User Manual
Table Of Contents
- HX Stomp XL 3.0 Owner's Manual
- Welcome to HX Stomp XL
- Quick Start
- Play View
- Edit View
- Selecting Blocks/Adjusting Parameters
- Bypassing a Block
- Bypassing HX Stomp XL Completely
- Choosing a Block’s Model
- Moving Blocks
- Copying/Pasting a Block
- Clearing a Block
- Clearing All Blocks
- Adding a Block to Favorites
- Saving a Model’s Default Settings
- Saving/Naming a Preset
- Creating /Restoring Full Device Backups
- Serial vs. Parallel Routing
- Setting Path B’s Output
- TAP Tempo
- The Tuner
- Dynamic DSP
- Block Order and Stereo Imaging
- The Blocks
- Snapshots
- Bypass Assign
- Controller Assign
- Command Center
- Global EQ
- Global Settings
- USB Audio
- MIDI
- Additional Resources
18
Choosing a Block’s Model
1. If not already there, press VIEW to select Edit view.
2. Turn the Upper Knob to select the desired block, then turn the
Lower Knob to change its model.
To create a new block, turn the Upper Knob to select an empty
location and then turn the Lower Knob.
Selecting models within the same category can be very quick. However, as HX
Stomp XL has hundreds of items to choose from, using this method to, say,
change a mono Distortion block (beginning of the list) into a Looper block (end of
the list) is very slow. Instead, you should open the model list:
3. Press the Lower Knob to open the model list:
CATEGORY SUBCATEGORY MODEL
Category
EQ
Modulation
Delay
Reverb
Pitch/Synth
Delay
Mono
Stereo
Legacy
Delay
Transistor Tape
Cosmos Echo
Harmony Delay
Bucket Brigade
Adriatic Delay
Mostmodelcategoriesincludesubcategories.Forexample,eectsinthe“Mono”
and “Stereo” subcategories are HX (Helix) models. Eects in the “Legacy”
subcategory are taken from the classic Line 6 M13
®
, M9
®
, M5
®
, DL4™, MM4™,
FM4™, and DM4™ pedals. Amp+Cab and Amp models have Guitar and Bass
subcategories. Cab models have Single and Dual subcategories.
NOTE: Therstcategoryinthelist,Favorites,isinitiallyempty,awaitingyouto
addamp,cab,and/oreectsmodels,includingyourowncustomsettingsand
assignments—see “Adding a Block to Favorites” on page 19.
Turn the Lower Knob to select items in a list.
Press the Lower Knob (or PAGE ) to view a category or
subcategory’s contents.
Press PAGE to go back one level.
NOTE:Eectsblockswithstereoorlegacymodelsdisplaysmalliconstothe
right of the model name:
MONO STEREO LEGACY
Courtesan Flange
7.1 5.34.3
Courtesan Flange
7.1 5.34.3
Analog Flanger
33% 88%0.055Hz
IMPORTANT! If you encounter items in the list that are grayed out or
unavailable, this means the preset cannot accommodate that category,
subcategory, or model. See “Dynamic DSP”.
4. Using the Lower Knob, PAGE, and PAGE , select the desired
category, subcategory, and model.
SHORTCUT: To quickly skip through model subcategories, without ever
having to open the model list—From Edit view, press and turn the Lower
Knob to skip subcategories, then turn normally to select models within that
subcategory
5. To close the model list, select an item in the far right column
and press the Lower Knob again (or press to cancel).
Moving Blocks
1. If not already there, press VIEW to select Edit view.
2. Turn the Upper Knob to select any block (other than Input or
Output) and press ACTION.
The block appears “picked up,” and the action panel appears.
Harmony Delay
Copy
Block
B
Path
Paste
Block
Turn to move
3. Turn the Upper Knob to move the block.
4. Press ACTION again (or ) to close the action panel.
NOTE: To move a block between parallel paths A and B, press ACTION and then
turn Knob 1 - See “Serial vs. Parallel Routing”.