Datasheet

3
LT1529
LT1529-3.3/LT1529-5
152935fb
E
LECTR
IC
AL C CHARA TERIST
ICS
PARAMETER CONDITIONS MIN TYP MAX UNITS
Dropout Voltage I
LOAD
= 700mA, T
J
= 25°C 320 430 mV
(Note 6) I
LOAD
= 700mA ● 550 mV
I
LOAD
= 1.5A, T
J
= 25°C 430 550 mV
I
LOAD
= 1.5A ● 700 mV
I
LOAD
= 3A, T
J
= 25°C 600 750 mV
I
LOAD
= 3A ● 950 mV
GND Pin Current I
LOAD
= 0mA, T
J
= 25°C 50 100 µA
(Note 7) I
LOAD
= 0mA, T
J
= 125°C (Note 8) 400 µA
I
LOAD
= 100mA, T
J
= 25°C 0.6 1.0 mA
I
LOAD
= 100mA, T
J
= 125°C (Note 8) 1.0 mA
I
LOAD
= 700mA ● 5.5 12 mA
I
LOAD
= 1.5A ● 20 40 mA
I
LOAD
= 3A ● 80 160 mA
ADJ Pin Bias Current (Notes 5, 9) T
J
= 25°C 150 300 nA
Shutdown Threshold V
OUT
= Off to On ● 1.20 2.8 V
V
OUT
= On to Off ● 0.25 0.75 V
SHDN Pin Current (Note 10) V
SHDN
= 0V ● 4.5 10 µA
Quiescent Current in Shutdown V
IN
= V
OUT
(Nominal) + 1V, V
SHDN
= 0V ● 15 30 µA
(Note 11)
Ripple Rejection V
IN
– V
OUT
= 1V (Avg), V
RIPPLE
= 0.5V
P-P
,5062dB
f
RIPPLE
= 120Hz, I
LOAD
= 1.5A
Current Limit V
IN
– V
OUT
= 7V, T
J
= 25°C5A
V
IN
= V
OUT
(Nominal) + 1.5V, ∆V
OUT
= – 0.1V ● 3.2 4.7 A
Input Reverse Leakage Current V
IN
= –15V, V
OUT
= 0V ● 1.0 mA
Reverse Output Current (Note 12) LT1529-3.3 V
OUT
= 3.3V, V
IN
= 0V 16 µA
LT1529-5 V
OUT
= 5V, V
IN
= 0V 16 µA
LT1529 (Note 6) V
OUT
= 3.8V, V
IN
= 0V 16 µA
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: The SHDN pin input voltage rating is required for a low impedance
source. Internal protection devices connected to the SHDN pin will turn on
and clamp the pin to approximately 7V or – 0.6V. This range allows the use
of 5V logic devices to drive the pin directly. For high impedance sources or
logic running on supply voltages greater than 5.5V, the maximum current
driven into the SHDN pin must be limited to less than 5mA.
Note 3: The device is tested under pulse load conditions such that T
J
= T
A
.
Note 4: Operating conditions are limited by maximum junction
temperature. The regulated output voltage specification will not apply for
all possible combinations of input voltage and output current. When
operating at maximum input voltage, the output current range must be
limited. When operating at maximum output current the input voltage
range must be limited.
Note 5: The LT1529 is tested and specified with the ADJ pin connected to
the OUTPUT pin.
Note 6: Dropout voltage is the minimum input/output voltage required to
maintain regulation at the specified output current. In dropout the output
voltage will be equal to (V
IN
– V
DROPOUT
).
Note 7: GND pin current is tested with V
IN
= V
OUT
(nominal) and a current
source load. This means that the device is tested while operating in its
dropout region. This is the worst-case GND pin current. The GND pin
current will decrease slightly at higher input voltages.
Note 8: GND pin current will rise at T
J
> 75°C. This is due to internal
circuitry designed to compensate for leakage currents in the output
transistor at high temperatures. This allows quiescent current to be
minimized at lower temperatures, yet maintain output regulation at high
temperatures with light loads. See quiescent current curve in typical
performance characteristics.
Note 9: ADJ pin bias current flows into the ADJ pin.
Note 10: SHDN pin current at V
SHDN
= 0V flows out of the SHDN pin.
Note 11: Quiescent current in shutdown is equal to the sum total of the
SHDN pin current (5µA) and the GND pin current (10µA).
Note 12: Reverse output current is tested with the V
IN
pin grounded and
the OUTPUT pin forced to the rated output voltage. This current flows into
the OUTPUT pin and out of the GND pin.
The ● denotes specifications which apply over the operating temperature range, otherwise specificatons are at T
A
= 25°C. (Note 3)