User Manual
Table Of Contents
- HX Stomp XL 3.0 Owner's Manual
- Welcome to HX Stomp XL
- Quick Start
- Play View
- Edit View
- Selecting Blocks/Adjusting Parameters
- Bypassing a Block
- Bypassing HX Stomp XL Completely
- Choosing a Block’s Model
- Moving Blocks
- Copying/Pasting a Block
- Clearing a Block
- Clearing All Blocks
- Adding a Block to Favorites
- Saving a Model’s Default Settings
- Saving/Naming a Preset
- Creating /Restoring Full Device Backups
- Serial vs. Parallel Routing
- Setting Path B’s Output
- TAP Tempo
- The Tuner
- Dynamic DSP
- Block Order and Stereo Imaging
- The Blocks
- Snapshots
- Bypass Assign
- Controller Assign
- Command Center
- Global EQ
- Global Settings
- USB Audio
- MIDI
- Additional Resources
40
Split
A Split block appears any time a parallel path is created but is visible only when selected:
HX Stomp XL includes four dierent types of Split blocks—Y, A/B, Crossover, and
Dynamic.
Turn the Upper Knob to select the Split block and then turn the
Lower Knob to change the Split type.
Split > Y Settings
Knob
Parameter Description
1 Balnce A
Adjusts the stereo balance (pan) of the signal sent to Path A
(upper).
2 Balnce B
Adjusts the stereo balance (pan) of the signal sent to Path B
(lower).
TIP: Okay, this one’s for the power users: If you move a Split > Y block all the
way left, set its BalnceA to “L100” and its BalnceB to “R100,” you can process
the L/MONO and RIGHT inputs independently. In addition, if you route the Mixer
block to Path B (Send L/R), you can process two instruments simultaneously,
each with its own mono input, stereo processing, and stereo outputs!
Split > A/B Settings
Knob Parameter Description
1 RoutTo
Determines the amount of the signal sent to Path A vs. Path B.
Press the knob to set to Even Split.
Split > Crossover Settings
Knob Parameter Description
1 Freq
AnysignalabovethisfrequencyissenttoPathA(upper);any
signal below this frequency is sent to Path B (lower).
2 Revrse
When on, reverses the path assignments (any signal above the
crossover frequency is sent to Path B, any signal below the
crossover frequency is sent to Path A).
Split > Dynamic Settings
Page Knob Parameter Description
1
1 Threshold
Any signal below the Threshold volume level is routed
toPathA;anysignalabovetheThresholdisroutedto
Path B.
2 Attack
Determines how fast the signal is routed to Path B
once reaching the Threshold.
3 Decay
Determines how fast the signal returns to Path A once
falling below the Threshold.
2 1 Reverse
When on, reverses the path assignments (any signal
above the Threshold value is sent to Path B, any signal
below the Threshold value is sent to Path A).
NOTE:MuchlikeanyEectstypeblock,aSplitblockcanbebypassed,aswellas
have a bypass assignment created for it. When bypassed, regardless of the Split
type in use, the block sends both left and right signals to both paths equally.
Mixer
A Mixer block appears any time a parallel path is created but is visible only when
selected:
Mixer Settings
Page Knob Parameter Description
1
1 A Level
Adjusts the output level of Path A (upper).
2 A Pan
Adjusts the left/right stereo balance of Path A.
3 B Level
Adjusts the output level of Path B (lower).
2
1 B Pan
Adjusts the left/right stereo balance of Path B.
2 B Polari
Inverts the polarity of Path B. Typically, this should be set
to “Normal.”
3 Level
Adjusts the overall output level of the Mixer block.