Datasheet

ManualsBrandsLINEAR TECHNOLOGY ManualsLinear ICsLinear IC - Op-amp Multi-purpose SO 8

LT1013/LT1014

10134fd

Typical applicaTion

DescripTion

Quad Precision Op Amp (LT1014)

Dual Precision Op Amp (LT1013)

The LT

1014 is the ﬁrst precision quad operational ampliﬁer

which directly upgrades designs in the industry standard

14-pin DIP LM324/LM348/OP-11/4156 pin conﬁguration.

It is no longer necessary to compromise speciﬁcations,

while saving board space and cost, as compared to single

operational ampliﬁers.

The LT1014’s low offset voltage of 50µV, drift of 0.3µV/°C,

offset current of 0.15nA, gain of 8 million, common mode

rejection of 117dB and power supply rejection of 120dB

qualify it as four truly precision operational ampliﬁers.

Particularly important is the low offset voltage, since no

offset null terminals are provided in the quad conﬁguration.

Although supply current is only 350µA per ampliﬁer, a new

output stage design sources and sinks in excess of 20mA

of load current, while retaining high voltage gain.

Similarly, the LT1013 is the ﬁrst precision dual op amp in the

8-pin industry standard conﬁguration, upgrading the per-

formance of such popular devices as the MC1458/MC1558,

LM158 and OP-221. The LT1013’s speciﬁcations are similar

to (even somewhat better than) the LT1014’s.

Both the LT1013 and LT1014 can be operated off a single

5V power supply: input common mode range includes

ground; the output can also swing to within a few millivolts

of ground. Crossover distortion, so apparent on previous

single-supply designs, is eliminated. A full set of speciﬁca-

tions is provided with ±15V and single 5V supplies.

FeaTures

applicaTions

Single Supply Operation

Input Voltage Range Extends to Ground

Output Swings to Ground While Sinking Current

Pin Compatible to 1458 and 324 with Precision Specs

Guaranteed Offset Voltage: 150µV Max

Guaranteed Low Drift: 2µV/°C Max

Guaranteed Offset Current: 0.8nA Max

Guaranteed High Gain

5mA Load Current: 1.5 Million Min

17mA Load Current: 0.8 Million Min

Guaranteed Low Supply Current: 500µA Max

Low Voltage Noise, 0.1Hz to 10Hz: 0.55µV

P-P

Low Current Noise—Better than 0P-07, 0.07pA/√Hz

Battery-Powered Precision Instrumentation

Strain Gauge Signal Conditioners

Thermocouple Ampliﬁers

Instrumentation Ampliﬁers

4mA to 20mA Current Loop Transmitters

Multiple Limit Threshold Detection

Active Filters

Multiple Gain Blocks

–

LT1014

OUTPUT A

10mV/°C

–

LT1014

OUTPUT B

10mV/°C

1.8k

YSI 44007

AT 25°C

260Ω

1684Ω

299k3k

LT1004

1.2V

–

LT1014

USE TYPE K THERMOCOUPLES. ALL RESISTORS = 1% FILM.

COLD JUNCTION COMPENSATION ACCURATE

TO ±1°C FROM 0°C TO 60°C.

USE 4TH AMPLIFIER FOR OUTPUT C.

LT1014 Distribution of Offset Voltage

3-Channel Thermocouple Thermometer

INPUT OFFSET VOLTAGE (µV)

–300 0 200

–200 –100

100 300

NUMBER OF UNITS

700

600

500

400

300

200

100

= ±15V

= 25°C

425 LT1014s

(1700 OP AMPS)

TESTED FROM

THREE RUNS

J PACKAGE

1013/14 TA02

L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear

Technology Corporation. All other trademarks are the property of their respective owners.

Summary of content (26 pages)

PAGE 1
LT1013/LT1014 Quad Precision Op Amp (LT1014) Dual Precision Op Amp (LT1013) Description Features Single Supply Operation Input Voltage Range Extends to Ground Output Swings to Ground While Sinking Current n Pin Compatible to 1458 and 324 with Precision Specs n Guaranteed Offset Voltage: 150µV Max n Guaranteed Low Drift: 2µV/°C Max n Guaranteed Offset Current: 0.8nA Max n Guaranteed High Gain 5mA Load Current: 1.5 Million Min 17mA Load Current: 0.
PAGE 2
LT1013/LT1014 Absolute Maximum Ratings (Note 1) Supply Voltage........................................................ ± 22V Differential Input Voltage........................................ ± 30V Input Voltage................. Equal to Positive Supply Voltage ............. 5V Below Negative Supply Voltage Output Short-Circuit Duration........................... Indefinite Storage Temperature Range All Grades...........................................
PAGE 3
LT1013/LT1014 Order Information LEAD FREE FINISH TAPE AND REEL PART MARKING PACKAGE DESCRIPTION TEMPERATURE RANGE LT1013DS8#PBF LT1013DS8#TRPBF 1013 8-Lead Plastic SO 0°C to 70°C LT1013IS8#PBF LT1013IS8#TRPBF 1013I 8-Lead Plastic SO –40°C to 85°C LT1013ACN8#PBF LT1013ACN8#TRPBF LT1013ACN8 8-Lead PDIP 0°C to 70°C LT1013CN8#PBF LT1013CN8#TRPBF LT1013CN8 8-Lead PDIP 0°C to 70°C LT1013DN8#PBF LT1013DN8#TRPBF LT1013DN8 8-Lead PDIP 0°C to 70°C LT1013IN8#PBF LT1013IN8#TRPBF LT1013IN
PAGE 4
LT1013/LT1014 Electrical Characteristics TA = 25°C. VS = ±15V, VCM = 0V unless otherwise noted. SYMBOL PARAMETER CONDITIONS VOS Input Offset Voltage LT1013 LT1014 LT1013D/I, LT1014D/I LT1013AM/AC LT1014AM/AC MIN TYP MAX LT1013C/D/I/M LT1014C/D/I/M MIN TYP MAX 40 50 60 60 200 150 180 Long-Term Input Offset Voltage Stability 0.4 ISO Input Offset Current 0.15 0.8 IB Input Bias Current 12 20 en Input Noise Voltage 0.
PAGE 5
LT1013/LT1014 Electrical Characteristics The l denotes the specifications which apply over the temperature range – 55°C ≤ TA ≤ 125°C. VS = ±15V, VCM = 0V unless otherwise noted. SYMBOL PARAMETER VOS Input Offset Voltage Input Offset Voltage Drift CONDITIONS MIN LT1013AM TYP MAX LT1013M/LT1014M MIN TYP MAX UNITS 80 300 90 350 110 550 µV l 80 120 250 450 450 900 90 150 300 480 480 960 100 200 400 750 750 1500 µV µV µV (Note 3) l 0.4 2.0 0.4 2.0 0.5 2.
PAGE 6
LT1013/LT1014 Electrical Characteristics The l denotes the specifications which apply over the temperature range –40°C ≤ TA ≤ 85°C for LT1013I, LT1014I, 0°C ≤ TA ≤ 70°C for LT1013C, LT1013D, LT1014C, LT1014D. VS = ±15V, VCM = 0V unless otherwise noted. SYMBOL PARAMETER VOS Input Offset Voltage Average Input Offset Voltage Drift CONDITIONS LT1013D/I, LT1014D/I VS = 5V, 0V; VO = 1.4V LT1013D/I, LT1014D/I VS = 5V, 0V; VO = 1.
PAGE 7
LT1013/LT1014 Typical Performance Characteristics Offset Voltage Drift with Temperature of Representative Units 0 –100 5 VS = 5V, 0V, –55°C TO 125°C VS = ±15V, 0V, –55°C TO 125°C 1 VS = 5V, 0V, 25°C 0.1 RS VS = ±15V, 0V, 25°C RS –200 –25 50 25 0 75 TEMPERATURE (°C) 100 0.01 125 1k LT1014 1 LT1013 CERDIP (J) PACKAGE – 0 100 0.
PAGE 8
LT1013/LT1014 Typical Performance Characteristics 4 10 3 5 2 0 VS = 5V, 0V VS = ±15V 1 –5 0 –10 –1 0 –5 –25 –10 –15 –20 INPUT BIAS CURRENT (nA) –15 –30 1.0 –30 VCM = 0V 0.6 0.4 VS = 5V, 0V VS =± V 2.5 0.2 –20 VS = 5V, 0V –15 .
PAGE 9
LT1013/LT1014 typical performance characteristics Output Short-Circuit Current vs Time VS = ±15V –55°C 25°C 20 125°C TA = –55°C, VS = ±15V 0 125°C –20 25°C –30 –55°C TA = –55°C, VS = 5V, 0V TA = 25°C, VS = 5V, 0V 1M TA = 125°C, VS = 5V, 0V 1 2 0 3 TIME FROM OUTPUT SHORT TO GROUND (MINUTES) 100k 100 1k LOAD RESISTANCE TO GROUND (Ω) 80 TA = 25°C VCM = 0V 100 CL = 100pF 140 180 5V, 0V 200 –10 0.1 0.
PAGE 10
LT1013/LT1014 Applications Information b) When the input is more than 400mV below ground (at 25°C), the input stage saturates (transistors Q3 and Q4) and phase reversal occurs at the output. This can cause lock-up in servo systems. Due to a unique phase reversal protection circuitry (Q21, Q22, Q27, Q28), the LT1013/LT1014’s outputs do not reverse, as illustrated below, even when the inputs are at –1.5V.
PAGE 11
LT1013/LT1014 Applications Information Low Supply Operation Test Circuit for Offset Voltage and Offset Drift with Temperature The minimum supply voltage for proper operation of the LT1013/LT1014 is 3.4V (three Ni-Cad batteries). Typical supply current at this voltage is 290µA, therefore power dissipation is only one milliwatt per amplifier. 50k* 15V – 100Ω* 50k* For applications information on noise testing and calculations, please see the LT1007 or LT1008 data sheet.
PAGE 12
LT1013/LT1014 typical Applications Hot-Wire Anemometer +15V 500pF Q6 TIP12O OR EQUIVALENT 2k 27Ω 1W 6 33k 2 #328 150k* – A1 LT1014 1 2k 7 150k* 1µF + 12k LT1004-1.2 6, 8 3.3k 11 500k –15V –15V REMOVE LAMP'S GLASS ENVELOPE FROM 328 LAMP. A1 SERVOS #328 LAMP TO CONSTANT TEMPERATURE. A2-A3 FURNISH LINEAR OUTPUT vs FLOW RATE. *1% RESISTOR.
PAGE 13
LT1013/LT1014 typical Applications 5V Powered Precision Instrumentation Amplifier – TO INPUT CABLE SHIELDS 8 LT1014 9 10 + 200k* 2 5V † 20k –INPUT 3 – + 10k* 10k* 1 LT1014 10k † 5V 13 – 4 RG (TYP 2k) 1µF 6 † 20k +INPUT 12 200k* 5 + † 10k* 7 LT1014 OUTPUT + 11 10k – 14 LT1014 10k* * 1% FILM RESISTOR. MATCH 10k's 0.05% 400,000 GAIN EQUATION: A = + 1. RG † FOR HIGH SOURCE IMPEDANCES, USE 2N2222 AS DIODES.
PAGE 14
LT1013/LT1014 typical Applications 5V Powered Motor Speed Controller No Tachometer Required 5V 2 0.47 330k 3 + 100k 47 1k 82Ω – A1 1/2 LT1013 1 2k Q3 2N5023 Q1 2N3904 + 1N4001 1M 2k 6.8M 0.068 1/4 CD4016 A2 1/2 LT1013 4 + 7 – 5V 8 0.068 0.47 5 1N4001 1N4148 3.3M 6 1N4148 2k MOTOR = CANON–FN30–R13N1B. A1 DUTY CYCLE MODULATES MOTOR. A2 SAMPLES MOTORS BACK EMF. Q2 EIN 0V TO 3V 1013/14 TA09 5V Powered EEPROM Pulse Generator 5V DALE #TC-10-04 1N4148 2N2222 10Ω 5V 20k 0.
PAGE 15
LT1013/LT1014 typical Applications Methane Concentration Detector with Linearized Output 5V 1 * 1% METAL FILM RESISTOR SENSOR = CALECTRO-GC ELECTRONICS #J4-807 OR FIGARO #813 14 LT1004 1.2V 0.
PAGE 16
LT1013/LT1014 typical Applications 5V Powered 4mA to 20mA Current Loop Transmitter† 5V Q3 2N2905 820Ω 10µF T1 Q1 2N2905 + 68Ω 1N4002 (4) 10µF + 74C04 (6) 0.002 0.33 100k 5V 8 A1 1/2 LT1013 1 + 100pF 5V 10k* 20mA TRIM 4k* 3 4 † 12-BIT ACCURACY. * 1% FILM. T1 = PICO-31080. 10k* 2 10k* 1k 4mA TRIM 4.3k 100Ω* 80k* 7 – – 2k A2 1/2 LT1013 LT1004 1.2V + Q4 2N2222 Q2 2N2905 820Ω 10k 10k 6 4mA TO 20mA OUT TO LOAD 2.
PAGE 17
LT1013/LT1014 typical Applications 5V Powered, Linearized Platinum RTD Signal Conditioner 2M 9 499Ω 167Ω Q1 200k Q2 2 200k 3 2N4250 (2) – A2 1/4 LT1014 + 1 150Ω 10 5k LINEARITY A4 1/4 LT1014 8 + OUTPUT 0V TO 4V = 0°C TO 400°C ±0.05°C GAIN TRIM 1k 2M 3.01k SENSOR ROSEMOUNT 118MF 7 – 1.5k – A3 1/4 LT1014 6 8.25k 50k ZERO TRIM 5 2.4k 5% + 274k 5V 4 – A1 1/4 LT1014 + 14 5V 11 13 12 LT1009 2.5V 10k 250k ALL RESISTORS ARE TRW-MAR-6 METAL FILM. RATIO MATCH 2M–200K ± 0.
PAGE 18
LT1013/LT1014 typical Applications LVDT Signal Conditioner 7 0.005 30k 0.005 30k 5 6 8 FREQUENCY = 1.5kHz 5V + 7 LT1013 11 LVDT YEL-BLK RDBLUE – BLUE –5V GRN 10k 4.7k YEL-RD 1N914 BLK 12 LT1004 1.2V 2N4338 1.2k 10µF 100k 14 0.01 13 7.5k 100k PHASE TRIM + LVDT = SCHAEVITZ E-100.
PAGE 19
LT1013/LT1014 typical Applications Low Dropout Regulator for 6V Battery 12 OUTPUT 1N914 3 8 LTC1044 2 + VBATT 6V 4 + 100Ω 10 5 10 2N2219 100k 100Ω 0.01Ω 1.2k 6 5 – 1M 3 LT1004 1.2V 2 A2 LT1013 5V OUTPUT 0.003µF 8 + 1 LT1013 – 120k 4 7 + 1N914 30k 0.009V DROPOUT AT 5mA OUTPUT. 0.108V DROPOUT AT 100mA OUTPUT. IQUIESCENT = 850µA.
PAGE 20
LT1013/LT1014 typical Applications 6V to ±15V Regulating Converter 6V 1µF 15pF 10k Q1 CLK 2 CLK 1 74C74 100kHz INPUT D1 Q1 D2 2N3906 –16V 74C00 Q2 L1 1MHY Q2 + +V 10k 10k + 2N3904 1 10 4 1.4M 0.005 2 LT1013 10k 15pF 15VOUT 16V 8 10 16V 22k 2N4391 + 22k – + 6V 200k VOUT ADJ 6V 3 100k –16V LT1004 1.2V 82k – 7 6 LT1013 5 + L1 = 24-104 AIE VERNITRON 0.
PAGE 21
LT1013/LT1014 schematic diagram 1/2 LT1013, 1/4 LT1014 V+ 9k 9k 1.6k Q13 Q6 Q5 1.6k 1.6k Q16 100Ω 1k 800Ω Q14 Q36 Q15 Q32 Q30 Q35 Q3 Q4 Q25 – Q1 + IN Q26 2.5pF 400Ω IN Q33 21pF 3.9k Q27 18Ω 2.4k Q38 Q21 OUTPUT Q2 Q41 14k Q28 400Ω Q22 Q39 Q18 Q12 Q29 Q10 4pF Q31 Q11 Q9 75pF 10pF Q7 Q8 5k 5k Q40 Q19 2k V– J1 Q37 Q34 100pF Q17 2k 42k 600Ω Q23 Q24 Q20 1.
PAGE 22
LT1013/LT1014 Package Description H Package 8-Lead TO-5 Metal Can (.200 Inch PCD) (Reference LTC DWG # 05-08-1320) .040 (1.016) MAX .335 – .370 (8.509 – 9.398) DIA .305 – .335 (7.747 – 8.509) .027 – .045 (0.686 – 1.143) 45o PIN 1 .028 – .034 (0.711 – 0.864) .050 (1.270) MAX SEATING PLANE .200 (5.080) TYP .165 – .185 (4.191 – 4.699) GAUGE PLANE .010 – .045* (0.254 – 1.143) REFERENCE PLANE .500 – .750 (12.700 – 19.050) .016 – .021** (0.406 – 0.533) .110 – .160 (2.794 – 4.
PAGE 23
LT1013/LT1014 Package Description N8 Package 8-Lead PDIP (Narrow .300 Inch) (Reference LTC DWG # 05-08-1510) .400* (10.160) MAX 8 7 6 5 1 2 3 4 .255 ± .015* (6.477 ± 0.381) .300 – .325 (7.620 – 8.255) .065 (1.651) TYP .008 – .015 (0.203 – 0.381) ( +.035 .325 –.015 8.255 +0.889 –0.381 .130 ± .005 (3.302 ± 0.127) .045 – .065 (1.143 – 1.651) ) .120 (3.048) .020 MIN (0.508) MIN .018 ± .003 .100 (2.54) BSC (0.457 ± 0.076) N8 1002 NOTE: 1.
PAGE 24
LT1013/LT1014 Package Description S6 Package 6-Lead Plastic TSOT-23 (Reference LTC DWG # 05-08-1636) .050 BSC .245 MIN .045 ±.005 .189 – .197 (4.801 – 5.004) NOTE 3 .160 ±.005 7 8 .010 – .020 s 45° (0.254 – 0.508) .008 – .010 (0.203 – 0.254) .030 ±.005 TYP 0°– 8° TYP .016 – .050 (0.406 – 1.270) 5 6 RECOMMENDED SOLDER PAD LAYOUT .053 – .069 (1.346 – 1.752) .150 – .157 (3.810 – 3.988) NOTE 3 .228 – .244 (5.791 – 6.197) .004 – .010 (0.101 – 0.254) 1 NOTE: 1. DIMENSIONS IN 3 2 4 .050 (1.
PAGE 25
LT1013/LT1014 Revision History (Revision history begins at Rev D) REV DATE DESCRIPTION PAGE NUMBER D 05/10 Updates to Typical Application “Hot-Wire Anemometer” 12 Updated Related Parts 26 10134fd Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use.
PAGE 26
LT1013/LT1014 Typical Application Step-Up Switching Regulator for 6V Battery INPUT 6V 22k 2N2222 2.2 OUTPUT 15V 50mA + LT1004 1.2V L1 1MHY 200k 5 220pF 1N5821 1M 220k 3 + 0.001 2 LT1013 1 300Ω 130k + 2N5262 6 + 8 LT1013 – 7 4 100 5.6k – 0.1 5.