Owner manual

 isnotcurrentlydisplayedsimplydoubletaptheMemoryFootswitchyou
would like to edit, or press and hold
TAP and quickly press the MODEL
SELECTknobtoscrollthroughactiveFXUnits.
4. Model Select - Press in the knob to select an effect type (Delay,
Modulation,Distortion,FilterorReverb)youwant.Thenturntheknob
to scroll through available effect models.
5. Parameter Knobs - Usetheseknobstoeditcurrenteffectsettingsshown
in your display. These knobs usually control the setting locations as
shown in the diagram to your left.
6. TAP - Tapyourtempoontheswitchafewtimestosetthetime/speed/
tempo of all
TAP enabled effects.
sCenes & sCene setup
YoucanrunyourM9StompboxModelerinSceneSelectModegiving
you6 scenes, each of which is a complete pedalboard, storing all the
settings of the A/B memories of the 3 FX Units. We’ve loaded each
scene with an example pedalboard, to get you inspired.
Select
Scene
PRESS TAP
TO CANCEL
ToaccessyourScenes,simultaneouslypress3A + Tap. Your display will
nowlooksimilartothedisplayshownabove.The6Scenesaredisplayed
asA&Bforeachofthe3FXrows.ThecurrentlyactiveSceneisshown
in the solid circle (
FX2 Unit A in the example above). To select a differ-
entScene,pressanyoftheother5FXUnitFootswitches.Momentary
SceneModeisthedefaultsetting,soselectinganewsceneputsyouright
into a whole new pedal board where you can turn effects off and on.
Choosing Momentary or Latch Scene Modes
Simultaneously press 1B + 2B to enter setup then press
the model encoder until you see this screen:
MOMEN
1>2>3
MNL SAVE
Prefs Scenes
DSP BYP
SCENE
REL
DIM ON
POTS
Useyourparameterknob(bottomcenter)toselectbetweenMomentary
(
MOMEN SCENE) or Latch (LATCH SCENE).Whenyouaredone,
simultaneously press
1B + 2B to exit setup.
Momentary Scene Mode
InMomentarySceneMode,onceyouselectanewSceneyourdisplay
will then return to the basic view displaying the current settings of the
rstactiveFXUnitinyourchain.Youcannowactivateorbypassany
FX Unit if you would like. Any changes you make to the Scene will
automatically be saved, just like a traditional pedalboard setup. To select
anew Scene, simultaneously press
3A + TAP, thenpressanyAorB
footswitch.
Latch Scene Mode
InLatchSceneMode,theonlydifferenceiswhenyouaccessyourScenes
(
3A + TAP),the6Scenesremainonthedisplayafteryouloadanew
Scene-youwon’tseeFXUnitsettingsintheLCD.
This mode is exceptionally handy when you want to switch from one set
of multiple effects to another. You can tweak individual effects in Latch
modebysimplypressing3A+Taptotoggleoutofscenemode.Afteryou
aredonetweakingjustpress3A+Tapagain.
Scene Save
TosaveyourcurrentsetofFXUnitssettingstoasceneortocopyyour
currentlyloadedScene,pressandhold
3A + TAP until the following
screen appears:
Save
To:
PRESS TAP
TO CANCEL
Nowpressthefootswitchofthedesiredlocationyou’dliketosaveyour
scene to. Your display should now read “
Save Completed” for 2 seconds
thenreturntonormaloperationforthemodeyourScenesaresetto.