Datasheet

LTC2909
13
2909fb
APPLICATIO S I FOR ATIO
WUU
U
If the user wishes to avoid having an external capacitor,
the TMR pin should be tied to ground, switching the part
to an internal 200ms timer.
If the user requires a shorter timeout than 400s, or
wishes to perform application-specifi c processing of the
reset output, the part may be put in comparator mode by
tying the TMR pin to V
CC
. In comparator mode, the timer
is bypassed and comparator outputs go straight to the
reset output.
The current required to hold TMR at ground or V
CC
is
about 2A. To force the pin from the fl oating state to
ground or V
CC
may require as much as 100A during the
transition.
When the part is in comparator mode, one of the two
means of preventing false reset has been removed, so
a small amount of one-sided hysteresis is added to the
inputs to prevent oscillation as the monitored voltage
passes through the threshold.
This hysteresis is such
that the valid-to-invalid transition threshold is unchanged,
but the invalid-to-valid threshold is moved by about
0.7%. Thus, when the ADJ input polarity is positive,
the threshold voltage is 500mV nominal when the in-
put is above 500mV. As soon as the input drops below
500mV, the threshold moves up to 503.5mV nominal.
Conversely, when confi gured as a negative-polarity input,
the threshold is 500mV when the input is below 500mV,
and switches to 496.5mV when the input goes above
500mV.
The comparator mode feature should be enabled by directly
shorting the TMR pin to the V
CC
pin. Connecting the pin to
any other voltage may have unpredictable results.
Selecting the Reset Timing Capacitor
Connecting a capacitor, C
TMR
, between the TMR pin and
ground sets the reset timeout, t
RST
. The following formula
approximates the value of capacitor needed for a particular
timeout:
C
TMR
= t
⎯
R
⎯
S
⎯
T
• 110 [pF/ms]
Leaving the TMR pin open with no external capacitor
generates a reset timeout of approximately 400s.
Maximum length of the reset timeout is limited by the
ability of the part to charge a large capacitor on start-up.
Initially, with a large (discharged) capacitor on the TMR
pin, the part will assume it is in internal timer mode (since
the pin voltage will be at ground). If the 2A fl owing out of
the TMR pin does not charge the capacitor to the ground-
sense threshold within the fi rst 200ms after supplies
become good, the internal timer cycle will complete and
⎯
R
⎯
S
⎯
T will go high too soon.
APPLICATIO S I FOR ATIO
WUU
U
Table 3. Suggested Resistor Values for 5% Monitoring
NOMINAL
VOLTAGE
5% UV 5% OV 5% UV and OV
R
X1
R
X2
R
X1
R
X2
R
X4
R
X5
R
X6
24 232k 10.2M 102k 5.11M 82.5k 11.5k 4.12M
15 115k 3.09M 200k 6.19M 76.8k 10.7k 2.37M
12 49.9k 1.07M 102k 2.49M 76.8k 10.7k 1.87M
9 115k 1.82M 78.7k 1.43M 162k 22.6k 2.94M
5 137k 1.15M 137k 1.33M 76.8k 10.7k 732k
3.3 221k 1.15M 340k 2.05M 76.8k 10.7k 453k
2.5 115k 422k 51.1k 221k 137k 19.1k 576k
1.8 63.4k 150k 115k 324k 82.5k 11.5k 221k
1.5 59.0k 107k 137k 301k 76.8k 10.7k 158k
1.2 127k 158k 102k 158k 187k 26.1k 267k
1 200k 174k 100k 113k 107k 15.0k 105k
–5 133k 1.37M 118k 1.37M 174k 20.0k 2.00M
–9 97.6k 1.74M 115k 2.32M 182k 22.6k 3.65M
–12 107k 2.49M 40.2k 1.07M 40.2k 5.11k 1.07M
–15 107k 3.09M 309k 10.2M 309k 40.2k 10.2M
Trip points are nominal voltage ±6.5%.