User Manual

52
HX Preset, Snapshot, and Looper Commands
These“HX”commandsallowyoutocongureStompmodeswitchesforevengreater
control of your device’s internal functions. HX commands can be assigned on HX Stomp
XL using the preceding steps (see “Assigning a Command”). All assignments are saved
per preset.
NOTE: Although Stomp mode switches can be assigned to multiple functions,
to avoid unintended behavior, we strongly recommend the HX Preset, HX
Snapshot, and HX Looper commands are assigned only to empty footswitches.
HX Preset
The HX Preset command allows you to congure a Stomp mode footswitch to
immediately “jump to” any other preset.
HX Preset
Knob Parameter Description
2 Preset
Sets the preset to be selected by the command: Next,
Previous, or a preset’s number (01A~32D).
HX Snapshot
TheHXSnapshotcommandallowsyoutocongureaStompmodefootswitchtorecall
any snapshot within the current preset immediately.
1. From the Command Center page, select a footswitch and turn
Knob 1 (Command) to “Snpsht.”
2. Turn Knob 2 (Behavior) to either “Prs/Rel” (Press/Release) or
“Prs/Hld” (Press/Hold)
3. Turn the other two knobs to congure which snapshots are
recalled per the “Press” and the “Release” (or “Hold”) of the
footswitch, respectively.
HX Snps (Snapshots)
Page Knob Parameter Description
1
2 Behavior
Sets the behavior for the footswitch. This allows
you to recall the desired snapshot index number, or
Next or Previous snapshot, independently per each
Press and Release, or each Press and Hold of the
footswitch. (Note that the assigned, Stomp mode
footswitch’s label and LED will only indicate the
command assigned to the Press function.)
3 Press
Sets the snapshot to be recalled on the Press action
of the footswitch.
HX Snps (Snapshots)
Page Knob Parameter Description
2 1
Release/
Hold
Sets the snapshot to be recalled on the Release (or
Hold, depending on your page 1, knob 2 selection) of
the footswitch.
HX Looper
ForapresetthatincludesaLooperblock,thiscommandallowsyoutocongurean
Instant or Stomp mode footswitch to trigger any function of the Looper.
NOTE: A Looper block must be present in your preset for HX Looper
commands to function.
HX Looper - Instant Command Assignment:
1. In the Command Center window, select an Instant command
controller and turn Knob 1 (Command) to “Looper.”
2. Turn Knob 2 (Function) to choose the specic Looper function
you wish to trigger.
The selected Function action is automatically stored and recalled per snapshot.
Thisallowsyoutorecordaloopand,forexample,congureanInstantcommand
to automatically “Play” the Loop when loading one Snapshot and “Stop” when
loadingadierentSnapshot.
HX Loop (Looper) - Instant Command
Knob Parameter Description
2 Function
Sets the Looper action to be triggered: Play, Stop, Play/
Stop, Rec, Overdub, Record/Overdub, Play Once, Reverse,
Forward, Reverse/Forward, Half Speed, Full Speed, Toggle
Speed, or Undo.
HX Looper - Footswitch Assignment:
1. In the Command Center window, select a footswitch and turn
Knob 1 (Command) to “Looper.”
2. Turn Knob 2 (Behavior) to either “Prs/Rel” or “Prs/Hld.”
3. Turn the other knobs to congure which Looper commands
are sent per the “Press” and the “Release” (or “Hold)” of the
footswitch, respectively.
The selected Behavior, Press, and Release/Hold actions are automatically
stored and recalled per snapshot.