant Memory
As you adjust an effect (say, a Screamer distortion running in effect
memory
A of FX Unit 1), those adjustments are retained as you switch
away to a different
A/B memory and back again—no save function is