User Manual

43
NOTE: If you don’t want Snapshot footswitches to disappear after selecting
one, set “Global Settings > Footswitches” > Knob 4 (Snapshot Mode Switches)
to “Latch.” In this case, HX Stomp XL stays in Snapshot footswitch mode until
you press MODE (Edit/Exit).
Alternatively, press the PRESETS knob and turn Knob 2 (Select Snapshot).
NOTE: If you select a snapshot that hasn’t yet been altered, it appears the
same as the snapshot you came from. As soon as you edit a new snapshot
(say,byenablingorbypassinganamporeectblock),thesnapshotbecomes
“active” and remembers any changes.
3. Adjust the preset by doing one or more of the following:
• Turn one or more eects on or o by pressing stomp mode footswitches or
pressing the Upper Knob in “Edit View”. Snapshots remember every block’s
on/ostate (or youcan change this behavior—see “Snapshot Block Bypass
On/O”).
• To adjust a parameter AND have it automatically update per snapshot,
press and turn the knob.Snapshotsrememberthevaluesofupto64eects
parameters. The parameter’s value appears white, indicating a controller is
assigned to it—in this case, the Snapshots controller:
Harmony Delay
FeedbkTime
37%
Mix
35%1/8
• On the Command Center page, adjust the Instant messages’ values or
press a footswitch assigned to CC Toggle, Ext Amp, Qwerty Hotkey, or HX
Looper. These Command Center assigned messages are sent when recalling a
snapshot—also see “Command Center”
SHORTCUT: Hold ACTION and press a parameter knob to quickly remove
any controller assignment (including the Snapshots controller). The value
appears in color, indicating no controller is assigned to it.
NOTE: You can also manually assign the Snapshots controller. From the
“Controller Assign” page, select the desired block and parameter and turn
Knob 2 (Controller) to select “Snapshot.”
4. Switch back to the snapshot you started with.
HX Stomp XL instantly and seamlessly returns to its previous state.
NOTE: If you’ve changed “Global Settings > Preferences” > Snapshot Edits
to“Discard,”youmustsavethepresetbeforeselectingadierentsnapshot;
otherwise, any edits will be discarded!
Snapshot Reselect
The “Global Settings > Preferences” > Snapshot Reselect parameter adds even more
exibilitytotheSnapshotmodefootswitches.Asanexample,sayyou’replayingalong
on Snapshot 2 (VERSE), then you press the Snapshot 3 (CHORUS) to load it. What
should happen if you press the Snapshot 3 footswitch again? With Snapshot Reselect
set to the default “Reload,” Snapshot 3 is simply reloaded again. But when set to
“Toggle,” it will now load the previously loaded snapshot (Snapshot 2, in this example)—
and successive presses of the Snapshot 3 footswitch then continues to toggle between
Snapshot 2 and Snapshot 3.
Snapshot Block Bypass On/Off
There may be situations where you don’t want snapshots to control a particular block’s
bypassstate;thatis,you’dprefertoturnitonandomanually.Forexample,youmay
want manual control of a Boost block at any time without worrying whether a particular
snapshotmightturnitonoro.
1. Within the Edit view screen, select a processing block within
the signal ow and press ACTION.
2. Press PAGE once and turn Knob 3 (Snapshot Bypass) to set
the behavior for the block.
Harmony Delay
FS2 Latching
TypeSwitch
Clear
Block
Clear All
Blocks
Snapshot
Bypass
On
By default, all blocks are set to”On,” so that snapshots automatically control their
bypassstate.Changeto“O”todisablesnapshotcontroloftheselectedblock’s
bypass state.