User Manual
Table Of Contents
- HX Stomp XL 3.0 Owner's Manual
- Welcome to HX Stomp XL
- Quick Start
- Play View
- Edit View
- Selecting Blocks/Adjusting Parameters
- Bypassing a Block
- Bypassing HX Stomp XL Completely
- Choosing a Block’s Model
- Moving Blocks
- Copying/Pasting a Block
- Clearing a Block
- Clearing All Blocks
- Adding a Block to Favorites
- Saving a Model’s Default Settings
- Saving/Naming a Preset
- Creating /Restoring Full Device Backups
- Serial vs. Parallel Routing
- Setting Path B’s Output
- TAP Tempo
- The Tuner
- Dynamic DSP
- Block Order and Stereo Imaging
- The Blocks
- Snapshots
- Bypass Assign
- Controller Assign
- Command Center
- Global EQ
- Global Settings
- USB Audio
- MIDI
- Additional Resources
14
Snapshot Footswitch Mode
Similar to the snapshots feature in some high-end digital mixers, each of the four
snapshots in HX Stomp XL stores and recalls the state of certain elements in the current
preset, including:
• Block Bypass—The bypass (on/o) state of all processing blocks (except
Looper), independent of any footswitch assignments. Also, see “Using
Snapshots” on page 42
• Parameter Control—The values of any parameters assigned to controllers (up
to 64 per preset). Also, see “Using Snapshots” on page 42
• Command Center—The values of any instant MIDI CC, Bank/Prog, MMC, HX
Preset, HX Snapshot, and HX Looper messages, plus the state (dim or lit) of any
CC Toggle messages. Also, see “Command Center” on page 50
• Tempo—The current system tempo, if “Global Settings > MIDI/Tempo” > Tempo
Select is set to “Per Snapshot.” (By default, it’s set to “Per Preset.”)
1. Press and release the and switches simultaneously to
enter Snapshot mode.
Thefoursnapshotsash,indicatingoneisreadytobeselected.
01A
FX:Stereo Swirl
1
BANK
BANK
EDIT / EXIT
TUNER
TAP
MODE
B
D
A
C
1
2
43
2. Press one of the four snapshot switches to select it.
ToexittheashingSnapshotselectstatewithoutchangingsnapshots,pressthe
MODE (Edit/Exit) switch.
NOTE: Snapshots are powerful enough to warrant their own chapter. See
“Snapshots” on page 42.
NOTE: If you don’t want Snapshot footswitches to disappear after selecting one,
set the “Global Settings > Footswitches” > Snapshot Mode parameter to “Latch.”
In this case, HX Stomp XL stays in Snapshot footswitch mode until you press
MODE (Edit/Exit).
Pedal Edit Mode
Youcaneditmostblocks’settingswithouttakingyourhandsotheguitar,including
Amp, Eect, Cab, IR, Split, Mixer, Input, and Output Block parameters! If you hate
having to reach down and twist knobs, Pedal Edit mode will be your new best friend.
Although Pedal Edit is not intended to replace proper controller assignment, it can also
be used to tweak one parameter at a time during a performance in a pinch.
1. Press and hold the MODE switch for one second to enter Pedal
Edit mode’s Block Select screen.
If the current preset’s signal ow includes six or fewer blocks (including the
Input, Split, Merge, and Output), each block’s label appears—independent of its
footswitchassignment—ashingonthescreenalongwiththefootswitches.
If the signal ow has seven or more blocks (including the Input, Split, Merge,
and Output), FS3 appears as MORE... (as shown below). Pressing FS3 (MORE...)
cycles through the additional page(s) of blocks. The preset’s processing blocks
appear,withtheirrespectivefootswitch1~6LEDsashing.
EDIT / EXIT
TUNER
TAP
MODE
B
D
A
C
01A
FX:Stereo Swirl
1
Stupor
OD
Weeper
MORE...
Simple
Pitch
Tremolo/
Autopan
Multi
Pass
NOTE: Selecting a block in Pedal Edit mode does not correlate with any
footswitch assignment it may have.